MERCEDES-BENZ E-CLASS ESTATE 2021 Owners Manual

ing se
vere thunderstorms, forex ample, and
may cause the fuse in the building totrip or
may inter rupt thech arging process. These
functions pr otect theve hicle.
ATer the fuse in the building is switched on
again, thech arging process resumes automat-
icall y.
Fo llowing an inter ruption in the po wer supply
without the fuse in the building being tripped,
it may take up to te n minutes forch arging to
re sume automaticall y.*
N
NO
OTE
TE Damage due toove rheating of
ch arging cable and charging cable con-
nector During
thech arging process, thech arging
cable and charging cable connector can heat
up within their permissible limit values.
The permissible limit values are in0uenced by
th efo llowing factors:
R the po wer supply system and thech arging
cable are not damaged R
the inst ructions for handling thech arging
cable and the control element on the
ch arging cable ha vebeen obser ved #
Ifth ech arging cable or charging cable
connector becomes too hot, ha vethe
po we r supply system checked. *
N
NOOTE
TE Damaged or dirty vehicle soc ket
when the soc ket 0ap is open #
Alwayske ep the soc ket co ver and the
soc ket 0ap closed when there is no
ch arging cable connected. This pr otects
th eve hicle soc ket from dirt and damage. #
Make sure that the soc ket co ver is
closed proper lybefore closing the soc ket
0ap. This can otherwise result in damage
which may pr event the soc ket 0ap from
being opened again. R
R
eq
eq uir
uir ements:
ements:
R The transmission is in position j.
R The hybrid system is not activated. The õ
display in the Instrument Display is o.. R
The vehicle is unloc ked.
R The charging cable is not taut.
T
T ype 1 v
ype 1 v ehicle soc ket
ehicle soc ket #
Press the bottom leT of soc ket 0ap 1and
swing the soc ket 0ap open outwards. 218
218
Driving and parking

%
When thehy brid system is activated (the
õ display in the Instrument Display),
soc ket 0ap 1cannot be opened. #
Press catch 3tothe leT and fold up soc ket
co ver5. #
T
To c
o c harg
harg e at a mains soc ke
e at a mains soc ket (mode 2):
t (mode 2): insert
th e mains plug into the mains soc ket of the
ex tern al po wer source tothe stop. #
Set the maximum charging cur rent if requ ired. #
Insert thech arging cable connector into vehi-
cle soc ket2 tothe stop.
Make sure that thech arging cable is not taut
when inser ted.
Indicator lamp 40ashes orange and, as soon
as the high-voltage battery is charge d, green. #
T
To c
o c harg
harg e at a w
e at a w allbo
allbo x/c
x/char
harging st
ging st ation
ation
(mode 3):
(mode 3): insertthech arging cable connector
into vehicle soc ket2 tothe stop.
Make sure that thech arging cable is not taut
when inser ted.
Indicator lamp 40ashes orange and, as soon
as the high-voltage battery is charge d, green. When
thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arging
side is shown in the Instrument Display with a
ch arging prediction. The charging prediction
either refers to the predicted charge leve l at the
set departure time, or the time at which the high-
vo ltage battery will be fully charge d.
T
T ype 2 v
ype 2 v ehicle soc ket
ehicle soc ket #
Press the bottom leT of soc ket 0ap 1and
swing the soc ket 0ap open outwards.
The % indicator lamp 4lights up.
% When thehy brid system is activated (the
õ display in the Instrument Display),
soc ket 0ap 1cannot be opened. #
Press catch 3tothe leT and fold up soc ket
co ver6. #
T
To c
o c harg
harg e at a mains soc ke
e at a mains soc ket (mode 2):
t (mode 2): insert
th e mains plug into the mains soc ket of the
ex tern al po wer source tothe stop. #
Set the maximum charging cur rent if requ ired. #
Insert thech arging cable connector into vehi-
cle soc ket2 tothe stop.
Make sure that thech arging cable is not taut
when inser ted.
The # indicator lamp 50ashes orange
and, as soon as the high-voltage battery is
ch arge d, green. #
Char
Char ging at a w
ging at a w allbo
allbo x/c
x/char
harging st
ging st ation (mode
ation (mode
3) wit
3) wit hout pr
hout pr e-inst
e-installed cable:
alled cable: insertthe Driving and parking
219
219

