windshield wipers MAZDA MODEL CX-3 2017 Owners Manual (in English)

4–1*Some models.
4When Driving
Information concerning safe driving and stopping.

Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-10

Instrument Cluster and Display ...... 4-12
Meters and Gauges ....................... 4-12
Active Driving Display
* ............... 4-22
Warning/Indicator Lights ............. 4-24

Transaxle ............................................ 4-30
Automatic Transaxle Controls ..... 4-30

Switches and Controls ...................... 4-41
Lighting Control ........................... 4-41
Fog Lights
* ................................... 4-46
Turn and Lane-Change Signals .... 4-46
Windshield Wipers and Washer ... 4-47
Rear Window Wiper and
Washer .......................................... 4-51
Rear Window Defogger ............... 4-51
Horn ............................................. 4-53
Hazard Warning Flasher ............... 4-53

Brake .................................................. 4-54
Brake System ............................... 4-54
Hill Launch Assist (HLA) ............ 4-56

ABS/TCS/DSC ................................... 4-58
Antilock Brake System (ABS) ..... 4-58
Traction Control System (TCS) ... 4-59
Dynamic Stability Control
(DSC) ........................................... 4-61

Fuel Economy Monitor ..................... 4-62
Fuel Economy Monitor * ............... 4-62

Drive Selection ................................... 4-64
Drive Selection ............................. 4-64

i-ACTIV AWD ................................... 4-65
i-ACTIV AWD Operation ............ 4-65

Power Steering................................... 4-67
Power Steering ............................. 4-67

i-ACTIVSENSE................................. 4-68
i-ACTIVSENSE
* .......................... 4-68
Adaptive Front Lighting System
(AFS)
* .......................................... 4-70
High Beam Control System (HBC) * ... 4-71
Lane Departure Warning System
(LDWS)
* ...................................... 4-74
Blind Spot Monitoring (BSM) * .... 4-80
Distance Recognition Support System
(DRSS)
* ........................................ 4-86
Rear Cross Traf¿ c Alert
(RCTA)
* ....................................... 4-89
Mazda Radar Cruise Control
(MRCC)
* ...................................... 4-92
Smart City Brake Support
(SCBS)
* ...................................... 4-103
Smart Brake Support (SBS) * ...... 4-108

Forward Sensing Camera (FSC) * ... 4-111
Radar Sensor (Front) * ................. 4-114
Laser Sensor (Front) * ................. 4-117
Radar Sensors (Rear) * ................ 4-120
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–43
When Driving
Switches and Controls
CAUTION
 


¾ Do not shade the light sensor by adhering a sticker or a label on the windshield. Otherwise
the light sensor will not operate correctly.

 


¾ The light sensor also works as a rain sensor for the auto-wiper control. Keep hands and
scrapers clear of the windshield when the wiper lever is in the
position and the
ignition is switched ON as fi ngers could be pinched or the wipers and wiper blades could be
damaged when the wipers activate automatically. If you are going to clean the windshield,
be sure the wipers are turned off completely when it is particularly tempting to leave the
engine running. This is particularly important when clearing ice and snow.

N O T E
 


y The headlights, other exterior lights and dashboard illumination may not turn off
immediately even if the surrounding area becomes well-lit because the light sensor
determines that it is night time if the surrounding area is continuously dark for several
minutes such as inside long tunnels, traf¿ c jams inside tunnels, or in indoor parking lots.

 In this case, the lights turn off if the light switch is turned to the position.



y (Without auto headlight off function) 
 When the headlight switch is in the position and the ignition is switched to ACC or
the ignition is switched off, the headlights, other exterior lights and dashboard
illumination will turn off.
 


y The dashboard illumination can be adjusted by rotating the knob in the instrument cluster.
Also, the day/night mode can be changed by rotating the knob until a beep sound is heard.
To adjust the brightness of the dashboard illumination:
  Refer to Dashboard Illumination on page 4-19 .



y The sensitivity of the AUTO lights may be changed by an Authorized Mazda Dealer.
 Refer to Personalization Features on page 9-10 .
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–47
When Driving
Switches and Controls
N O T E
 


y If an indicator light stays on without
À ashing or if it À ashes abnormally, one
of the turn signal bulbs may be burned
out.
 


y A personalized function is available to
change the turn indicator sound volume.
(page 9-10 )

Lane-Change Signals
Move the lever halfway toward the
direction of the lane change—until the
indicator À ashes— and hold it there. It will
return to the off position when released.
Three-Flash Turn Signal
After releasing the turn signal lever, the
turn signal indicator À ashes three times.
The operation can be cancelled by moving
the lever in the direction opposite to which
it was operated.
N O T E
The three-À ash turn signal function can be
switched to operable/inoperable using the
personalization function.
Refer to Personalization Features on page
9-10 .

Windshield Wipers and
Washer
The ignition must be switched ON to use
the wipers.
WARNING
Use only windshield washer fl uid or
plain water in the reservoir:
Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windshield, it will dirty the windshield,
aff ect your visibility, and could result in
an accident.

Only use windshield washer fl uid mixed
with anti-freeze protection in freezing
weather conditions:
Using windshield washer fl uid without
anti-freeze protection in freezing
weather conditions is dangerous as
it could freeze on the windshield and
block your vision which could cause
an accident. In addition, make sure
the windshield is suffi ciently warmed
using the defroster before spraying the
washer fl uid.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–48
When Driving
Switches and Controls
N O T E
If the windshield wipers are operated
under cold weather conditions or
during snowfall, they could stop due to
accumulated snow on the windshield.
If the windshield wipers stop due to
accumulated snow on the windshield,
park the vehicle in a safe place, turn the
wiper switch off, and then remove the
accumulated snow. If the wiper switch is
turned to another position other than OFF,
the wipers will operate. If the wipers do
not operate even though the wiper switch
is turned to a position other than OFF,
consult an Authorized Mazda Dealer as
soon as possible.

Windshield Wipers
Turn the wipers on by pressing the lever
up or down.
With intermittent wiper



Switch
Position Wiper operation


Operation while pulling up lever


Stop


Intermittent


Low speed


High speed
Variable-speed intermittent wipers
Set the lever to the intermittent position
and choose the interval timing by rotating
the ring.


INT ringFast
Slow

With auto-wiper control



Switch
Position Wiper operation
Operation while pulling up lever
Stop
Auto control
Low speed
High speed

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–49
When Driving
Switches and Controls
Auto-wiper control
When the wiper lever is in the

position, the rain sensor senses the amount
of rainfall on the windshield and turns the
wipers on or off automatically (off—
intermittent—low speed—high speed).

The sensitivity of the rain sensor can be
adjusted by turning the switch on the
wiper lever.
From the center position (normal), rotate
the switch upward for higher sensitivity
(faster response) or rotate it downward for
less sensitivity (slower response).


Higher sensitivity
Less sensitivitySwitch
Center
position

CAUTION
 


¾ Do not shade the rain sensor by
adhering a sticker or a label on the
windshield. Otherwise the rain sensor
will not operate correctly.
 

 


¾ When the wiper lever is in the
position and the ignition is switched ON,
the wipers may move automatically in
the following cases:
 


¾ If the windshield above the rain
sensor is touched or wiped with a
cloth.
 


¾ If the windshield is struck with a hand
or other object from either outside or
inside the vehicle.
  Keep hands and scrapers clear of the
windshield when the wiper lever is in the

position and the ignition is
switched ON as fi ngers could be pinched
or the wipers and wiper blades damaged
when the wipers activate automatically.
  If you are going to clean the windshield,
be sure the wipers are turned off
completely (when it is most likely
that the engine is left running) this is
particularly important when clearing ice
and snow.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–50
When Driving
Switches and Controls
N O T E
 


y Switching the auto-wiper lever from the

to the position while driving
activates the windshield wipers once,
after which they operate according to
the rainfall amount.
 


y The auto-wiper control may not operate
when the rain sensor temperature is
about -10 °C (14 °F) or lower, or about
85 °C (185 °F) or higher.
 


y If the windshield is coated with water
repellent, the rain sensor may not be
able to sense the amount of rainfall
correctly and the auto-wiper control
may not operate properly.
 


y If dirt or foreign matter (such as ice or
matter containing salt water) adheres
to the windshield above the rain sensor,
or if the windshield is iced, it could
cause the wipers to move automatically.
However, if the wipers cannot remove
this ice, dirt or foreign matter, the auto-
wiper control will stop operation. In
this case, set the wiper lever to the low
speed position or high speed position
for manual operation, or remove the ice,
dirt or foreign matter by hand to restore
the auto-wiper operation.
 


y If the auto-wiper lever is left in the
position, the wipers could operate
automatically from the effect of strong
light sources, electromagnetic waves, or
infrared light because the rain sensor
uses an optical sensor. It is
recommended that the auto-wiper lever
be switched to the
position other
than when driving the vehicle under
rainy conditions.
 


y If the headlight switch and the
windshield wiper switch are in
,
and the wipers are operated at low or
high speed by the auto wiper control for
several seconds, bad weather conditions
are determined and the headlights may
be turned on.
 


y The auto-wiper control functions can
be turned off. Refer to Personalization
Features on page 9-10 .

Windshield Washer
Pull the lever toward you and hold it to
spray washer À uid.


Washer OFF

N O T E
If the windshield washer is turned on when
the windshield wipers are not operating,
the windshield wipers operate a few times.

If the washer does not work, inspect the
À uid level (page 6-32 ). If the À uid level
is normal, consult an Authorized Mazda
Dealer.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–104
When Driving
i-ACTIVSENSE
WARNING
Do not rely on the Smart City Brake Support System (SCBS) as a substitute for safer
driving:
The Smart City Brake Support (SCBS) system cannot compensate for unsafe and reckless
driving, excessive speed, tailgating (following another vehicle too closely), and driving on
slippery roads such as wet, snowy, and icy roads (reduced tire friction and road contact
because of water on the road surface). You can still have an accident.

Do not rely completely on the Smart City Brake Support (SCBS) system:
 


¾ The Smart City Brake Support (SCBS) system is only designed to reduce damage in the
event of a collision. Over reliance on the system leading to the accelerator pedal or
brake pedal being mistakenly operated could result in an accident.
 


¾ The Smart City Brake Support (SCBS) is a system which operates in response to a
vehicle ahead. The system may not be able to detect or react to two-wheeled vehicles
or pedestrians.
 


¾ The laser sensor (front) for the Smart City Brake Support (SCBS) system is installed near
the rearview mirror. To assure the correct operation of the Smart City Brake Support
(SCBS), heed the following cautions.
 

¾
 Do not apply stickers to the surface of the windshield near the laser sensor (front)
(including transparent stickers). Otherwise, the laser sensor (front) may not be able
to detect vehicles ahead which could result in an accident.
 

¾
 Do not apply coating agent to the windshield. Otherwise, the laser sensor (front)
may not be able to detect vehicles or obstructions in front which could result in an
accident.
 

¾
 Do not disassemble the laser sensor (front).


¾
 If cracks or damage caused by fl ying gravel or debris is visible near the laser sensor
(front), stop using the Smart City Brake Support (SCBS) system immediately and
have your vehicle inspected by an Authorized Mazda Dealer. If the vehicle continues
to be driven with cracks or scratch marks left on the windshield near the laser sensor
(front), the system may operate unnecessarily and cause an unexpected accident.
  Refer to Stopping The Smart City Brake Support (SCBS) System Operation on page
4-107 .
 

¾
 When replacing the windshield wipers or windshield, consult an Authorized Mazda
Dealer.


