clock MAZDA MODEL MX-5 RF 2017 (in English) User Guide

5–44
Interior Features
Audio System
Audio Set [Type B/Type C (touchscreen)]
NOTE
The explanation of functions described in this manual may differ from the actual
operation, and the shapes of screens and buttons and the letters and characters
displayed may also differ from the actual appearance.
Additionally, depending on future software updates, the content may successively
change without notice.
Audio Set (Type B/Type C) has three different human interfaces.
 


 Commander switch



 Touch panel



 Voice recognition with steering switch and microphone
Commander switch operation
NOTE
For safety reasons, some operations are disabled while the vehicle is being driven.
Volume dial operation
Volume dial
Press the volume dial to switch the audio MUTE on and off.
Turn the volume dial to adjust the volume. The volume increases by turning the dial
clockwise, and decreases by turning it anticlockwise.
/:A(.'',A'FKVKQPKPFD

5–50
Interior Features
Audio System
Volume/Display/Sound Controls
Volume dial Commander switch Audio control switch
Volume switch
Volume adjustment
Turn the commander switch volume dial.
The volume switch on the steering switch
can also be pressed.
Display setting
Select the
icon on the home screen to
display the Settings screen.
Select the
tab to select the item you
would like to change.
Display OFF/Clock
The centre display can be turned off.
Select
to turn the display off.
When
is
selected the centre display turns off and
the clock is displayed.
The centre display can be turned back on
as follows:
 


 Touch the centre display.



 Operate the commander switch. Daytime/nighttime (Mode) screen
setting
The daytime or nighttime screen can be
selected.
: Switches screen automatically
according to headlight illumination
condition
*1
: Daytime screen setting
: Nighttime screen setting
*1 The display is constantly on daytime
screen when the illumination dimmer is
cancelled.
Brightness adjustment
Adjust the centre display brightness using
the slider.
Contrast adjustment
Adjust the centre display contrast using
the slider.
Display setting reset
All of the screen setting values can be
reset to their initial settings.
1. Select
.
2. Select
.
/:A(.'',A'FKVKQPKPFD

5–67
Interior Features
Audio System
Settings
NOTE
Depending on the grade and speci¿ cation, the screen display may differ.
Select the
icon on the home screen to display the Settings screen.
Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:
Tab Item Function
Display Refer to Volume/Display/Sound Controls on page 5-50 .
Safety Blind Spot Monitoring Volume
Other Refer to Personalisation Features on page
9-10 .
Sound Refer to Volume/Display/Sound Controls on page 5-50 .
Clock Adjust Time Displays the currently set time is displayed.
Press
to advance the hour/minute, and select to move the hour/minute back.
AM/PM can only be selected with the 12-hour
clock display.
GPS Sync Synchronizes with GPS when turned on.
When turned off, the time can be changed from
“Adjust Time”.
Time Format Changes the display between 12 and 24-hour
clock time.
Time Zone Select When it's not synchronized with GPS, select
the region you want to specify.
Daylight Savings Time Turns the daylight saving time setting on/off.
When ON, the time advances 1 hour. When
OFF, it returns to normal time.
Vehicle Rain Sensing Wiper
Door Lock
Other Refer to Personalisation Features on page
9-10 .
Devices Bluetooth
® Refer to Bluetooth ® Preparation on page
5-93 .
Network Management Wi-Fi
™ is used to obtain Navi POI/Real Time
Traf¿ c function (Such as gas prices, weather,
nearest restaurant)
/:A(.'',A'FKVKQPKPFD

5–132
Interior Features
Interior Equipment
Insert the auxiliary key and turn it
clockwise to lock, anticlockwise to unlock.
Lock Unlock
Back Trim Storage Box
Small items can be stored in the back trim
storage box.
(Soft top model)
(Retractable fastback model)
To use the back trim storage box
1. Slide the seat all the way forward and
fold the seatback forward.
Refer to Seat Operation on page
2-5 .
2. Remove the lids.
W h e n ¿ nished, return the seat to its
original position and secure it. After
returning the seat to its original position,
make sure the seat is secured by
attempting to lightly move it forward and
backward.
CAUTION
Do not forcefully push objects into the
back trim storage box. Otherwise, the
box could be damaged.
/:A(.'',A'FKVKQPKPFD

