tow MERCEDES-BENZ C-Class COUPE 2017 CL205 Repair Manual

!Do not use the towing eye for recovery. This
could damage the vehicle. If in doubt, have
the vehicle recovered using acrane.
!When towing, pull aways lowly and
smoothly. If the tractive power is too high, the
vehicles could be damaged.
!Shift the automatic transmission to Nand
do not open the driver's or front passenger's
door during towing. The automatic transmis-
sion may otherwise shift to position P,which
could damage the transmission.
!Do not tow with sling-type equipment. This
could damage the vehicle.
!The vehicle can be towed amaximum of
30 miles (50km). The towing speed of 30 mph (50 km/h) must not be exceeded.
If the vehicle has to be towed more than
30 miles (50km), the entire vehicle must be
raised and transported.
It is better to have the vehicle transported than
to have it towed away.
If the vehicle has suffered transmission damage,
have it transported on atransporter or trailer.
The automatic transmission must be in position N when the vehicle is being towed. If the auto-
matic transmission cannot be shifted to position
N,h ave the vehicle transported on atransporter
or trailer.
The battery must be connected and charged.
Otherwise, you:
Rcannot turn the SmartKey to position 2in the
ignition lock
Rcannot release the electric parking brake
Rcannot shift the automatic transmission to
position N
Disarm the automatic locking feature before the vehicle is towed (
Ypage 81). You could other-
wise be locked out when pushing or towing the
vehicle.
Installing/removing the towing eye
Installingt he towing eye
The brackets for the screw-in towing eye are
located in the bumpers. They are at the rear and
at the front,u nder covers:.
XRemove the towing eye from the vehicle tool
kit (Ypage 300).
XPress the mark on cover :inwards and
remove.
XScrew in the towing eye clockwise as far as it will go and tighten it.
Removing the towing eye
XUnscrew and remove the towing eye.
XAttach cover :to the bumper and press until
it engages.
XPut the towing eye back into the vehicle tool
kit.
Towing the vehiclew ith the rear axle
raised
Only vehicles without 4MATIC can be towed
with the rear axle raised.
!Vehicles with 4MATIC must not be towed
with either the front or the rear axle raised, as doing so will damage the transmission.
Vehicles with 4MATIC may either be towed away
with both axles on the ground or be loadedu p
and transported.
Towing and tow-starting311
Breakdown assistance
Z

!Vehicles with automatic transmission must
not be towed with the rear axle raised. The
vehicle/trailer combination may otherwise
swerve or even roll over.
Towing avehiclew ith both axles on
the ground
The automatic transmission automaticallys hifts
to position Pwhen you open the driver's or front-
passenger door or when you remove the Smart-
Key from the ignition lock. In order to ensure
that the automatic transmission stays in posi-
tion Nwhen towing the vehicle, you must
observe the following points:
XMake sure that the vehicle is stationary.
XTurn the SmartKey to position 2in the ignition
lock.
XDepress and hold the brake pedal.
XShift the automatic transmission to position
N.
XLeave the SmartKey in position 2in the igni-
tion lock.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch on the hazard warning lamps
(Ypage 112).
In order to signal achange of direction when
towing the vehicle with the hazard warning
lamps switched on, use the combination switch
as usual. In this case, only the indicator lamps
for the direction of travel flash. After resetting
the combination switch, the hazard warning
lamp starts flashing again.
Transporting the vehicle
4MATIC vehicles/vehiclesw ith auto-
matic transmission
!When the vehicle is loadedf or transport, the
front and rear axles must be stationary and on the same transportation vehicle. Positioning
over the connection point of the transport
vehicle is not permitted. The drive train may
otherwise be damaged.
All vehicles
!You may only secure the vehicle by the
wheels, not by parts of the vehicle such as
axle or steering components. Otherwise, the
vehicle could be damaged.
The towing eye can be used to pull the vehicle
onto atrailer or transporter for transporting pur-
poses.
XTurn the SmartKey to position 2in the ignition
lock.
XShift the automatic transmission to position
N.
As soon as the vehicleh as been loaded:
XPrevent the vehicle from rolling awayb y
applying the electric parking brake.
XShift the automatic transmission to posi-
tion P.
XTurn the SmartKey to position 0in the ignition
lock and remove it.
XSecure the vehicle.
312Towing and tow-starting
Breakdown assistance

Noteson4 MATIC vehicles
!
Vehicle swith4 MATIC must not be towed
with eithe rthe front or the rea raxler aised, as
doing so will damage the transmission.
Vehicle swith4 MATIC maye ithe rbet owed away
with both axles on the ground or be loaded up
and transported.
If the vehicle' stransmission, front, or rea raxlei s
damaged, have the vehicl etransporte dona
truck or trailer.
In the even tofdamagetot he electrical sys-
tem: if the battery is defective, the automatic
transmission will be locked in position P.Tos hift
the automatic transmission to position N,you
must provide powe rtothe vehicle' selectrical
syste mint he same wa yaswhenj ump-starting
(
Ypage 308).
Have the vehicl etransporte donatransporte ror
trailer.
Tow-startin g(em ergency engine
starting)
!
Vehicle switha utomatic transmission must
not be tow-started .You could otherwis edam -
ag et he automatic transmission.
iYouc an find information on "Jump-starting"
under (Ypage 308).
Fuses
Important safety notes
GWARNING
If yo umanipulate or bridg eafaulty fuse or if
yo ur eplace it with afusew ithah igheramper -
age, the electric cable scould be overloaded.
This could resul tinafire. There is ariskofa n
accident and injury.
Alway sreplace faulty fusesw itht he specified
new fusesh avingthe correc tamperage.
Blown fusesm ustber eplaced with fusesoft he
same rating ,which yo ucan recognize by the
color and value. Th efuser ating sarelistedint he
fuse allocatio nchart.
Th efus ea lloc atio nchart is on the fuse bo xinthe
trunk (
Ypage 315). If
an ewly inserte dfusea lsob lows ,havet he
cause traced and rectifie dataqualified special-
is tw orkshop ,e.g.ana uthorized Mercedes-Benz
Center.
!Onl yusefusest hath aveb eena pproved for
Mercedes-Benz vehicles and which have the
correc tfus er ating for the systemc oncerned.
Otherwise, components or systems could be
damaged.
!Make sure tha tnomoisture can ente rthe
fuse bo xwhent he cover is open.
!When closing the cover, make sure tha titis
lying correctly on the fuse box. Moistur eseep-
ing in or dirt could otherwis eimpair theope
r-
ation of the fuses.
Th ef uses in your vehicl eserve to close down
faulty circuits .Ifafuse blows, al lthe compo-
nents on the circuit and their functions stop
operating.
Before changin gafuse
Observe the important safety notes
(Ypage 313)
XSwitch off the engine.
XSwitch off al lelectrica lconsumers.
XSecure the vehicl eagain st rolling away
(Ypage 152).
XRemov ethe SmartKeyf romthe ignition lock.
or, in vehicles with KEYLESS-GOs tart-function
or KEYLESS ‑GO
XOpen the driver's door.
Theo n-board electronics now have status 0.
This is the same as the SmartKeyh avingbeen
removed.
Th ed river’s door can be closeda gain.
All indicator lamps in the instrumen tcluster
must be off.
Th ef uses arel oc ated in variou sfuseb oxes:
RFuse bo xonthe driver's side of the dashboard
RFuse bo xinthe front-passenge rfootwell
RFuse bo xinthe engine compartment on the
driver's side
RFuse bo xunder the trunk floo ronthe right-
hand side of the vehicle, when viewed in the
directio noftravel
Fuses313
Breakdow nassistance
Z

Dashboardfuseb ox
!
Do no tuse ap ointe dobjec tsuc hasas crew -
driver to ope nthe cover in th edashboard. You
could damage th edashboar dorthecover .
XOpenthe driver's door.
XTo open: pull out cover :slightly at th ebot-
to mint hedirection of arrow =.
XFold cover:outward sinthedirection of
arrow ;.
XTo close :fold in cover :until it engages.
Fus ebox in th efront-passenger foot -
well
XOpe nthe front-passenger door.
XTo open: fold cover :out toward sthe rea r
and remov eit.
XTo close :clip in cover :at th erear.
XFold cover :forwards until it engages.
Fus ebox in th eengin ecompartment
GWARNING
Whe nthe hoo diso pena nd th ewindshield
wipers are set in motion ,you can be injured by
th ew iperlinkage. There is ariskofi njury.
Always switch of fthe windshield wipers and
th ei gnition befor eopening th ehood.
XOpe nthe hoo d(Ypage 287).
XTo open: press safet yclips : on th ecover
together .
XRemovefuseb ox cover ;upwards.
XUse adry clot htoremov eany moisture from
th ef useb ox.
XLoosen screw s=,f oldupf useb ox lid ?and
remov eit.
XTo close :chec kwhether th eseal is posi-
tioned correctl yint he lid?.
XInser tlid ? into th ebracket at th erearoft he
fus eb ox.
XFold down lid ?of th efuseb ox and tighten
screw s=.
XInser tcover ; on bot hsides and engage
safet yclips :.
XClos ethe hood.
314Fuses
Breakdown assistance

Information on the message display can be
found in the "Checking the tire pressure elec-
tronically"section (
Ypage 325).
Important safety notes
GWARNING
Each tire, including the spare (if provided),
shoul dbec hecked at least once every two
weeks when cold and inflated to the pressure recommended by the vehicle manufacturer
on the Tire and Loading Information placard
on the driver's door B-pillaro rthe tire pres-
sure label on the inside of the fuel fillerf lap. If
you rvehicle has tires of adifferent size than
the size indicated on the Tire and Loading
Information placard or, if available, the tire
pressure label, you shoul ddetermine the
proper tire pressure for those tires.
As an adde dsafety feature, you rvehicle has
been equipped with atire pressure monitoring
system (TPMS) that illuminates alow tire pres-
sure telltal ewhen one or more of you rtires
are significantly underinflated. Accordingly,
when the low tire pressure telltal elights up,
you shoul dstop and check you rtires as soon
as possible, and inflate them to the proper
pressure. Driving on asignificantly underin-
flated tire cause sthe tire to overheata nd can
leadtot ire failure.
Underinflation also reduces fuel efficiency
and tire tread life, and may affect the vehicle's
handling and stopping ability. Please note that the TPMS is not asubstitute for proper tire
maintenance, and it is the driver's responsi-
bility to maintain correct tire pressure, even if
underinflation has not reached the level to
trigger illuminatio nofthe TPMS low tire pres-
sure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the sys-
tem detects amalfunction, the warning lamp
wil lflash for approximately aminute and then
remain continuously illuminated .This
sequence wil lberepeated every time the vehi-
cle is started as long as the malfunction
exists. When the malfunction indicator is illu-
minated, the system may not be abl etodetect
or signal low tire pressure as intended.
TPMS malfunctions may occur for avariety of
reasons, including the installation of incom-
patibl ereplacement or alternate tires or
wheel sonthe vehicle that prevent the TPMS
from functioning properly. Alway scheck the
TPMS malfunction telltal eafter replacing one
or more tires or wheel sonyourv ehicle to
ensure that the replacement or alternate Tires
and wheelsa llow the TPMS to continue to
function properly.
It is the driver's responsibility to set the tire
pressure to that recommended for cold tires
which is suitable for the operating situation
(
Ypage 319). Note that the correct tire pressure
for the current operating situation must first be
taught-in to the tire pressure monitor. If there is
as ubstantial loss of pressure, the warning
threshold for the warning messag eisaligned to
the reference values taught-in. Restart the tire
pressure monitor after adjusting the pressure of
the cold tires (
Ypage 325). The current pres-
sures are saved as new reference values. As a
result, awarning messag ewillappear if the tire
pressure drops significantly.
The tire pressure monitor does not warn you of
an incorrectly set tire pressure. Observe the
notes on the recommended tire pressure
(
Ypage 319).
The tire pressure monitor is not abl etowarn you
of as udden loss of pressure, e.g. if the tire is
penetrated by aforeign object. In the event of a
su

dden loss of pressure, bring the vehicle to a
halt by braking carefully. Avoid abrupt steering
movements.
324Tire pressure
Wheelsa nd tires

XClean thewheel and wheel hub contact sur-
faces.
XSlid ethe wheel to bemounte dontot he align-
men tbolt and push iton.
XTighte nthe wheel boltsuntilthey are finger-
tight.
XUnscrew th ealignmen tbolt.
XTighte nthe last wheel boltuntil it is finger-
tight.
Lowering th evehicle
GWAR NING
The wheelsc ouldwork looseift hewheel nuts
and boltsare no ttightened to th especifie d
tightening torque. Thereisar iskofa cciden t.
Hav ethe tightening torque immediately
checked at aqualified specialist workshop
after awheel ischanged.
XTurn th ecrank of th ejackc ounter-clock wise
unt ilth ev ehicle is once again standing firmly
on th eground.
XPlacet hejacktoo neside.
XTighte nthe wheel boltsevenly inac rosswise
pattern inthes equenc eindicated (: toA). The specifie
dtightening torque is 96lb-ft
(1 30 Nm) .
XTurn th ejackb ack to its initial position.
XStow th ejac ka nd th erestoft hevehicle tools
in thet runk again.
XMercedes-AM Gvehicles and vehicles
with AMG equipment: insert thecover into
th eo uter sill.
XCheckt hetirep ressureoft henewly mounted
wheel and adjust it if necessary.
Observ ethe recommended tir epressure
(
Ypage 319).
When you are driving withthe collapsible spare
wheel mounte d,thet irep ressurel oss warning
system or th etirep ressurem onitorcanno tfunc-
tio nr eliably. Only restartthe tirep ressurel oss
warning system or tir epressurem onitorwhen
th ed efective wheel has been replace dwitha
ne ww heel.
Vehicles with atirep ressure control sys-
tem: all installed wheelsm ust be equippedwith
functioning sensors.
Wheel-tire combination
You can ask for informatio nregardin gpermitted
wheel-tire co mbinations at an authorized
Mercedes-Ben zCenter.
!For safety reasons, Mercedes-Ben zrecom-
men dsthat you only use tires and wheels
whic hhave been approvedbyM ercedes-Benz
specifically for your vehicle.
Theset ires have been specially adapted for
use witht hecontrol systems ,suchasA BSor
ESP
®,a nd are marke dasfollows:
RMO= Mercedes-Ben zOriginal
RMOE = Mercedes-Ben zOriginal Extended
(tires featurin grun-flat characteristics)
RMO1 = Mercedes-Ben zOriginal (only cer-
tain AM Gtires)
Mercedes-Ben zOriginal Extende dtires may
only be used on wheelst hath ave been spe-
cificall yapprove dbyMercedes-Benz.
Only use tires, wheelsora ccessoriestested
and approve dbyMercedes-Benz. Certain
characteristics, e.g .handling, vehicle noise
emissionsorf uel consumption,m ay other-
wise be adverselyaffected. In addition,w hen
driv ingwithal oad, tir edimension variations
could caus ethe tires to come int ocontac t
340Wheel-tirec ombination
Wheels and tires