wiring MAZDA PROTEGE 1992 Owner's Manual

TROUBLESHOOTING GUIDE
17 HESITATES/STUMBLES ON ACCELERATION
bESCRIP-
*Flat spot occurs just after accelerator depressed or mild jerking occurs during acceleration
‘ION TROUBLESHOOTING HINTS]
0 Air/Fuel mixture becomes lean when depressing accelerator l Fuel injection control malfunction
(Correction for accelerating condition)
*Air leakage
l Fuel line pressure decreases l Spark advance control malfunction TEP INSPECTION ACTION
1 Check if “00” is displayed on Self-Diagnosis Yes Go to next step
Checker with ignition switch ON W page F-82 ’ No
Service Code No. displayed
SYSTEM SELECT: 1 Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
W: SELF TEST Check ECU terminal IF voltage CT= page F-150
Specification: Battery voltage
(Ignition switch ON) c3 If OK, replace ECU c? page F-149 * If not OK, check wiring between
ECU and Self-Diagnosis Checker Vacuum: More than 450 mmHg (17.7 InHg)
tern components
Replace air cleaner element 4
Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especiaily 2L
ATX... Especially lT, 2F, and 21 w page F-150
No Check for cause cp page F-151
5
Check if throttle linkage is correctly installed and
Yes Go to next step
operates freely w page F-l 14 ~~
Correct, clean, or replace as required
any binding or damaged linkage and
adjust cable deflection at throttle body w page F-l 14
6
Check continuity between throttle sensor termi- Yes Go to next step
nals IDL and E w page F-189
MTX
A-I-X 1
J E
IDL
Clearance between throttle
lever and stopper Continuity
MTX 0.1 mm (0.004 in) Yes
1 .Omm (0.039 in) No
ATX 0.1 mm (0.004 in)
Yes
0.6mm (0.024 in) No
No Adjust w page F-189
F-57

TROUBLESHOOTING GUIDE
18 SURGES WHILE CRUISING
DESCRIP- *Unexpected change in engine speed which is usually repetitive
TION [TROUBLESHOOTING HINTS]
@ Air/Fuel mixture too lean
@ Misfire
3 Poor connection in wiring harness
SYSTEM SELECT:
1 “88” flashes
Check ECU terminal 1F voltage CT= page F-150
Specification: Battery voltage
(Ignition switch ON)
+ If OK, replace ECU w page F-149 4 If not OK, check wiring between
ECU and Self-Diagnosis Checker
check sequence) w page F-106
heck ECU terminal ID voltage CT page F-150
oxygen sensor
F-59

TROUBLESHOOTING GUIDE F
9 LACK OF POWER
_-- --
L L -
ESCRIP- *Performance poor under load when throttle valve wide open
ION *Reduced maximum speed
* Idle condition normal
VtOUBLESHOOTlNG HINTS]
) Factors other than engine malfunction
*Clutch slipping
* ATX slipping
l Brake dragging l Low tire pressure
l Incorrect We size l Overloaded
‘, Low intake air amount @ Air/Fuel mixture too lean
l Fuel line pressure decreases l Fuel injection malfunction
@ Poor ignition
@ Low engine compression
@ Alcohol blended fuel used
l Throttle valve not open fully
*Clogged intake air system
l Low tire pressure CY Section H
CY Section K
cz7 Section P
c7 Section Q
w page F-l 14
CT= page F-l 12
Checker with ignition switch ON
w page F-83
rminal 1F voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
* If OK, replace ECU w page F-149
c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
Ignition timing (BTDC)
l BP DOHC : 9*-l lo l BP SOHC
: 4O-8O 4 If advances, go to next step
* If not advance, check ECU terminal
w page F-150
F-61

TROUBLESHOOTING GUIDE F
20 POOR ACCELERATION
DESCRIP- l Performance poor while accelerating
TION l idle condition normal [TROUBLESHOOTING HINTS)
3 Factors other than engine malfunction @ Air/Fuel mixture too lean
*Clutch slipping l Fuel line pressure decreases l ATX slipping l Fuel injection malfunction
l Brake dragging @ Poor ignition l Low tire pressure
@ Low engine compression
l Incorrect tire size @ Alcohol blended fuel used l Over-loaded
3 Low intake arr amount
*Throttle valve not open fully
*Clogging in intake air system
Check factors other than engine CT Section H
c7 Section
P
ing accelerator fully w page F-l 14
w page F-l 12
Checker with ignition switch ON w page F-83
rminal 1 F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST c3 If OK, replace ECU w page F-149 r;3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
Clearance between throttle
lever and stopper
0.1 mm (0.004 in)
l.Omm (0.039 in)
O.lmm (0.004 in)
0.6mm (0.024 in)