6–40
Maintenance and Care
Owner Maintenance
CAUTION
When removing the lens or lamp unit
using a À athead screwdriver, make
sure that the À athead screwdriver does
not contact the interior terminal. If
theÀ athead screwdriver contacts the
terminal, a short circuit may occur.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights, Running lights (LED type),
Position lights, High-mount brake light,
Brake lights, Tail lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with
the unit. We recommend an Authorised
Mazda Repairer when the replacement is
necessary.
Running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
Removal
Installation
3. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.
4. Turn the socket and bulb assembly
anticlockwise and remove it.
/:A(.'',A'FKVKQPKPFD

6–41
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of the removal procedure.
Front direction indicator lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the centre of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector rearward.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
Side direction indicator lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
/:A(.'',A'FKVKQPKPFD

6–45
Maintenance and Care
Owner Maintenance
*Some models.
9. After the hook is detached, pull out
the rear combination lamp unit in the
direction of the arrow and remove it.
Grommet installation hole Clip
HookRear combination
lamp unit
CAUTION
Carefully pull out the rear combination
lamp unit when removing it from the
body.
The wiring may become damaged if the
rear combination lamp unit is forcefully
pulled out.
10. Turn the socket and bulb assembly
anticlockwise and remove it.
11. Disconnect the bulb from the socket.
12. Install the new bulb in the reverse order
of the removal procedure.
Reverse lights, Rear fog light *
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
anticlockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of the removal procedure.
/:A(.'',A'FKVKQPKPFD

6–46
Maintenance and Care
Owner Maintenance
Number plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the unit by pressing the tab on
the unit with your ¿ nger and pulling the
unit downward.
3. Turn the socket and bulb assembly
anticlockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Replacing Interior Light Bulbs
Overhead light
1. Wrap a small À athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the À athead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of the removal procedure.
/:A(.'',A'FKVKQPKPFD

7–6
If Trouble Arises
Flat Tyre
*Some models.
Jack *
To remove the jack
1. Remove the cover.
Tabs
2. Turn the wing bolt and jack screw
anticlockwise.
Wing bolt
Jack screw
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing back and turn
the wing bolt clockwise to temporarily
tighten it.
2. Turn the jack screw clockwise.
Wing bolt
Jack screw
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suf¿ ciently tightened.
4. Insert the cover tabs and install the
cover.
NOTE
Verify that the cover is securely
installed.
M a i n t e n a n c e
 




 Always keep the jack clean.



 Make sure the moving parts are kept
free from dirt or rust.
 


 Make sure the screw thread is
adequately lubricated.
/:A(.'',A'FKVKQPKPFD

7–9
If Trouble Arises
Flat Tyre
NOTE
The sealant hardens easily and injecting
it will be dif¿ cult under cold weather
conditions (0 °C (32 °F) or below).
Warm the sealant inside the vehicle to
facilitate injection.
7. Remove the cap from the bottle. Screw
on the injection hose with the bottle's
inner cap left on to break the inner cap.
Cap
Injection hose
Tyre sealant
8. Remove the valve cap from the À at
tyre. Press the back of a valve core tool
to the core of the tyre valve and bleed
all the remaining air.
Valve core tool Valve
Valve cap
CAUTION
If there is air remaining in the tyre when
the valve core is removed, the valve core
couldÀ y out. Remove the valve core
carefully.
9. Turn the valve core anticlockwise with
the valve core tool and remove the
valve core.
Valve
Valve core
NOTE
Store the valve core in a place where it
will not get dirty.
10. Insert the injection hose into the valve.
Valve
Injection hose
/:A(.'',A'FKVKQPKPFD