ch
arging cable connector into vehicle soc ket
2 tothe stop. #
Insert thech arging cable connector into the
soc ket of thewa llbox tothe stop.
Make sure that thech arging cable is not taut
when inser ted.
The # indicator lamp 50ashes orange
and, as soon as the high-voltage battery is
ch arge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arging
side is shown in the Instrument Display with a
ch arging prediction. The charging prediction
either refers to the predicted charge leve l at the
set departure time, or the time at which the high-
vo ltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as needed or when electrical consumers are
activated. Ending t Ending t
he c
he char
harging pr
ging pr ocess
ocess T
T
ype 1 v
ype 1 v ehicle soc ket
ehicle soc ket #
Press and hold button 1onthech arging
cable connector and remo vethech arging
cable connector from theve hicle soc ket.
% Ifth ech arging cable connector is bloc ked,
contact a quali/ed specialist workshop. #
Char
Char ging at a mains soc ke
ging at a mains soc ket (mode 2):
t (mode 2): discon-
nect the mains plug from the mains soc ket
and st owthech arging cable safely in theve hi-
cle (/ page 210). #
Close the soc ket co ver and the soc ket 0ap. 220
220
Driving and parking

T
T
ype 2 v
ype 2 v ehicle soc ket
ehicle soc ket #
Unlo cktheve hicle.
The charging process is ended. The %indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. #
Remo vethech arging cable connector from
th eve hicle soc ket within 30 seconds.
ATer the 30 seconds ha veelapsed, theve hicle
soc ket will be loc ked again and thech arging
process will resume.
% Ifyo u cannot remo vethech arging cable con-
nector, repeat the unlocking procedure. If the
ch arging cable connector is still loc ked, con-
ta ct a quali/ed specialist workshop. #
Char
Char ging at a mains soc ke
ging at a mains soc ket (mode 2):
t (mode 2): discon-
nect the mains plug from the mains soc ket
and st owthech arging cable safely in theve hi-
cle (/ page 210). #
Char
Char ging at a w
ging at a w allbo
allbox/c
x/char
harging st
ging st ation (mode
ation (mode
3) wit
3) wit hout pr
hout pr e-inst
e-installed c
alled c har
harging cable:
ging cable:
re mo vethech arging cable connector from the
wa llbox soc ket and st owthech arging cable
safely in theve hicle (/ page 210). #
Close the soc ket co ver and the soc ket 0ap.
% ATer thech arging cable connector has been
disconnected, the leT % indicator lamp 1
on theve hicle soc ketre mains lit for some
time before switching o.. F
F
unction of t
unction of t he c
he charg
harg e lev
e lev el displa
el displa y in t
y in t he Ins
he Instr tru-
u-
ment Display
ment Display 1
Current charge level
2 Time at which comple tely ch arged
3 Predicted charge leve l at pre-selected depar-
ture time
4 Current charging capacity
When theve hicle is connected tothe mains sup-
ply and is switched o., the Instrument Display
sho ws th ech arge leve l display for appr oximately
two minutes.
The value for cur rent charging capacity 4may
di.er from the display on thech arging station. At Driving and parking
221 221

a
ch arging capacity of 10 kW or highe r,th eva lue
in thech arge leve l display is rounded o. and
shown without a decimal place.
% The value in item 3varies depending on the
setting of thech arging process. It displ aysthe
ch arging prediction, e.g. the time at which the
selected charge leve l will be reached or the
ch arge leve l at the pre-selected departure
time. P
P
ar
ar king
king P
P
ar
ar king t
king t he v
he vehicle
ehicle &
W
WARNING
ARNING Risk of accident and injury
caused byan insu1ciently secured vehi-
cle rolling away
If th eve hicle is not securely par ked su1-
cient ly,it can rollawa y in an uncontrolled way
eve n at a slight downhill gradient. #
On uphill or downhill gradients, turn the
front wheels so that theve hicle rolls
to wa rdsth eke rb if it starts moving. #
apply the parking brake. #
Switch the transmission toposition j. &
W
WARNING
ARNING Risk of /re caused byhot
ex haust system parts
Flammable materials such as lea ves, grass or
twigs may ignite. #
Park theve hicle so that no 0ammable
material can come into contact with hot
ve hicle components. #
In particular, do not park on dry grass-
land or har vested grain /elds. &
W
WARNING
ARNING Risk of accident and injury due
to leaving children unattended in theve hi-
cle
If ch ildren are leT unattended in theve hicle,
th ey could, in particular:
R open doors, thereby endangering other
persons or road users.
R get out and be struck byoncoming tra1c. R
operate vehicle equipment and become
trapped, forex ample.
In addition, thech ildren could also set the
ve hicle in motion by,fo rex ample:
R releasing the parking brake.
R changing the transmission position.
R starting theve hicle. #
Never lea vechildren unattended in the
ve hicle. #
When leaving theve hicle, alw aysta ke the
ke y with you and lock theve hicle. #
Keep theve hicle key out of there ach of
ch ildren. *
N
NOOTE
TE Damage totheve hicle due toitro ll-
ing away #
Always secure theve hicle against rolling
awa y. 222
222
Driving and parking

