warning light MAZDA MODEL CX-3 2017 (in English) Manual Online

4–101
When Driving
i-ACTIVSENSE
Switching to cruise control function
When the ON switch is pressed
continuously for about 2 seconds while
the Mazda Radar Cruise Control (MRCC)
system is turned on, the system is switched
to the cruise control function.
The Mazda Radar Cruise Control (MRCC)
indicator light (green) in the instrument
cluster turns off and the cruise control
indication is displayed in the active
driving display.


WARNING
Always turn off the cruise control
function when it is not in use:
Leaving the cruise control function
turned on when it is not in use
is dangerous as it could operate
unexpectedly, resulting in an accident.

How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
Cruise control function begins when the
SET
or SET switch is pressed.
N O T E
 


y The system may not be able to maintain
the set speed constantly depending on
driving conditions such as steep up or
down slopes.
 


y The speed will continue increasing
while the SET
switch is pressed and
held. The speed will continue
decreasing while the SET
switch is
pressed and held.

How to increase the set speed
The set speed can be increased using the
following operations:
To increase speed using the SET

switch
Press and hold the SET
switch and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph)
increments) by pressing the switch and
releasing it immediately. For example, if
the switch is pressed 4 times, the set speed
increases by about 4 km/h (4 mph).
To increase speed using accelerator
pedal
Depress the accelerator pedal and press the
SET
or SET switch at the desired
speed.
If the switch is not operated, the system
returns to the set speed after you release
your foot from the accelerator pedal.
How to Decrease the Set Speed
P r e s s t h e S E T
switch continuously and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph) increments)
by pressing the switch and releasing it
immediately. For example, if the switch
is pressed 4 times, the set vehicle speed
decreases by about 4 km/h (4 mph).
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–105
When Driving
i-ACTIVSENSE
Turn off the Smart City Brake Support (SCBS) when the vehicle is running on a chassis
roller or being towed:
Turn off the Smart City Brake Support (SCBS) system to prevent mistaken operation when
the vehicle is running on a chassis roller or being towed.
Refer to the Stopping the Smart City Brake Support (SCBS) System Operation on page
4-107 on how to turn off the Smart City Brake Support (SCBS) system.

CAUTION




¾ When driving off -road in areas where there is grass or forage, it is recommended that the
Smart City Brake Support (SCBS) system be turned off .




¾ Always use tires for all wheels that are of the specifi ed size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tires with signifi cantly diff erent wear
patterns on the same vehicle as the Smart City Brake Support (SCBS) system may not
operate normally.
 


¾ The laser sensor (front) includes a function for detecting a soiled windshield and informing
the driver, however, depending on the conditions, it may not detect plastic shopping bags,
ice or snow on the windshield. In such cases, the system cannot accurately determine a
vehicle ahead and may not be able to operate normally. Always drive carefully and pay
attention to the road ahead.

N O T E
 


y The Smart City Brake Support (SCBS) system will not operate if the driver is deliberately
performing driving operations (accelerator pedal and steering wheel).
 


y The Smart City Brake Support (SCBS) system will operate under the following conditions. 



y The engine is running.



y The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



y The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



y The Smart City Brake Support (SCBS) system is not turned off.



y The DSC is not malfunctioning.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–106
When Driving
i-ACTIVSENSE
*Some models.
 


y The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared
laser beam and receiving the beam reÀ ected off the reÀ ector of the vehicle ahead, and
then using it for the measurement. Consequently, the Smart City Brake Support (SCBS)
may not operate under the following conditions:
 


y ReÀ ection of the laser is poor due to the shape of the vehicle ahead.



y The vehicle ahead is signi¿ cantly dirty.



y Under bad weather condition, such as rain, fog and snow.



y The window washer is being used or the windshield wipers are not used when it's
raining.
 


y The windshield is dirty.



y The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


y Trucks with low loading platforms and vehicles with an extremely low or high pro¿ le.



y Vehicles with certain shapes such as a vehicle carrier. 



y Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


y Heavy luggage is loaded in the luggage compartment or on the rear seat.



y If there is the possibility of partial contact with a vehicle ahead.



y When driving on continuously curving roads, and entering and exiting exits.



y Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front).
 


y Exhaust gas from the vehicle in front, sand, snow, and water vapor rising from
manholes and grating, and water splashed into the air.
 


y When towing a malfunctioning vehicle.



y When driving with tires having signi¿ cantly different wear. 



y In the following cases, the laser sensor (front) may inadvertently determine that there is a
vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


y Objects on the road at the entrance to a curve.



y Vehicles passing in the opposite lane while making a curve.



y Metal objects, bumps, or protruding objects on the road.



y When passing through a toll gate equipped with a bar.



y When passing under a vinyl curtain or À ag.



y Plastic objects such as pylons.



y Two-wheeled vehicles, pedestrians, animals or standing trees. 



y When the system operates, the user is noti¿ ed by the À ashing Smart City Brake Support
(SCBS) indicator light (red) and the active driving display * . 


y The Smart City Brake Support (SCBS) warning light (amber) turns on when the system
has a malfunction.
  Refer to Warning Lights on page 4-25 .
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–107
When Driving
i-ACTIVSENSE
Smart City Brake Support (SCBS)
Indicator Light (Red)
If the Smart City Brake Support (SCBS) is
operating, the indicator light (red) À ashes.



