ignition MERCEDES-BENZ CLS 2014 Repair Manual

Page 191 of 382

again after thevehicle has been driven a
certain distance.
AIRMATIC
Vehicle level
Important safety notes
GWARNING
When thevehicle is beinglowered, people
could become trapped if their limbs are
between thevehicle body and thewheelsor
underneaththevehicle.There isarisk of
injury.
Make sure no one is underneath the vehicle
or in the immediate vicinity of the wheel
arches when the vehicle is being lowered.
GWARNING
Vehicles with level control:
The vehicle is slightly lowered if:
Ryou have selected comfort suspension
tuning and
Ryou lock the vehicle within approximately
60 seconds of switching off the engine
You and people in the vicinity of the wheel
arch or the underbody may thus become
trapped. There isarisk of injury.
Make sure that nobody is in the vicinity of the
wheel arch or the underbody when you lock
the vehicle.
!The vehicle is lowered by about 15 mm if:
Ryou have selected "Comfort tuning"
Ryou switch off the engine and then
Ryou lock the vehicle within approximately
60 seconds
When parking, position your vehicle so that
it does not make contact with the curb as
the vehicle is lowered. Your vehicle could
otherwise be damaged.
If you lock the vehicle within 60 seconds of
switching the engine off, it lowers slightly to
the selected Comfort suspension mode.
Your vehicle regulates its height
automatically.All-round level control ensures
the best possible suspension and constant
groundclearance, even withaladen vehicle.
When you drive fast,the vehicle is lowered
automatically to improve drivingsafetyand to
reducefuel consumption.
The followingvehicle levels are possible:
Rnormal
Rraised: the vehicle is raised by about
0.80 in (20 mm) when compared with the
normal level
Rlowered: the vehicle is raised by about
0.40 in (10 mm) when compared with the
normal level
iThese changes in level are so slight that
you are hardly aware of them.
The "Normal" and "Raised" vehicle levels can
be set manually.
The "Lowered” vehicle level is set
automatically:
Rat speeds above 70 mph (113km/h)
Rif you have selected "Sports tuning"
(Ypage 190)
Setting thevehicle level
Selectthe "Normal" settingfor normal road
surfaces and "Raised" for drivingwith snow
chainsoronparticularly poor road surfaces.
Your selection remainsstored even if you
remove the SmartKey fromthe ignition lock.
Setting raised level
XStart the engine.
Driving systems189
Driving and parking
Z

Page 192 of 382

If indicator lampis not lit:
XPress thebutton.
Indicator lamplights up. The vehicle
heightisadjusted to raised level.
TheVehicle Risingmessage appears in
the display.
The "Raised level" setting is canceled if you:
Rdrive ataspeed over approximately
75 mph (120 km/h)
Rdrive for approximately three minutes at a
speed over 50 mph (80 km/h)
The "Raised level" remains active when you
are not driving within these speed ranges.
Setting the normal level
XStart the engine.
If indicator lampis lit:
XPress thebutton.
Indicator lampgoes out. The vehicle is
adjusted to normal level.
Suspension tuning
General notes
The electronically controlled damping system
works continuously. This improves driving
safety and ride comfort.
The damping is tuned individually to each
wheel and depends on:
Ryour driving style, e.g. sporty
Rthe road surface condition, e.g. bumps
Ryour individualselection, i.e. sports or
comfort
Your selection remains stored even if you
remove the SmartKey from the ignition lock.
Sports tuning
The firmer suspension tuning in Sport mode
ensures even better contact with the road.
Select this mode when employingasporty
driving style, e.g. on winding country roads.
XPress button.
Indicator lamplights up. Sports
suspension tuning is selected.
TheAIRMATIC SPORTmessage appears in
the multifunction display.
Comfort tuning
In comfort mode, the driving characteristics
of your vehicle are more comfortable.
Therefore, select this mode if you favor a
more comfortable driving style. Select
comfort mode also when driving fast on
straight roads, e.g. on straight stretches of
freeway.
XPress button.
Indicator lamp$lights up. Comfort tuning
is selected.
TheAIRMATIC COMFORTmessage appears
in the multifunction display.
AMG adaptive sport suspension
system
Important safety notes
GWARNING
When the vehicle is being lowered, people
could become trapped if their limbs are
between the vehicle body and the wheels or
190Driving systems
Driving and parking

Page 195 of 382

Load compensation
The vehicle can compensatedifferences in
thevehicle level by raisingorlowering the
rear axle. This is the case, for example, if
people get out or if luggage is being loaded.
Load compensation takes place if:
Radoor or the trunk lid/tailgate is opened
Rthe parked vehicle is unlocked
For larger level changes, the engine must be
running.
4MATIC (permanent four-wheel drive)
If you fail to adapt your driving style, 4MATIC
can neither reduce the risk of accident nor
override the laws of physics. 4MATIC cannot
take account of road, weather and traffic
conditions. 4MATIC is only an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
Ifadrive wheel spins due to insufficientgrip:
ROnly depress the accelerator pedalasfar
as necessary when pulling away.
RAccelerate less when driving.
!Never tow the vehiclewith one axle
raised. This may damage the transfer case.
Damageofthis sort is not covered by the
Mercedes-Benz Limited Warranty. All
wheels must remaineitheronthe ground
or be fully raised. Observe the instructions
for towing the vehicle with all wheels in full
contact with the ground.
iIn wintry driving conditions, the maximum
effect of 4MATIC can only be achieved if
you use winter tires(M+S tires), with snow
chains if necessary.
4MATIC ensures that allfour wheels are
permanently driven. Together with ESP®,it
improves the traction of yourvehicle
wheneveradrive wheel spins due to
insufficient grip.
PARKTRONIC
Important safetynotes
PARKTRONIC is an electronic parkingaid with
ultrasonic sensors. It indicates visually and
audibly the distancebetween your vehicle
and an object.
PARKTRONIC is only an aid. It is not a
replacementfor your attention to your
immediate surroundings. You are always
responsible for safe maneuvering, parking
and exitingaparkingspace. When
maneuvering, parkingorpulling out of a
parkingspace, make sure that thereare no
persons, animals or objects in the area in
which you are maneuvering.
!When parking, pay particular attention to
objects above or below the sensors, such
as flower pots or trailer drawbars.
PARKTRONIC does not detectsuch objects
when they are in theimmediatevicinity of
thevehicle. You could damagethe vehicle
or the objects.
The sensors may not detect snow and other
objectsthat absorb ultrasonic waves.
Ultrasonic sources such as an automatic
car wash, the compressed-air brakes on a
truck orapneumatic drill could cause
PARKTRONIC to malfunction.
PARKTRONIC may not function correctly on
uneven terrain.
PARKTRONIC is activated automatically when
you:
Rswitch on the ignition
Rshift the transmission to positionD,RorN
Rrelease the parking brake
PARKTRONIC is deactivated at speeds above
11 mph (18 km/h). It is reactivated at lower
speeds.
PARKTRONIC monitors the area around your
vehicle using six sensors in the front bumper
and four sensors in the rear bumper.
Driving systems193
Driving and parking
Z

Page 197 of 382

Warning displays
Warning display for the front area
Segments on the left-hand side of the
vehicle
Segments on the right-hand side of the
vehicle
$Segments showing operational readiness
The warning displays show the distance
between the sensors and the obstacle. The
warning displayfor the front area is located
on the dashboard above the center airvents.
The warning display for the rear area is
located on the headliner in the rear
compartment.
The warning display for each side of the
vehicle is divided intofive yellow and two red
segments. PARKTRONIC is operational if
yellow segments showing operational
readiness$light up.
The selected transmission position and the
direction in which the vehicle is rolling
determine which warning display is active
when the engineisrunning.
Transmission
position
Warning display
DFrontarea activated
R,Nor the vehicle
is rolling
backwards
Rear and frontareas
activated
PNo areas activated
One or more segments light up as the vehicle
approaches an obstacle, depending on the
vehicle's distancefrom the obstacle.
From the:
Rsixthsegmentonwards,youwill hearan
intermittentwarningtonefor
approximately two seconds.
Rseventhsegment onwards, you will hear a
warning tonefor approximately two
seconds. This indicates that you have now
reached the minimum distance.
Deactivating/activating PARKTRONIC
Indicator lamp
To deactivate/activate PARKTRONIC
If indicator lamplights up, PARKTRONIC is
deactivated. Active Parking Assist is then also
deactivated.
iPARKTRONIC is automatically activated
when you turn the SmartKey to position2
in the ignition lock.
Driving systems195
Driving and parking
Z

Page 198 of 382

Problems with PARKTRONIC
ProblemPossible causes/consequences and Solutions
Only the red segments
in the PARKTRONIC
warning displaysare lit.
You also hearawarning
tone for approximately
two seconds.
PARKTRONIC is then
deactivated and the
indicator lamp on the
PARKTRONIC button
lights up.
PARKTRONIC has malfunctioned and has switched off.
XIf problems persist, have PARKTRONIC checked ataqualified
specialist workshop.
Only the red segments
in the PARKTRONIC
warning displaysare lit.
PARKTRONIC is then
deactivated.
The PARKTRONIC sensors are dirty or there is interference.
XCleanthe PARKTRONIC sensors (Ypage 315).
XSwitch the ignition back on.
The problem may be caused by an external source of radio or
ultrasound waves.
XSee if PARKTRONIC functions inadifferent location.
Active Parking Assist
General notes
Active Parking Assist is an electronic parking
aid with ultrasound. It measures the road on
both sides of the vehicle.Aparking symbol
indicatesasuitable parking space. Active
steering interventioncan assistyou during
parking. You may also use PARKTRONIC
(Ypage 193).
Important safety notes
Active Parking Assist is merely an aid. It is not
areplacement for your attention to your
immediate surroundings. You are always
responsible for safe maneuvering, parking
and exitingaparking space. Make sure that
no persons, animals or objectsare in the
maneuvering range.
When PARKTRONIC is switched off, Active
Parking Assist is also unavailable.
GWARNING
The vehicle swings out when parking and in
doing so could cross into the opposite lane.
This could result inacollision with another
road user. There isarisk of an accident.
Pay attention to other road users when
parking. Stop the vehicle if necessary or
cancel the Active Parking Assist parking
procedure.
!If unavoidable, you should drive over
obstacles such as curbs slowly and not at
asharp angle. Otherwise, you may damage
the wheels or tires.
Active Parking Assist may possibly indicate
parking spaces which are not suitable for
parking, for example:
Rwhere parking or stopping is prohibited
Rin front of driveways or entrances and exits
Ron unsuitable surfaces
196Driving systems
Driving and parking

Page 202 of 382

Rif the camera is exposed to very bright light
Rif the area is lit by fluorescentlight or LED
lighting (thedisplay may flicker)
Rif there isasudden change in temperature,
e.g. when drivingintoaheatedgarage in
winter
Rif the camera lens is dirtyorobstructed
Rif the rear of your vehicle is damaged. In
this event, have the camera position and
settingchecked ataqualified specialist
workshop.
General notes
Example: Coupe
Rear view camerais located in the handle
strip of the trunk lid.
Rear view camerais an optical parking and
maneuveringaid. It shows the area behind
your vehicle with guide lines in the COMAND
display.
The area behindthe vehicle is displayed as a
mirror image, as in the rear view mirror.
iThe textofmessages shown in the
COMAND display depends on the language
setting. The following are examples of rear
view camera messages in the COMAND
display.
Activating/deactivating the rear view
camera
XTo activate:make sure that the SmartKey
is in position2in the ignition lock.
XMake sure that the "Activation byRgear"
setting is active in COMAND,see the
separate COMAND operatinginstructions.
XEngage reversegear.
The area behind the vehicle is shown in the
COMAND display with guide lines.
To deactivate:the rear view camera is
deactivated if you:
Rshift the transmission to positionP
Rdrive 33 ft (10 m) forwards
Rshift the transmission fromRto another
position after 15 seconds
Rdrive forwards ataspeed of over5mph
(10 km/h)
Displays in the COMAND display
The rear view camera may showadistorted
view of obstacles, show them incorrectly or
not at all. The rear view camera does not show
objects in the following positions:
Rvery close to the rear bumper
Runder the rear bumper
Rin the area immediately above the tailgate
handle
!Objects not at ground level may appear to
be further away than they actually are, e.g.:
Rthe bumper ofaparked vehicle
Rthe drawbar ofatrailer
Rthe ball coupling ofatrailer tow hitch
Rthe rear section of an HGV
Raslanted post
Use the guidelines only for orientation.
Approachobjects no further than the
bottom-most guideline.
200Driving systems
Driving and parking

Page 207 of 382

highlighted in the Night View Assist Plus
display.
Light from the headlamps of oncoming
vehicles does not affect the Night View Assist
Plus displayinthe multifunction display. This
is also the case if you cannot switch on the
high-beam headlamps due to oncoming
traffic.
iInfrared light is not visible to the human
eye and therefore does not glare. Night
View Assist Plus can therefore remain
switched on even if there is oncoming
traffic.
Activating Night View Assist Plus
Activation conditions
You can only activate Night View Assist Plus
if:
Rthe SmartKey is in position2in the ignition
lock.
Rit is dark.
Rthe light switch is in the\ror
position.
Rreverse gear has not been engaged.
Activating Night View Assist Plus
XMake sure that COMAND is switched on.
XPress button.
The Night View Assist Plus displayappears
in the COMAND display.
You can read about how to adjust the
brightness of the COMAND displayinthe
COMAND operating instructions.
iThe infrared headlamps only switch on
when the vehicle is being driven at speeds
of approximately6mph (10 km/h). This
means that you do not have the full visual
range while the vehicle is stationary and
cannot check whether Night View Assist
Plus is working.
Pedestrian recognition
Night View Assist Plus display
Pedestrian recognized
$Framing
!Symbol for active pedestrian recognition
iAnimals are not recognized by pedestrian
recognition.
Night View Assist Plus is able to recognize
pedestrians by typical characteristics, e.g. a
silhouette in the shape ofaperson.
Pedestrian recognition is then switched on
automatically:
Rif Night View Assist Plus is activated
Rif you are driving faster than approximately
6mph (10 km/h)
Rthe surroundings are dark, e.g. when
driving outside built-up areas without
street lighting
If pedestrian recognition is active,
symbol!appears. If pedestriansare
detected, they are highlighted with framing
$.Ifthe pedestrian recognition system has
broughtapedestrian to your attention, look
through the windshield to evaluate the
situation. The actual distance to objectsand
Driving systems205
Driving and parking
Z

Page 211 of 382

indicator lamp goes out and BlindSpot Assist
is operational.
Ifavehicle is detected within the monitoring
rangeofBlindSpot Assist at speeds above
20 mph (30 km/h), warninglampon the
correspondingside lightsupred. This warning
is always emitted whenavehicle enters the
blind spot monitoring rangefrom behind or
from the side.When you overtakeavehicle,
the warning only occurs if the difference in
speed is less than7mph (12km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event,Blind Spot
Assist is no longer active.
The brightness of the indicator/warning
lamps is adjusted automatically according to
the ambient light.
Collision warning
Ifavehicle is detected in the monitoring range
of Blind Spot Assist and you switchonthe
correspondingturn signal,adouble warning
tonesounds. Red warning lampflashes. If
the turn signal remains on, vehicles detected
are indicated by the flashing of red warning
lamp.There are no further warning tones.
Switching on Blind Spot Assist
XMake sure that Blind Spot Assist
(Ypage 228) is activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Lane Keeping Assist
Important safety notes
GWARNING
Lane Keeping Assist may not always clearly
recognizelane markings.
In this case, Lane Keeping Assist may:
Rgive an unnecessary warning
Rnot giveawarning
There isarisk of an accident.
Always pay particular attention to the traffic
situation and stay in lane, in particular if
warned by Lane Keeping Assist.
GWARNING
The Lane Keeping Assist warning does not
return the vehicle to the original lane. There
isarisk of an accident.
You should always steer, brake or accelerate
yourself, in particular if warned by Lane
Keeping Assist.
If you fail to adapt your driving style, Lane
Keeping Assist can neither reduce the risk of
an accident nor override the laws of physics.
Lane Keeping Assist cannot take into account
the road, traffic and weather conditions. Lane
Keeping Assist is merely an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
The Lane Keeping Assist does not keep the
vehicle in the lane.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to
insufficient illumination of the road, or due
to snow, rain, fog or spray
Rthere is glare, e.g. from oncomingtraffic,
the sun or reflections (e.g. when the road
surface is wet)
Rthe windshield is dirty, fogged up, damaged
or covered, for instancebyasticker, in the
vicinity of the camera
Rthere are no, several or unclear lane
markings foralane, e.g. in areas with road
construction work
Rthe lane markings are worn away,dark or
covered up, e.g. by dirt or snow
Driving systems209
Driving and parking
Z

Page 215 of 382

The brightness of the indicator/warning
lamps is adjusted automatically accordingto
the ambient light.
Visual and acoustic collision warning
If you switch on the turn signals to change
lanes andavehicle is detected in the side
monitoring range, you receiveavisual and
acoustic collision warning. You then hear a
double warning toneand red warning
lampflashes. If the turn signal remains on,
detected vehicles are indicated by the
flashing of red warning lamp.There are no
further warning tones.
Course-correcting brake application
GWARNING
Acourse-correctingbrake application cannot
alwayspreventacollision. There isarisk of
an accident.
Always steer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
you or makesacourse-correcting brake
application. Always maintainasafe distance
at the sides.
If Active Blind Spot Assist detectsarisk of a
lateral collision in the monitoring range, a
course-correcting brake application is carried
out. This is meant to assist you in avoiding a
collision.
Ifacourse-correcting brake application
occurs, red warning lampflashes in the
exterior mirror andadual warning tone
sounds. In addition, the display shown in the
lower image appears in the multifunction
display.
In very rare cases, the system may make an
inappropriate brake application. An
inappropriate course-correcting brake
application may be interrupted at any time if
you steer slightly in the opposite direction or
accelerate, for example.
The course-correcting brake application is
available in the speed range between
20 mph (30 km/h) and 120 mph (200 km/h).
Either no braking application, oracourse-
correcting brake application adapted to the
driving situation occurs if:
Rthere are vehicles or obstacles, e.g. crash
barriers, located on both sides of your
vehicle.
Ravehicle approaches you too closely at the
side.
Ryou have adoptedasporty driving style with
high cornering speeds.
Ryou clearly brake or accelerate.
Radriving safety system intervenes, e.g.
ESP®or PRE-SAFE®Brake.
RESP®is switched off.
Raloss of tire pressure oradefectivetire is
detected.
Switching on Active Blind Spot Assist
XMake sure that the radar sensor system
(Ypage 232) and Active Blind Spot Assist
(Ypage 228) are activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Driving systems213
Driving and parking
Z

Page 222 of 382

Outsidetemperature display
You should pay special attention to road
conditions when temperatures are around
freezing point.
The outside temperature display is in the
multifunction display (Ypage 221).
Changes in the outside temperature are
displayed afterashort delay.
Speedometer with segments
The segments in the speedometer indicate
which speed range is available.
RCruise control activated (Ypage 175):
The segments light up from the stored
speed to the maximum speed.
RDISTRONIC PLUS activated (Ypage 177):
One or two segments in the set speed
range light up.
RDISTRONIC PLUS detectsavehicle in front:
The segments between the speed of the
vehicle in frontand the stored speed light
up.
Operatingthe on-board computer
Overview
Multifunctiondisplay
Right control panel
$Switches on the VoiceControl System;
see the separateoperating instructions
!Backbutton
Left control panel
XTo activatethe on-board computer:turn
the SmartKey to position1in the ignition
lock.
You can control the multifunction displayand
the settings in the on-board computer using
the buttons on the multifunction steering
wheel.
220Displays and operation
On-board computer and displays

Page:   < prev 1-10 ... 21-30 31-40 41-50 51-60 61-70 71-80 81-90 91-100 101-110 ... 110 next >