*
N
N O
OTE
TE Damage due totheve hicle lo wering V
V
ehicles wit
ehicles wit h AIR BOD
h AIR BODY C
Y CONTR
ONTR OL or lev
OL or lev el
el
contr
contr ol:
ol:The vehicle can lo wer because of tem-
perature di.erences or longer non-operational
times. This can cause damage toparts of the
body. #
When stopping theve hicle and when
driving o., make sure that there are no
obstacles such as curbs under or in the
immediate vicinity of the body. #
Bring theve hicle toa standstill bypressing the
brake pedal. #
Ongradients, turn the front wheels so that the
ve hicle will rollto wa rdsth eke rb if it starts
moving. #
Apply the electric parking brake. #
Engage transmission position jin a station-
ary vehicle with the brake pedal applied
(/ page 201). #
Switch o. theve hicle bypressing the1 but-
to n. #
Release the service brake slo wly. #
Get out of theve hicle and lock it.
% When you park theve hicle, you can still oper-
ate the side windo wsand the sliding sunroof
fo r appr oximately four minutes if the driver's
door is closed.
% When you park theve hicle, you can still oper-
ate the side windo wsand the panoramic slid-
ing sunroof for appr oximately four minutes if
th e driver's door is closed. Driving and parking
223 223

Gar
Gar
ag
age door opener
e door opener Pr
Pr
ogr
ogr amming butt
amming butt ons f
ons for t
or the g
he g ar
arag
ag e door opener
e door opener &
D
DAN
AN GER
GER Risk of fatal injuries caused by
ex haust gases
Combustion engines emit poisonous exhaust
ga ses such as carbon monoxide. Inhaling
th ese exhaust gases is hazardous tohealth
and leads topoisoning. #
Never lea vetheve hicle or, if present, the
stationa ryheater running in an enclosed
space without su1cient ventilation. &
W
WARNI NG
ARNI NGRisk of injury bybecoming
trapped when opening and closing a
ga rage door
When you operate or prog ram a garage door
with an integ ratedga rage door opener, per-
sons can become trapped or struck bythe
ga rage door if they stand wi thin its range of
mo vement. #
Always make sure that nobody is within
th era nge of thega rage door's mo ve-
ment. R
R
eq
eq uir
uir ements:
ements:
R The vehicle has been par ked outside the
gar age or outside thera nge of mo vement of
th e door.
R The vehicle is switched on.
R The vehicle has not been star ted.
% The garage door opener function is alw ays
av ailable when theve hicle is switched on. #
Press and hold but ton1, 2or3 that you
wish toprog ram.
Indicator lamp 40ashes yello w.
% It can take up to20 seconds before the indi-
cator lamp 0ashes yello w. #
Release the pr eviously pressed button.
Indicator lamp 4continues to0ash yello w. 224
224
Driving and parking