Automatic Brake Operation
Display (Vehicles With Active
Driving Display)
“SCBS Automatic Brake” is displayed in
the active driving display while the SCBS
brakes or the brake assist (SCBS brake
assist) is operating.


N O T E
 


y The collision warning beep sounds
intermittently while the SCBS brake
or brake assist (SCBS brake assist) is
operating.
 


y If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds
one time after about 2 seconds and the
SCBS brake is automatically released.

Stopping the Smart City Brake
Support (SCBS) System Operation
The Smart City Brake Support (SCBS)
system can be temporarily deactivated.
When the Smart City Brake Support
(SCBS) system is turned off, the Smart
City Brake Support (SCBS) OFF indicator
light turns on.



When the engine is restarted, the system
becomes operational.
Without SCBS OFF switch
Refer to Personalization Features on page
9-10 .
With SCBS OFF switch
Press the SCBS OFF switch to turn
off the system. The Smart City Brake
Support (SCBS) OFF indicator light in the
instrument cluster will illuminate.


Press the switch again to turn the system
back on. The Smart City Brake Support
(SCBS) OFF indicator light will turn off.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–109
When Driving
i-ACTIVSENSE
N O T E
 


y The Smart Brake Support (SBS) system operates when all of the following conditions are
met:
 


y The ignition is switched ON.



y The Smart Brake Support (SBS) system is on.



y The vehicle speed is about 15 km/h or faster (10 mph or faster).



y The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


y The Dynamic Stability Control (DSC) is not operating. 



y The Smart Brake Support (SBS) system may not operate under the following conditions: 



y If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



y The vehicle is driven at the same speed as the vehicle ahead.



y The accelerator pedal is depressed.



y The brake pedal is depressed.



y The steering wheel is being operated.



y The selector lever is being operated.



y The turn signal is being used.



y When the vehicle ahead is not equipped with taillights or the taillights are turned off.



y When warnings and messages, such as a dirty windshield, related to the Forward
Sensing Camera (FSC)/laser sensor (front) are being displayed in the center display.
 


y Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


y Objects on the road at the entrance to a curve (including guardrails and snow banks).



y A vehicle appears in the opposite lane while cornering or rounding a curve.



y When crossing a narrow bridge.



y When passing under a low gate or through a tunnel or narrow gate.



y When entering an underground parking area.



y Metal objects, bumps, or protruding objects on the road.



y If you suddenly come close to a vehicle ahead.



y When driving in areas where there is high grass or forage.



y Two-wheeled vehicles such as motorbikes or bicycles.



y Pedestrians or non-metallic objects such as standing trees. 



y When the system operates, the user is noti¿ ed by the À ashing Smart Brake Support (SBS)
indicator light (red) and the active driving display.
 


y The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction. Refer to Warning/Indicator Lights on page 4-24 .

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–110
When Driving
i-ACTIVSENSE
Smart Brake Support (SBS)
Indicator Light (Red)
If the Smart Brake Support (SBS) is
operating, the indicator light (red) À ashes.



Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the active driving display.


Stopping The Smart Brake
Support (SBS) System Operation
The Smart Brake Support (SBS) system
can be temporarily deactivated.
Refer to Personalization Features on page
9-10 .
When the Smart Brake Support (SBS)
system is turned off, the Smart Brake
Support (SBS) OFF indicator light turns
on.


When the engine is restarted, the system
becomes operational.
N O T E
If the Smart Brake Support (SBS) system
operation is turned off, the Smart City
Brake Support (SCBS) system operation is
turned off simultaneously.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–112
When Driving
i-ACTIVSENSE
CAUTION
 


¾ Do not apply accessories, stickers or fi lm to the windshield near the Forward Sensing
Camera (FSC).
  If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will cause
the system to not operate correctly. Consequently, each system may not operate normally
which could lead to an unexpected accident.
 


¾ Do not disassemble or modify the Forward Sensing Camera (FSC).
 Disassembly or modifi cation of the Forward Sensing Camera (FSC) will cause a malfunction
or mistaken operation. Consequently, each system may not operate normally which could
lead to an unexpected accident.
 