TROUBLESHOOTING GUIDE F
21 RUNS ROUGH ON DECELERATION/BACKFIRE
IESCRIP.
*Engine runs rough while decelerating and abnormal combustion occurs in exhaust system
MON l Transaxle in normal condition TROUBLESHOOTING HINTS]
1) Arr/Fuel mixture too rich
l Arr cleaner element clogged
l Fuel injection control malfunctron
(Fuel cut control)
l Injector fuel leakage
*Throttle sensor (IDL terminal) malfunction
l Dashpot malfunctron
er with ignition switch ON
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
+ If OK, replace ECU w page F-149 6 If not OK, check wiring between
ECU and Self-Diagnosis Checker
----~
Check for cause (Refer to specified
check sequence) w page F-106
SELECT SW: A Vacuum: More than 450 mmHg (17.7 inHg)
tern components
4 Check if air cleaner element is clean Yes
Go to next step w page F-79
No
Replace air cleaner element
5 Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especially lN, 2A, 2U and 2V
ATX... Especially lT, 3A, 3U and 3V CT page F-150
No Check for cause c=i‘ page F-151
F-69

22 KNOCKING
DESCRIP- *Abnormal combustion accompanied by audible “pinging” noise
I-ION
[TROUBLESHOOTING HINTS]
3 Incorrect ignition timing (Too advanced)
@ Air/Fuel mixture too lean
3 Carbon deposits in cylinder
*Fuel injection amount not correct
3 Overheating
l Fuel line pressure decreases while accelerating
TEP INSPECTION
ACTION
1 Connect System Selector to diagnosis connector
Yes Go to next step
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up
CT page F-79
Ignition timing (BTDC)
l BP DOHC : go-1 1 o l BP SOHC : 4”-6O
’ B6 No
Adjust a page F-79
2 Check if “00” is displayed on Self-Diagnosis
Yes Go to next step
Checker with ignition switch ON
W page F-62
No
Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU w page F-149
W: SELF TEST c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check for correct intake manifold vacuum at idle
Yes Go to next step
VaCUUm: More than 450 mmHg (17.7 inHg) No
Check for air leakage of intake air sys-
tem components
4
Check for correct engine compression
Yes Go to next step
w page Bl-10
B2-10
Engine compression (Minimum):
l BP DOHC
883 kPa (9.0 kg/cm’, 128 psi)-300 rpm
l BP SOHC
834 kPa (8.5 kg/cm*, 121 psi)300 rpm
l B6
932 kPa (9.5 kg/cm’, 135 psi)300 rpm No High compression
Check engine condition CI page 81-10
62-l 0 l Carbon deposits
F-71

TROUBLESHOOTING GUIDE F
23 FUEL ODOR
DESCRIP-
*Gasoline odor in cabin
TION [TROUBLESHOOTING HINTS]
@ Poor connection or damaged at fuel system or evaporative emission control system
@ Charcoal canister overflow due to evaporative emission control System malfUnCtiOn
Check for cause (Refer to specified Specification: Battery voltage
(Ignltlon switch ON)
c3 If OK, replace ECU r;+ page F-149 c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
control) with engine running and throttle valve
opened (Neutral switch connector disconnected)
eck if vacuum is felt
s
23UOFX-029
F-73

TROUBLESHOOTING GUIDE F
26 POOR FUEL ECONOMY
DESCRIP-
l Fuel economy unsatisfactory TION
[TROUBLESHOOTING HINTS]
While fuel consumption is drastically increased by city driving, short-run operation, stop and go driving, extended winter
warm-up periods, etc., as opposed to “trip” mileage, an attempt should be made to determine these factors when con-
fronted with “poor mileage” conditions. However, since the operator is not always at fault, the following is offered.
@II Operator depressing accelerator more than usual due to
@ Air/Fuel mixture too rich
low engine power
l Poor ignition *High fuel line pressure
@ Alcohol blended fuel used
*Low intake air amount
l Electronic spark advance control system malfunction @ High vehicle load l Low tire pressure
*Clutch slipping/ATX slipping l Incorrect tire size l Exhaust component restricted l Brake dragging ;TEP
INSPECTION ACTION
1
Check factors other than engine Yes
Go to next step
l Low tire pressure = Section Q 9 Unrecommended tire srze v Section Q l Clutch slipping w Section H l Brake dragging No
0 Section P Repair
l Exhaust component restricted cz= page F-136
2
Check if air hoses are connected correctly - Yes
Go to next step CI page F-109
No
Repair 3
Check if “00” IS displayed on Self-Diagnosis
Yes
Checker with ignition switch ON Go to next step W page F-82 No
SYSTEM SELECT: 1 Service Code No. displayed Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
* If OK, replace ECU CT= page F-149 e If not OK, check wiring between
ECU and Self-Diagnosis Checker 4
Check for correct intake manifold vacuum at idle
Yes Go to next step Vacuum: More than 450 mmHg (17.7 inHg) No
Check for air leakage at intake air sys-
tem components 5
Check if air cleaner element is clean Yes
Go to next step CT= page F-79
No
Replace air cleaner element
F-75

TROUBLESHOOTING GUIDE
27 MIL ALWAYS ON
DESCRIP- *Self-Diagnosis Checker does not indicate Malfunction Code No. but MIL always ON
TION
[TROUBLESHOOTING HINTS]
*Short circuit in wiring harness
l ECU malfunction
iTEF 1
1
-
s
Disconnect (Y/B) wire from ECU and check if
MIL goes off
‘YIB
ATX YIB
INSPECTION ACTION
Yes Replace ECU CT page F-149
No Check for short circuit in wiring be-
tween instrument cluster and ECU
23UOFX-042
28
MIL NEVER ON
IESCRIP- *Self-Diagnosis Checker indicates Malfunction Code No. of input device but MIL never ON
RON *Other indicator and warning lamps OK
:TROUBLESHOOTING HINTS]
b Bulb burned
‘Open circuit in wiring harness
m ECU malfunction
TEP INSPECTION
ACTION
1 Ground (Y/B) wire at ECU with jumper wire and
Yes Check connection of ECU connector
check if MIL comes on
MTX e If OK, replace ECU w page F-149
I- i -!~ !r--~r’:~;-‘;- --~_:- ,
1 i r 1 1 1 ;-.:,~;~$~& {-;&# ,$&]j 4 If not OK, repair ECU connector
! No
Check if bulb is OK
ATX 13 If OK, repair (Y/B) wire between
ECU and instrument cluster
e If not OK, replace bulb CT page T-83
23UOFX-043
29 A/C DOES NOT WORK
DESCRIP- *Blower fan operates but magnet clutch does not operate
TION
[TROUBLESHOOTING HINTS]
*Open or short circuit in wiring harness
*A/C relay, A/C switch, or magnetic clutch malfunction
l ECU malfunction
TEP/ INSPECTION ACTION
1 1 Check ECU
terminal 10 (MTX) 10 (ATX) voltage 1
Yes Check ECU terminal 1 J (MTX) 1 L (ATX)
OK
CT= page F-152
MTX
T7J++!;i”-
L
ATX
No voltage OK
CT page F-152
1-3 If OK, check A/C system
c3- page U-30
~3 If not OK, replace ECU CT page F-149
Check for cause w page F-153
F-77

SELF-DIAGNOSIS FUNCTION F
PREPARATION
SST
49 6019 9AO
System Selector For
diagnosis 49 HO18 9Al
Self-Diagnosis
Checker For
diagnosis
SERVICE CODE NUMBER
Inspection Procedure
1. Connect the SST to the diagnosis connector.
2. Set switch @to position 1.
3. Set TEST SW to SELF-TEST position.
23UOFX-048
03UOFX.059
I
4. Connect the SST to the System Selector and a ground
5. Set the select switch to position A.
6. Turn the ignition switch to ON.
7. Verify that 88 flashes on the digital display and the buzzer
sounds for 3 sec. after turning the ignition switch ON.
8. If 88 does not flash, check the main relay (FUEL INJ relay)
(Refer to page F-172) power supply circuit, and diagno-
sis connector wiring.
9. If 88 flashes and the buzzer sounds continuously for more
than 20 sec., check for a short circuit between the engine
control unit terminal 1 F and the diagnosis connector. Re-
place the engine control unit if necessary and perform Steps
3 and 7 again.
23UOFX-049 IO. Note any code numbers and check for the causes by refer-
ring to the check sequences shown on pages F-88
through F-103. Repair as necessary.
Note
l Cancel the code numbers by performing the after-
repair procedure following repairs.
(Refer to page F-104.)
I 23UOFX-050
F--83