warning light MAZDA MODEL CX-5 2017 - RHD (UK, Australia) (in English) Owner's Guide

The system will be triggered again (up to
10 times) if one of the above conditions
remains.
•(With the intrusion sensor)
Disconnecting the battery terminal (the
hazard warning lights do not flash).
The system will be triggered about 10
times.
NOTE
•The liftgate does not open while the
theft-deterrent system is operating.
•For vehicles equipped with the power
liftgate, the liftgate can be opened even
while the theft-deterrent system is
operating by pressing the power liftgate
button on the transmitter or the electric
liftgate opener switc h while carrying the
key.
•If the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the hazard
warning lights will flash when the
battery is charged or replaced.
â–¼ How to Arm the System
1. Close the windows and the sunroof*
securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof
*
open, the system can be armed,
however, leaving the windows and the
sunroof
* even partially open can invite
theft, and wind blowing into the
vehicle could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and the liftgate are closed.
4. Press the lock butto n on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will flash
once.
(With the advanced keyless function)
Press a request switch.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully armed.
NOTE
•The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate and the bonnet closed.
Refer to Transmitter on page 3-4.
•The system will disarm if one of the
following operations takes place
within 20 seconds after pressing the
lock button:
•Unlocking any door.
•Opening any door.
•Opening the bonnet.
•Switching the ignition ON.
To rearm the system, do the arming
procedure again.
Before Driving
Security System
3-50*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary
key while the theft-deterrent system
is armed, the hazard warning lights
will flash once to indicate that the
system is armed.
â–¼Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the
alarm from triggering
unnecessarily.
•Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
•Leaving an object inside the vehicle that
can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
•Hanging small objects/accessories in the
vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
•Parking in an area where there is strong
vibration or loud noise.
•When using a high pressure or
automatic car wash.
•Continuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
•Doors are locked with a window or the
sunroof
* left open.
•An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the liftgate remains closed
for 30 seconds, all the doors and the
liftgate automatically re-lock and the theft
deterrent system arms even if a window
and the sunroof
* is left open.

To cancel the intrusion sensor, press the
intrusion sensor cancel button on the
transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash three
times.
NOTE
•To reactivate the intrusion sensor, turn
off the armed theft-deterrent system and
then rearm it.
•The intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion sensor,
press the intrusion sensor cancel button
each time the theft-deterrent system is
armed.
â–¼ To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
•Pressing the unlock button on the
transmitter.
•Starting the engine with the push button
start.
•(With the advanced keyless function)
•Pressing a request switch on the
doors.
The hazard warning lights will flash twice.
Before Driving
Security System
*Some models.3-51
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When the doors are unlocked by pressing
the unlock button on the transmitter while
the theft-deterrent system is turned off, the
hazard warning lights will flash twice to
indicate that the sy stem is turned off.
â–¼To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
•Pressing the unlock button on the
transmitter.
•Starting the engine with the push button
start.
•(With the advanced keyless function)
•Pressing a request switch on the
doors.
•Pressing the electric liftgate opener
while the key is being carried.
•Pressing the power liftgate button on
the transmitter.
The hazard warning lights will flash twice.
Before Driving
Security System
3-52
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

4When Driving
Information concerning safe driving and stopping.
Start/Stop Engine.............................. 4-4 Ignition Switch........ ..................... 4-4
Starting the Engine....................... 4-5
Turning the Engine Off............... 4-11
i-stop
*......................................... 4-12
Instrument Cluster and Display............
........................................................... 4-22 Meters and Gauges..................... 4-22
Multi-information Display
*........ 4-31
Active Driving Display
*............. 4-39
Warning/Indicator Lights............4-42
Manual Transaxle Operation......... 4-51 Manual Transaxle Shift
Pattern......................................... 4-51
Automatic Transaxle....................... 4-54 Automatic Transaxle
Controls...................................... 4-54
Shift-Lock System...................... 4-55
Transaxle Ranges........................4-56
Manual Shift Mode..................... 4-58
Driving Tips................................4-62
Switches and Controls..................... 4-63
Lighting Control......................... 4-63
Front Fog Lights
*....................... 4-68
Rear Fog Light
*.......................... 4-69
Turn and Lane-Change
Signals........................................ 4-70
Windscreen Wipers and
Washer........................................ 4-71
Rear Window Wiper and
Washer........................................ 4-75
Headlight Washer
*...................... 4-75
Rear Window Defogg er.............. 4-76
Horn............................................ 4-78
Hazard Warning Flasher............. 4-78
Brake................................................ 4-80 Brake System.............................. 4-80
AUTOHOLD.............................. 4-84
Emergency Stop Signal
System........................................ 4-88
Hill Launch Assist (HLA).......... 4-89
ABS/TCS/DSC................................. 4-90 Antilock Brake System
(ABS)..........................................4-90
Traction Control System
(TCS).......................................... 4-91
Dynamic Stability Control
(DSC)..........................................4-93
i-ELOOP.......................................... 4-94 i-ELOOP
*................................... 4-94
*Some models.4-1
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Fuel Economy Monitor................... 4-96Fuel Economy Monitor
*............. 4-96
Drive Selection............................... 4-101 Drive Selection
*....................... 4-101
i-ACTIV AWD............................... 4-103 i-ACTIV AWD Operation
*...... 4-103
Power Steering...............................4-104 Power Steering......................... 4-104
i-ACTIVSENSE............................. 4-105 i-ACTIVSENSE....................... 4-105
Adaptive Front Lighting System
(AFS)
*...................................... 4-108
High Beam Control System
(HBC)
*......................................4-109
Adaptive LED Headlights
(ALH)
*...................................... 4-112
Blind Spot Monitoring (BSM)
*.........
.................................................. 4-115
Traffic Sign Recognition System
(TSR)
*...................................... 4-120
Distance Recognition Support
System (DRSS)
*....................... 4-127
Driver Attenti on Alert (DAA)
*..........
.................................................. 4-131
Rear Cross Traffic Alert (RCTA)
*.....
.................................................. 4-133
Mazda Radar Cruise Control
(MRCC) (Manual Transaxle and
Ta i w a n )
*................................... 4-137
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) (Automatic
Transaxle except Taiwan)
*....... 4-149
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS)
*.................................. 4-163
Adjustable Speed Limiter (ASL)
*......
.................................................. 4-174
Advanced Smart City Brake Support
(Advanced SCBS) (Except Indonesia
and Taiwan)
*............................ 4-181
Smart City Brake Support [Forward]
(SCBS F) (Indonesia and
Ta i w a n )
*................................... 4-185
Smart City Brake Support [Reverse]
(SCBS R)
*................................ 4-189
Smart Brake Support (SBS)
*.... 4-193
Forward Sensing Camera (FSC)
*......
.................................................. 4-196
Radar Sensor (Front)
*.............. 4-201
Radar Sensors (Rear)
*.............. 4-204
Ultrasonic Sensor (Rear)
*.........4-206
Cruise Control............................... 4-207 Cruise Control
*.........................4-207
Tyre Pressure Monitoring
System.............................................4-212 Tyre Pressure Monitoring
System
*..................................... 4-212
Diesel Particulate Filter................ 4-216 Diesel Particulate Filter
(SKYACTIV-D 2.2)..................4-216
Rear View Monitor....................... 4-217 Rear View Monitor
*................. 4-217
4-2*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.
ON
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition is
switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-42).
NOTE
(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
When the push button start is pressed to
ON, the sound of the fuel pump motor
operating near the fuel tank can be heard.
This does not indi cate an abnormality.
Starting the Engine
WA R N I N G
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who use
medical devices, ask the medical device
manufacturer or your physician if radio
waves from the key w ill affect the device.
NOTE
•The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
•The engine can be started when the push
button start is pressed from off, ACC, or
ON.
•The push button start system functions
(function which can start the engine by
only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9.
•After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
When Driving
Start/Stop Engine
4-5
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC or
ON (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
•Under the following conditions, the
KEY warning light (red) flashes after
the push button start is pressed. This
informs the driver that the push
button start will not switch to ACC,
even if it is pressed from off (for
vehicles with a type A instrument
cluster (page 4-42), messages are
displayed in the instrument cluster).
•The key battery is dead.
•The key is out of operational
range.
•The key is placed in areas where it
is difficult for the system to detect
the signal (page 3-6).
•A key from another manufacturer
similar to the key is in the
operational range.
•(Forced engine starting method)
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may
not start using the usual starting
method (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your
vehicle inspected at an expert
repairer, we recommend an
Authorised Mazda Repairer as soon
as possible. If this occurs, the engine
can be force-started. Press and hold
the push button start until the engine
starts. Other procedures necessary
for starting the engine, such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) are required.
•When the engine is force-started, the
KEY warning light (red) (if
equipped) remains illuminated and
the push button start indicator light
(amber) remains flashing.
•(Automatic transaxle)
When the selector lever is in the
neutral (N) position, the KEY
indicator light (green) (if equipped)
and the push button start indicator
light (green) do not illuminate.
7. Press the push button start after both
the KEY indicator light (green) (if
equipped) in the ins trument cluster and
the push button start indicator light
(green) illuminate.
When Driving
Start/Stop Engine
4-7
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When touching the push button start
using the backside of the key as shown
in the illustration, touch the push
button start with the lock switch side of
the key facing up.
5. Verify that the push button start
indicator light (green) turns on.
6. Press the push button start to start the engine.
NOTE
•The engine cannot be started unless
the clutch pedal is fully depressed
(manual transaxle) or the brake
pedal is fully depressed (automatic
transaxle).
•If there is a malfunction with the
push button start function, the push
button start indica tor light (amber)
flashes. In this ca se, the engine may
start, however, have the vehicle
checked at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
•If the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle checked
at an expert repairer, we recommend
an Authorised Mazda Repairer.
•To switch the ignition position
without starting the engine, perform
the following operations after the
push button start indicator light
(green) turns on.
1. Release the clutch pedal (manual transaxle) or brake pedal
(automatic transaxle).
2. Press the push button start to
switch the igniti on position. The
ignition switches in the order of
ACC, ON, and off each time the
push button start is pressed. To
switch the ignition position
again, perform the operation
from the beginning.
â–¼ Emergency Operation for Starting
the Engine
If the KEY warning ligh
t (red) illuminates,
or the push button start indicator light
(amber) flashes, this could indicate that
the engine may not s tart using the usual
starting method (for vehicles with a type A
instrument cluster (page 4-42), messages
are displayed in the instrument cluster).
Have your vehicle inspected at an expert
repairer, we recommend an Authorised
Mazda Repairer as soon as possible. If this
occurs, the engine can be force-started.
Press and hold the push button start until
the engine starts. Other procedures
necessary for starting the engine such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the bra ke pedal (automatic
transaxle) are required.
When Driving
Start/Stop Engine
4-10
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Turning the Engine Off
WA R N I N G
Do not stop the engine while the vehicle is
moving:
Stopping the engine while the vehicle is
moving for any reason other than in an
emergency is dangerous. Stopping the
engine while the vehicle is moving will
result in reduced braking ability due to the
loss of power braking, which could cause
an accident and serious injury.
1. Stop the vehicle completely.
2.(Manual transaxle)
Shift into neutral and set the parking
brake.
(Automatic transaxle)
Shift the selector lever to the P
position and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure the
push button start is off.
NOTE
•(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the A/C
is on or off, to cool the engine
compartment quickly.
•If the system detects that the remaining
battery power of the key is low when the
ignition is switched from ON to ACC or
OFF, the following is indicated.
Replace with a new battery before the
key becomes unusable.
Refer to Key Battery Replacement on
page 6-41.
(Vehicle equipped with Type A
instrument cluster)
A message is indicated in the display of
the instrument cluster.
(Vehicle equipped with Type B
instrument cluster)
The KEY indicator li ght (green) flashes
for approximately 30 seconds.
Refer to Warning/Indicator Lights on
page 4-42.
•(Automatic transaxle)
If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.
â–¼Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engi
ne is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
When Driving
Start/Stop Engine
4-11
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
•(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
The engine is warmed up.
•(SKYACTIV-D 2.2)
•The engine is not cold.
•The fuel injection amount learning, which is performed periodic ally and automatically,
is not being performed.
•The engine has been started and the vehicle is driven for a cer tain period.
•The engine is started with the bonnet closed.
•The battery is in good condition.
•All doors, liftgate, and bonnet are closed.
•The driver's seat belt is fastened.
•The air conditioner is not operating with the airflow mode dial in the position.
•(Automatic air-conditioning)
•The temperature setting dial of the air conditioner is in a position other than maximum
heating or maximum cooling (A/C ON) position.
•The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
•The i-stop warning light (ambe r) is not turned on/flashing.
•The keyless entry & push button start system functions are norm al.
•The brake vacuum is sufficiently high.
•The steering wheel is not being operated.
•(Manual transaxle)
•The vehicle speed is 3 km/h (1.8 mph) or less.
•The shift lever is in the neutral position.
•The clutch pedal is not depressed.
•(Automatic transaxle)
•The vehicle is stopped.
•The selector lever is in the D or M position (not in second gea r fixed mode).
•The automatic transaxle fluid has warmed up sufficiently.
•The automatic transaxle fluid temperature is not abnormally hig h.
•The steering wheel is almost in the straight-ahead position (idling may not stop even
with the steering wheel in the st raight-ahead position if force is applied to the steering
wheel. Release t he force applied to the steering wheel to stop engine idling).
•The vehicle is stopped by depressing the brake pedal.
When Driving
Start/Stop Engine
4-14
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2