¾ Heed the following cautions to assure the correct operation of the Forward Sensing Camera
(FSC).
 


¾ The direction of the Forward Sensing Camera (FSC) has been fi nely adjusted, therefore
do not change the installation position or remove the Forward Sensing Camera (FSC).
 


¾ Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get dirty.



¾ Do not remove the Forward Sensing Camera (FSC) cover.



¾ Do not place objects on the dashboard which refl ect light.



¾ Always keep the windshield glass around the camera clean by removing dirt or fogging.
Use the windshield defroster to remove fogging on the windshield.
 


¾ Consult an Authorized Mazda Dealer regarding cleaning the interior side of the
windshield around the Forward Sensing Camera (FSC).
 


¾ Consult an Authorized Mazda Dealer before performing repairs around the Forward
Sensing Camera (FSC).
 


¾ The Forward Sensing Camera (FSC) is installed to the windshield. Consult an Authorized
Mazda Dealer for windshield repair and replacement.
 


¾ When performing repairs around the rearview mirror, consult an Authorized Mazda
Dealer.
 


¾ Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If strong force is applied, stop using the Lane Departure Warning System (LDWS), the
High Beam Control System (HBC), and the Smart Brake Support (SBS) and consult an
Authorized Mazda Dealer.
 


¾ The direction in which the Forward Sensing Camera (FSC) is pointed has been fi nely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could result in damage or malfunction.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–114
When Driving
i-ACTIVSENSE
*Some models.
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
 


y Mazda Radar Cruise Control (MRCC)



y Distance Recognition Support System (DRSS)



y Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves reÀ ected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mounted behind the front emblem.

Radar sensor (front)

If the Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light (amber)
is illuminated, the area around the radar sensor may be dirty. Refer to “Warning Guidance”
in the center display (Type B audio).
Refer to If a Warning Light Turns On or Flashes on page 7-27 .
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–116
When Driving
i-ACTIVSENSE
N O T E
 


y Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions correctly and each system may not operate normally.
 


y The rear surface of a vehicle ahead does not reÀ ect radio waves effectively, such as
an unloaded trailer or an automobile with a loading platform covered by a soft top,
vehicles with a hard plastic tailgate, and round-shaped vehicles.
 


y Vehicles ahead with low vehicle height and thus less area for reÀ ecting radio waves.



y Visibility is reduced due to a vehicle ahead casting off water, snow, or sand from its
tires and onto your windshield.
 


y The luggage compartment is loaded with heavy objects or the rear passenger seats are
occupied.
 


y Ice, snow, or soiling is on the front surface of the front emblem.



y During inclement weather such as rain, snow, or sand storms.



y When driving near facilities or objects emitting strong radio waves. 



y Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions.
 


y The beginning and end of a curve.



y Roads with continuous curves.



y Narrow lane roads due to road construction or lane closures.



y The vehicle ahead enters the radar sensor's blind spot.



y The vehicle ahead is running abnormally due to accident or vehicle damage.



y Roads with repeated up and down slopes



y Driving on poor roads or unpaved roads.



y The distance between your vehicle and the vehicle ahead is extremely short.



y A vehicle suddenly comes close such as by cutting into the lane. 



y To prevent incorrect operation of the system, use tires of the same speci¿ ed size,
manufacturer, brand, and tread pattern on all four wheels. In addition, do not use tires
with signi¿ cantly different wear patterns or tire pressures on the same vehicle (Including
the temporary spare tire).
 


y If the battery power is weak, the system may not operate correctly.



y If the vehicle is driven on a road with little traf¿ c and few vehicles ahead or obstructions
for the radar sensor (front) to detect, the sensor detects that the radar sensor (front) is
dirty and the Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light
(amber) may be temporarily turned on. However, it does not indicate a malfunction.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–123
When Driving
Cruise Control
Cruise Main Indicator Light
(Amber)/Cruise Set Indicator
Light (Green)

The indicator light has two colors.
Cruise Main Indicator Light (Amber)
The indicator light illuminates amber
when the cruise control system is
activated.
Cruise Set Indicator Light (Green)
The indicator light illuminates green when
a cruising speed has been set.
Activation/Deactivation
To activate the system, press the ON
switch. The cruise main indicator light
(Amber) illuminates.
To deactivate the system, press the OFF
switch.
The cruise main indicator light (Amber)
turns off.
WARNING
Always turn off the cruise control system
when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as
the cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.

N O T E
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the cruise control
system operable, the system will be
operable when the ignition is switched ON
the next time.

To Set Speed
1. Activate the cruise control system
by pressing the ON switch. The
cruise main indicator light (Amber)
illuminates.
2. Accelerate to the desired speed, which
must be more than 25 km/h (16 mph).
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD