light MAZDA MODEL MX-5 RF 2017 (in English) Workshop Manual

3–41
Before Driving
Convertible Top (Soft Top)
7. Move the convertible top rearward and
fold it while pressing the rear glass
lightly with your hand.
8. With the back end of the convertible
top pressed, press the front end until a
latch sound is heard.
Lightly rock the retracted convertible
top to make sure it is securely locked.
Raising the Convertible Top
1. Make sure the parking brake is applied.
2. If the engine is running, turn it off.
3. Pull up the unlock lever to disengage
the lock.
Unlock Lever
4. Standing outside of the vehicle, hold
the convertible top along the front edge
and pull it towards the vehicle front.
Front edge
/:A(.'',A'FKVKQPKPFD

3–48
Before Driving
Convertible Top (Retractable Fastback)
Operation Indication
Operation Indicator Light
When illuminated
This indicates that the roof is only partially open.
When À ashing
This indicates that the roof is being open/closed. (During switch operation)
When not illuminated
This indicates that the roof is open/closed fully.
NOTE
If the operation indicator light À ashes quickly, there may be a system malfunction.
Consult an Authorised Mazda Repairer.
/:A(.'',A'FKVKQPKPFD

3–51
Before Driving
Convertible Top (Retractable Fastback)
Opening the Roof
1. Park on a hard, level surface off the
right-of-way and ¿ rmly set the parking
brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Neutral.
3. Apply the parking brake with the brake
pedal depressed.
4. Start the Engine.
NOTE
Do not open/close the roof with the
engine stopped. Otherwise the vehicle's
battery power could be depleted.
5. Continue pressing the retractable
fastback switch in the open direction
until the roof is completely open.
NOTE
  If the retractable fastback switch
is pressed in the open direction, a
warning beep sounds.
  If the windows are closed, the
windows automatically open partially
when the rear roof opens.
 After the rear roof is opened and
the retractable fastback switch is
continuously pressed in the open
direction, the power windows close
completely.
 Once you remove your hand from
the switch, the power windows do
not close even if it is operated again.
If this happens, completely close
the power windows using the power
window switch.
  The roof keeps opening and the
operation indicator light À ashes
while the retractable fastback switch
is pressed in the open direction.
  If the switch is released while the
roof is opening, the roof stops
opening. If the switch is pressed in
the open direction again, the roof
resumes opening.
  When the operation is ¿ nished, a
beep sound is heard and the operation
indicator light turns off.
  When the roof is half-open, the front
roof resumes opening after the rear
roof is completely open.
/:A(.'',A'FKVKQPKPFD

3–52
Before Driving
Convertible Top (Retractable Fastback)
Closing the Roof
1. Park on a hard, level surface off the
right-of-way and ¿ rmly set the parking
brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Neutral.
3. Apply the parking brake with the brake
pedal depressed.
4. Start the Engine.
NOTE
Do not open/close the roof with the
engine stopped. Otherwise the vehicle's
battery power could be depleted.
5. Slightly slide the seats back if they are
in the foremost position.
6. Continue pressing the retractable
fastback switch in the close direction
until the rear roof is completely closed.
NOTE
  If the retractable fastback switch
is pressed in the close direction, a
warning beep sounds.
  If the windows are closed, the
windows automatically open partially
when the rear roof opens.
 After the rear roof is closed and
the retractable fastback switch is
continuously pressed in the close
direction, the power windows close
completely.
 Once you remove your hand from
the switch, the power windows do
not close even if it is operated again.
If this happens, completely close
the power windows using the power
window switch.
  The roof keeps closing and the
operation indicator light À ashes
while the retractable fastback switch
is pressed in the close direction.
  If the switch is released while the
roof is closing, the roof stops closing.
If the switch is pressed in the close
direction again, the roof resumes
closing.
  When the operation is ¿ nished, a
beep sound is heard and the operation
indicator light turns off.
/:A(.'',A'FKVKQPKPFD

3–53
Before Driving
Security System
M o d i¿ cation and Add-On
Equipment
Mazda cannot guarantee the immobilizer
and the theft-deterrent systems' operation
if the system has been modi¿ ed or if any
add-on equipment has been installed.
CAUTION
To avoid damage to the vehicle, do not
modify the system or install any add-on
equipment to the immobilizer and the
theft-deterrent systems or the vehicle.
Immobilizer System
The immobilizer system allows the
engine to start only with a key the system
recognises.
If someone attempts to start the engine
with an unrecognised key, the engine
will not start, thereby helping to prevent
vehicle theft.
If you have a problem with the
immobilizer system or the key, consult an
Authorised Mazda Repairer.
CAUTION
  Changes or modi¿ cations not
expressly approved by the party
responsible for compliance could
void the user's authority to operate
the equipment.
  To avoid damage to the key, do not:




 Drop the key.



 Get the key wet.



 Expose the key to any kind of
magnetic¿ eld.




 Expose the key to high
temperatures on places such as the
instrument panel or bonnet, under
direct sunlight.
 
 If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or À ashing,
the system may have a malfunction.
Consult an Authorised Mazda
Repairer.
/:A(.'',A'FKVKQPKPFD

3–54
Before Driving
Security System
NOTE
  The keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining a replacement
key requires some waiting time.
They are only available through an
Authorised Mazda Repairer.
  Always keep a spare key in case one
is lost. If a key is lost, consult an
Authorised Mazda Repairer as soon
as possible.
  If you lose a key, an Authorised
Mazda Repairer will reset the
electronic codes of your remaining
keys and immobilizer system.
Bring all the remaining keys to an
Authorised Mazda Repairer to reset.
 Starting the vehicle with a key that
has not been reset is not possible.
Operation
NOTE
  The engine may not start and security
indicator light may illuminate or
À ash if the key is placed in an area
where it is dif¿ cult for the system
to detect the signal, such as on the
instrument panel. Move the key to
a location within the signal range,
switch the ignition off, and then
restart the engine.
  Signals from a TV or radio station,
or from a transceiver or mobile
telephone could interfere with your
immobilizer system. If you are using
the proper key and the engine fails
to start, check the security indicator
light.
Arming
The system is armed when the ignition is
switched from ON to off.
The security indicator light in the
instrument cluster À ashes every 2 seconds
until the system is disarmed.
Disarming
The system is disarmed when the
ignition is switched ON with the correct
programmed key. The security indicator
light illuminates for about 3 seconds and
then turns off. If the engine does not start
with the correct key, and the security
indicator light remains illuminated or
À ashing, try the following:
Make sure the key is within the
operational range for signal transmission.
Switch the ignition off, and then restart
the engine. If the engine does not start
after 3 or more tries, contact an Authorised
Mazda Repairer.
NOTE
  If the security indicator light À ashes
continuously while you are driving,
do not shut off the engine. Go to an
Authorised Mazda Repairer and have
it checked. If the engine is shut off
while the indicator light is À ashing,
you will not be able to restart it.
  Because the electronic codes are
reset when the immobilizer system
is repaired, the keys are needed.
Make sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
/:A(.'',A'FKVKQPKPFD

3–55
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and À ashing the
hazard warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.
The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
 
 Do not hang clothing or objects from
a head restraint.
  Return the sunvisors to their original
positions.
  Do not blind the intrusion sensor by
covering it or placing objects over it.
  Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
  Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
  Do not install seats that are not
Mazda genuine products.
  To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

Intrusion sensor and
intrusion sensor bezel
/:A(.'',A'FKVKQPKPFD

3–56
Before Driving
Security System
Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights À ash for about
30 seconds when the system is triggered
by any one of the following:
 


 Unlocking a door with an inside door-
lock knob.
 


 Forcing open a door, the bonnet or the
boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
 


(With the intrusion sensor)
 The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
 


(With the intrusion sensor)
 Disconnecting the battery terminal (the
hazard warning lights do not À ash).
The system will be triggered about 10
times.
NOTE
  The boot lid does not open while the
theft-deterrent system is operating.
  If the battery goes dead while the
theft-deterrent system is armed,
the siren/horn will activate and the
hazard warning lights will À ash when
the battery is charged or replaced.
How to Arm the System
1. Close the windows and the convertible
top securely.
NOTE
(With the intrusion sensor)
The intrusion sensor function can be
armed only when the convertible top is
closed.
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion Sensor
(With Intrusion Sensor) on page 3-57 .
2. Switch the ignition OFF.
3. Make sure the bonnet, convertible top,
the doors, and the boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will À ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument cluster À ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
/:A(.'',A'FKVKQPKPFD

3–57
Before Driving
Security System
NOTE
  The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors, the
boot lid and the bonnet closed.
 Refer to Transmitter on page 3-5 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door.



 Opening the bonnet.



 Switching the ignition ON.

 To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
 


 Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
 


 Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
 


 Hanging small objects/accessories in the
vehicle, or placing other items which
can move easily inside the vehicle.
 


 Parking in an area where there is strong
vibration or loud noise.
 


 When using a high pressure or automatic
car wash.
 


 Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
 


 Doors are locked with a window left
open.
 


 An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the boot lid remains
closed for 30 seconds, both doors and
the boot lid automatically re-lock and
the theft deterrent system arms even if
a window or the convertible top is left
open.
/:A(.'',A'FKVKQPKPFD

3–58
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will À ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.
The hazard warning lights will À ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will À ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric boot lid opener
while the key is being carried.
The hazard warning lights will À ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the console box.
Mazda recommends that you af¿ x it to the
lower rear corner of a front door window.
/:A(.'',A'FKVKQPKPFD