check engine MAZDA MODEL CX-5 2017 (in English) User Guide

4–126
When Driving
i-ACTIVSENSE
Setting the System
The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop \
& Go
function) system operates when all of the following conditions are met.\
  Vehicle speed is 0 km/h (0 mph) to 145 km/h (90 mph)  The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop \
& Go
function) is turned on.
   The brake pedal is not depressed.  The electric parking brake (EPB) is released (electric parking brake \
(EPB) indicator light
is turned off).
   There is no problem with the DSC.  All the doors are closed.  The driver's seat belt is fastened.  The selector lever is in the drive (D) position or manual (M) positi\
on (manual mode).
NOTE
  In the following cases, the Mazda Radar Cruise Control with Stop & Go function (MRCC
with Stop & Go function) system is canceled when the vehicle is traveli\
ng at 30 km/h
(20 mph) or less and “Mazda Radar Cruise Control disabled under 30 km/h (20 mph) ” is
displayed in the multi-information display.
  The Forward Sensing Camera (FSC) cannot detect target objects (There is problem
with the Forward Sensing Camera (FSC) or windshield is dirty).
  There is a problem with the stop hold control function.  There is a problem with the electric parking brake (EPB).   It may not be possible to set the Mazda Radar Cruise Control with Stop & Go function
(MRCC with Stop & Go function) system directly after starting the engine, while the DSC
operation is being checked.


CANCEL switchRES switch
OFF switch
switch switch
MODE switch
SET- switch
SET+ switch

CX-5_8FN1-EA-16L_Edition1.indb 1262016/12/12 10:06:10

5–4
Interior Features
Climate Control System
Operating Tips
  Operate the climate control system with
the engine running.
   To prevent the battery from being
discharged, do not leave the fan control
dial/switch on for a long period of time
with the ignition switched ON when the
engine is not running.
   Clear all obstructions such as leaves,
snow and ice from the hood and the air
inlet in the cowl grille to improve the
system effi ciency.
  Use the climate control system to defog
the windows and dehumidify the air.
   The recirculate mode should be used
when driving through tunnels or while in
a traffi c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
   Use the outside air position for
ventilation or windshield defrosting.
   If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the climate control system.

   Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
   Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
effi cient.
 The refrigerant speci fi cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before re fi lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
 For details, consult an Authorized Mazda Dealer.

Type A

Label

Type B

Label

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:06:22

5–65
Interior Features
Audio Set [Type A (non-touchscreen)]
Troubleshooting
Mazda Bluetooth ® Hands-Free Customer Service
If you have any problems with Bluetooth
® , contact our toll-free customer service center.    U.S.A.  Phone: 800-430-0153 (Toll-free) Web: www.mazdausa.com/mazdaconnect   Canada  Phone: 800-430-0153 (Toll-free) Web: www.mazdahandsfree.ca   Mexico  Center of Attention to Client (CAC) Phone: 01-800-01-MAZDA (Toll-free) Web: www.mazdamexico.com.mx

Bluetooth
® Device pairing, connection problems
Symptom Cause Solution method
Unable to perform pairing — First make sure the device is
compatible with the Bluetooth
®
unit, and then check whether the
Bluetooth
® function and the Find
Mode/Visible setting *1 on the device
are turned on. If pairing is still
not possible after this, contact an
Authorized Mazda Dealer or Mazda
Bluetooth
® Hands-Free Customer
Service.
Pairing cannot be performed again The pairing information paired to
the Bluetooth
® unit or device is not
recognized correctly. Perform pairing using the following
procedure.  Clear “Mazda” stored in the device.
 Perform pairing again.
Unable to perform pairing The Bluetooth
® function and the
Find Mode/Visible setting *1 on the
device may turn off automatically
after a period of time has elapsed
depending on the device. Check whether the Bluetooth ®
function and the Find Mode/Visible
setting
*1 on the device are turned on
and pairing or reconnect.
Does not connect automatically
when starting the engine
Automatically connects, but then
disconnects suddenly
Disconnects intermittently
The device is in a location in which
radio wave interference can occur
easily, such as inside a bag in a rear
seat, in a rear pocket of a pair of
pants. Move the device to a location in
which radio wave interference is less
likely to occur.
Does not connect automatically
when starting the engine The pairing information is updated
when the device OS is updated.
Perform pairing again.
*1 Setting which detects the existence of a device external to the Bluetoot\
h
® unit

CX-5_8FN1-EA-16L_Edition1.indb 652016/12/12 10:06:36

5–128
Interior Features
Audio Set [Type B (touchscreen)]
Symptom Cause Solution method
Unable to perform pairing The Bluetooth
® function and the
Find Mode/Visible setting *1 on the
device may turn off automatically
after a period of time has elapsed
depending on the device. Check whether the Bluetooth ®
function and the Find Mode/Visible
setting
*1 on the device are turned on
and pairing or reconnect.
Does not connect automatically
when starting the engine
Automatically connects, but then
disconnects suddenly
Disconnects intermittently
The device is in a location in which
radio wave interference can occur
easily, such as inside a bag in a rear
seat, in a rear pocket of a pair of
pants. Move the device to a location in
which radio wave interference is less
likely to occur.
Does not connect automatically
when starting the engine The pairing information is updated
when the device OS is updated. Perform pairing using the following
procedure:
1. Delete the applicable Bluetooth ®
device on the Mazda Connect.
2. Delete “Mazda” from the Bluetooth
® search screen of the
Bluetooth ® device.
3. Perform pairing again.
If pairing is not possible after trying
the procedure, turn off the power
of the Bluetooth
® device once, then
turn it back on. If pairing is still
not possible after this, contact an
Authorized Mazda Dealer or Mazda
Bluetooth
® Hands-Free Customer
Service.
*1 Setting which detects the existence of a device external to the Bluetoot\
h
® unit

CX-5_8FN1-EA-16L_Edition1.indb 1282016/12/12 10:06:59

6–6
Maintenance and Care
Scheduled Maintenance
Remarks:
*1 The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*2 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*4 If this component has been submerged in water, the oil should be replaced.
*5 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


Schedule 2
U.S.A. and Puerto Rico residents - Severe driving conditions maintenance interval
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Spark plugs Replace every 120,000 km (75,000 miles).
Air fi lter
*1 Replace when any equivalent timing of replacing engine oil.
(Max interval: 36 months or 60,000 km (37,500 miles))
Drive belts I I
Engine oil & fi lter Flexible
*2
Replace when wrench indicator light is ON. (Max interval: 12
months or 12,000 km (7,500 miles))
Fixed R R R R R R R R R R R R
Engine coolant
*3 Replace at
fi rst 192,000 km (120,000 miles) or 10 years;
after that, every 96,000 km (60,000 miles) or 5 years.
Engine coolant level I I I I I I I I I I I I
Fuel lines and hoses
*4 I I I
Hoses and tubes for emission
*4 I
Function of all lights I I I I I I I I I I I I
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I I I I I I I I I
Disc brakes I I I I I I
Tire (Rotation) Rotate when any equivalent timing of replacing engine oil.
(Max interval: 8,000 km (5,000 miles))
Tire in fl ation pressure and tire wear I I I I I I I I I I I I
Steering operation and linkages I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*5
CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:07:05

6–7
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Transfer oil
*5
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields Inspect every 72,000 km (45,000 miles) or 5 years.
All locks and hinges L L L L L L L L L L L L
Washer fl uid level I I I I I I I I I I I I
Emergency fl at tire repair kit (if installed)
*6 Inspect annually.
Cabin air fi lter Replace when any equivalent timing of replacing engine oil.
(Max interval:24 months or 48,000 km (30,000 miles))
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
T: Tighten
Remarks:
*1 If the vehicle is operated in very dusty or sandy areas, clean and if ne\
cessary, replace the air fi lter more often
than the recommended intervals.
*2 Engine oil fl exible maintenance is available for U.S.A. and Puerto Rico residents who\
se vehicle is operated
mainly where none of the following conditions apply.
 Extended periods of idling or low-speed operation such as police car, taxi or driving school car
 Driving in dusty conditions If any do apply, follow fi xed maintenance.
The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*3 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*4 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*5 If this component has been submerged in water, the oil should be replaced.
*6 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.




CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:07:05

6–9
Maintenance and Care
Scheduled Maintenance
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*2 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*3 If this component has been submerged in water, the oil should be replaced.
*4 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


CX-5_8FN1-EA-16L_Edition1.indb 92016/12/12 10:07:05

6–11
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers, whichever comes fi
rst
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 10 20 30 40 50 60 70 80 90
100 110 120
CHASSIS and BODY
Brake lines, hoses and connections I I I I I I
Brake and clutch fl uid level I I I I I I I I I
Brake fl uid R R R
Disc brakes I I I I I I I I I I I I
Tire (Rotation) Rotate every 10,000 km
Tire in fl ation pressure and tire wear I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I
Rear differential oil
*3
Transfer oil *3
Driveshaft dust boots I I I I I I
Bolts and nuts on chassis and body T T T T T T
Exhaust system and heat shields I I I I I I
All locks and hinges L L L L L L L L L L L L
Washer fl uid level I I I I I I I I I I I I
Emergency fl at tire repair kit (if installed)
*4 Inspect annually.
AIR CONDITIONER SYSTEM
Cabin air fi lter R R R
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
T: Tighten
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*2 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometer period to ensure long-term reliability.
*3 If this component has been submerged in water, the oil should be replaced.
*4 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


CX-5_8FN1-EA-16L_Edition1.indb 112016/12/12 10:07:05

6–13
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers, whichever comes fi
rst
Months 3 6 9 12 15 18 21 24 27 30 33 36
×1000 km 5 10 15 20 25 30 35 40 45 50 55 60
CHASSIS and BODY
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I I
Brake fl uid R
Disc brakes I I I I I I
Tire (Rotation) Rotate every 10,000 km
Tire in fl ation pressure and tire wear I I I I I I
Steering operation and linkages I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*3
Transfer oil *3
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields I I I
All locks and hinges L L L L L L
Washer fl uid level I I I I I I
Emergency fl at tire repair kit (if installed)
*4 Inspect annually.
AIR CONDITIONER SYSTEM
Cabin air fi lter R R R
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
C: Clean
T: Tighten
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*2 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometer period to ensure long-term reliability.
*3 If this component has been submerged in water, the oil should be replaced.
*4 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.




CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:07:06

6–15
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers, whichever comes fi
rst
Months 39 42 45 48 51 54 57 60 63 66 69 72
×1000 km 65 70 75 80 85 90 95
100 105 110 115 120
CHASSIS and BODY
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I
Brake fl uid R R
Disc brakes I I I I I I
Tire (Rotation) Rotate every 10,000 km
Tire in fl ation pressure and tire wear I I I I I I
Steering operation and linkages I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*3
Transfer oil *3
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields I I I
All locks and hinges L L L L L L
Washer fl uid level I I I I I I
Emergency fl at tire repair kit (if installed)
*4 Inspect annually.
AIR CONDITIONER SYSTEM
Cabin air fi lter R R R
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
C: Clean
T: Tighten
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*2 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometer period to ensure long-term reliability.
*3 If this component has been submerged in water, the oil should be replaced.
*4 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:07:06