Do not modify the suspension:
If the vehicle height or inclination is changed, the system will not be able to correctly
detect vehicles ahead. This will result in the Smart City Brake Support (SCBS) system not
operating normally or mistakenly operating, which could cause a serious accident.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–106
When Driving
i-ACTIVSENSE
*Some models.
 


y The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared
laser beam and receiving the beam reÀ ected off the reÀ ector of the vehicle ahead, and
then using it for the measurement. Consequently, the Smart City Brake Support (SCBS)
may not operate under the following conditions:
 


y ReÀ ection of the laser is poor due to the shape of the vehicle ahead.



y The vehicle ahead is signi¿ cantly dirty.



y Under bad weather condition, such as rain, fog and snow.



y The window washer is being used or the windshield wipers are not used when it's
raining.
 


y The windshield is dirty.



y The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


y Trucks with low loading platforms and vehicles with an extremely low or high pro¿ le.



y Vehicles with certain shapes such as a vehicle carrier. 



y Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


y Heavy luggage is loaded in the luggage compartment or on the rear seat.



y If there is the possibility of partial contact with a vehicle ahead.



y When driving on continuously curving roads, and entering and exiting exits.



y Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front).
 


y Exhaust gas from the vehicle in front, sand, snow, and water vapor rising from
manholes and grating, and water splashed into the air.
 


y When towing a malfunctioning vehicle.



y When driving with tires having signi¿ cantly different wear. 



y In the following cases, the laser sensor (front) may inadvertently determine that there is a
vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


y Objects on the road at the entrance to a curve.



y Vehicles passing in the opposite lane while making a curve.



y Metal objects, bumps, or protruding objects on the road.



y When passing through a toll gate equipped with a bar.



y When passing under a vinyl curtain or À ag.



y Plastic objects such as pylons.



y Two-wheeled vehicles, pedestrians, animals or standing trees. 



y When the system operates, the user is noti¿ ed by the À ashing Smart City Brake Support
(SCBS) indicator light (red) and the active driving display * . 


y The Smart City Brake Support (SCBS) warning light (amber) turns on when the system
has a malfunction.
  Refer to Warning Lights on page 4-25 .
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–118
When Driving
i-ACTIVSENSE
CAUTION
Heed the following precautions to assure correct operation of the system.  


¾ Keep the windshield clean at all times.



¾ Do not apply stickers to the surface of the windshield (including transparent stickers).



¾ If cracks or damage caused by fl ying gravel or debris is visible near the laser sensor
(front), stop using the system immediately and have your vehicle inspected by an
Authorized Mazda Dealer.
  Refer to the Personalization Features on page 9-10 on how to turn off the system.



¾ Do not apply a coating agent to the windshield.



¾ When replacing the windshield wipers or windshield, consult an Authorized Mazda
Dealer.
 


¾ Never remove the sensor.



¾ A removed sensor will not meet the conditions for a class 1M laser under the IEC
60825-1 specifi cation and therefore eye safety cannot be assured.
 


¾ Do not peer into the sensor using optical instruments with a magnifi cation function
such as magnifying glasses, and microscopic and objective lenses within a distance of
100 mm (3.94 in) from the sensor.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–34
Maintenance and Care
Owner Maintenance
Wiper Blades
CAUTION
 


¾ Hot waxes applied by automatic car
washers have been known to aff ect the
wiper's ability to clean windows.
 


¾ To prevent damage to the wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on or near
them.
 


¾ When the wiper lever is in the AUTO
position and the ignition is switched ON,
the wipers may move automatically in
the following cases:
 


¾ If the windshield above the rain
sensor is touched.
 


¾ If the windshield above the rain
sensor is wiped with a cloth.
 


¾ If the windshield is struck with a hand
or other object.
 


¾ If the rain sensor is struck with a hand
or other object from inside the vehicle.
  Be careful not to pinch hands or fi ngers
as it may cause injury, or damage the
wipers. When washing or servicing the
vehicle, make sure the wiper lever is in
the OFF position.

Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.

If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
Replacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, do not try to
sweep the wiper arm by hand.

N O T E
When raising both windshield wiper arms,
raise the driver's side wiper arm ¿ rst.
When lowering the wiper arms, slowly
lower the wiper arm from the passenger's
side ¿ rst while supporting it with your
hand. Forcefully lowering the wiper arms
could damage the wiper arm and blade,
and may scratch or crack the windshield.

1. Raise the wiper arm.
2. Open the clip and slide the blade
assembly in the direction of the arrow.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD