tow bar MAZDA MODEL MPV 2004 Owners Manual (in English)

2-18
Essential Safety Equipment
Seats
Form No. 8S06-EA-03H

Removal of Second-Row Seats
The second-row seats can be removed to
create a more comfortable space between
the third-row and front seats. Additional
cargo space is available with the removal
of the second-row seats and stowing of the
third-row seat.
To r e m o v e t h e s e a t
1. Put the buckle in the pocket of the seat
bottom.
2. Lower the head restraint all the way
down.
3. Slide the seat all the way back.
Seat Removal or Installation While
Vehicle is Moving or on a Slope:
Removing or installing the second-
row seats while the vehicle is moving
or on a slope is dangerous. The seats
are heavier than they appear and
could suddenly detach causing
serious injury. Remove or install the
seats with the vehicle parked on a
level surface.
Riding on the Floor Space:
Riding on the floor space created by
the removal of the second-row seat is
dangerous. Sudden braking or a
collision could cause serious injury.
Do not sit or lie in the floor space for
the second-row seat while the vehicle
is moving. Never ride in a vehicle
where you can’t sit in the seat and
wear the seat belt.
Pinching Fingers or Hands:
Placing your hands around the seat
anchors when removing or installing
the second-row seats is dangerous.
You could pinch your hands or
fingers between the seat anchor and
the seat. Hold the edge of the seat
when lowering it into place. Never
place your hands between the seat
anchor and the seat.
WARNING
Lifting the Seat-Anchor Bar:
Lifting the seat-anchor bar without
firmly supporting the seat with your
hand is dangerous. Lifting the seat
unlocks the front clamps
automatically and could cause the
seat to fall. Support the seat firmly
while lifting the seat-anchor bar.
Lowering the seatback without
stowing the seat belt buckle could
damage the seatback.
WARNING
CAUTION
J16R_8S06-EA-03H_Edition1.book Page 18 Wednesday, July 9, 2003 4:19 PM

2-27
Essential Safety Equipment
Seats
Form No. 8S06-EA-03H
7. Remove the support bar from the
pocket.
8. Set the hook on the support bar in the
rear of the seatback.9. Pull the seatback towards the front of
the vehicle until the opposite end of the
support bar hooks onto the anchor loop
in the side trim. Attempt to push the
seatback towards the rear (liftgate) to
make sure the support bar is securely
latched.
Support bar
Pocket
J16R_8S06-EA-03H_Edition1.book Page 27 Wednesday, July 9, 2003 4:19 PM

2-28
Essential Safety Equipment
Seats
Form No. 8S06-EA-03H
To return the third-row seat to the road
position (forward facing)
1. Make sure to stow the shoulder belts
away from the seat bottom as it is
lowered.
2. Detach the support bar by following
the reverse procedure for installation.
3. From inside the vehicle, carefully
lower the seat towards the front until it
locks in place. Attempt to move the
seat forward and backward to make
sure it’s securely locked in place.
4. Reinsert the head restraints.
5. Place the seat belt buckles face up.
6. Fasten the shoulder belts and check
that they are routed properly for
passenger use.All seats can be folded down for use as
beds when the vehicle is safely parked.
Flat Folding
Folded-Flat Seats:
Sitting or lying on seats folded flat is
a dangerous way to ride. During
sudden braking or a collision you
could be thrown around inside the
vehicle and seriously injured. Don’t
ride on seatbacks folded flat.
WARNING
J16R_8S06-EA-03H_Edition1.book Page 28 Wednesday, July 9, 2003 4:19 PM