#
Point remo tecont rol6 from a distance of
1 cm to8 cm towa rds button 1,2or3. #
Press and hold button 5ofremo tecont rol
6 until one of thefo llowing signals appears:
R Indicator lamp 4lights up green continu-
ousl y.Prog ramming is comple te.
R Indicator lamp 40ashes green. Prog ram-
ming was successful. Additionall y,syn-
ch ronisation of thero lling code with the
door system must be car ried out. #
If indicator lamp 4does not light up or 0ash
gr een: repeat the procedure. #
Release all of the buttons.
% The remo tecont rolfo rth e door drive is not
included in the scope of delivery of thega rage
door opener.
Sync
Sync hr
hronising t
onising t he r
he rolling code
olling code
R
R eq
eq uir
uir ements:
ements:
R The door system uses a rolling code.
R The vehicle must be within range of thega rage
door or door drive. R
The vehicle as well as persons and objects are
located outside thera nge of mo vement of the
door. #
Press the prog ramming button on the door
drive unit.
Initiate the next step within appr oximately
30 seconds. #
Press pr eviously prog rammed button 1,2
or 3 repeatedly until the door closes.
When the door closes, prog ramming is com-
ple ted.
% Please also read the operating inst ructions for
th e door drive.
T T r
roubleshoo
oubleshoo ting when pr
ting when progr ogramming t
amming t he r
he remo te
emo te
contr
contr ol
ol #
Check if the transmitter frequency of remo te
cont rol6 is suppor ted. #
Replace the batteries in remo tecont rol6. #
Hold remo tecont rol6 atvarious angles from
a distance of 1 cm to8 cm front of the inside
re arview mir ror.Yo u should test every position
fo r at least 25 seconds before trying ano ther
position. #
Hold remo tecont rol6 atthe same angles at
va rious distances in front of the inside rear
view mir ror.Yo u should test every position for
at least 25 seconds before trying ano ther
position. #
Onremo tecont rolsth at transmit only for a
limited period, press button 5onremo te
cont rol6 again before transmission ends. #
Angle the aerial line of thega rage door opener
unit towa rdsth ere mo tecont rol.
% Support and additional information on pro-
gramming:
R Onthe HomeLink ®
Hotline on (0) 08000
466 354 65 or +49 (0) 6838 907-277
R Onthe Internet at https://
www.homelink.com
Opening or closing t
Opening or closing t he g he gar
arag
ag e door
e door
R
R eq
eq uir
uir ements:
ements:
R The cor responding button is prog rammed to
operate the door. #
Press and hold buttons 1,2or3 until the
door opens or closes. Driving and parking
225
225

#
If indicator lamp 40ashes yellow aTer
appr oximately 20 seconds: press and hold the
pr ev iously pressed button again until the door
opens or closes.
Clear
Clear ing t
ing the g
he gar
arag
ag e door opener memory
e door opener memory #
Press and hold buttons 1and 3.
Indicator lamp 4lights up yello w. #
If indicator lamp 40ashes green: release
buttons 1and 3.
The entire memory has been dele ted. Electr
Electr
ic par
ic parking br
king br ake
ake F
F
unction of t
unction of t he electr
he electric par
ic parking br
king br ak
ake (appl
e (appl ying
ying
aut
aut omaticall
omaticall y)
y) &
W
WARNING
ARNING Risk of accident and inju rydue
to leaving children unattended in theve hi-
cle
If ch ildren are leT unattended in theve hicle,
th ey could, in particular:
R open doors, thereby endangering other
persons or road users.
R get out and be struck byoncoming tra1c.
R operate vehicle equipment and become
trapped, forex ample.
In addition, thech ildren could also set the
ve hicle in motion by,fo rex ample:
R releasing the parking brake.
R changing the transmission position.
R starting theve hicle. #
Never lea vechildren unattended in the
ve hicle. #
When leaving theve hicle, alw aysta ke the
ke y with you and lock theve hicle. #
Keep theve hicle key out of there ach of
ch ildren. The electr
The electr
ic par
ic parking br
king br ak
ake is applied if t
e is applied if t he tr
he trans-
ans-
mission is in position
mission is in position j
jand one of t
and one of t he f
he follo
ollowing
wing
conditions is
conditions is ful/lled:
ful/lled:
R The vehicle is switched o..
R The seat belt tongue is not inse rted in the seat
belt buckle of the driver's seat and the driver's
door is opened.
% Toprev ent application: pull the handle of the
electric parking brake (/ page 227).
In t
In t he f
he f ollo
ollowing situations, t
wing situations, t he electr
he electric par
ic parking
king
br
br ak
ak e is also applied:
e is also applied:
R The HOLD function is keeping theve hicle sta-
tionar y.
R Active Parking Assist is keeping theve hicle
stationar y.
R Active Distance Assist DISTRONIC is bringing
th eve hicle toa standstill. 226
226
Driving and parking

R
In addition, one of t
In addition, one of t he f
he follo
ollowing conditions
wing conditions
mus
mus t be
t be ful/lled:
ful/lled:
- The vehicle is switched o..
- The seat belt tongue is not inse rted in the
seat belt buckle of the driver's seat and
th e driver's door is opened.
- There is a system malfunction.
- The po wer supply is insu1cient.
- The vehicle is stationary for a lengt hy
period.
When the electric parking brake is applied, the
re d! indicator lamp lights up in the inst ru-
ment clus ter.
% The electric parking brake is not automatically
applied if theve hicle is switched o. bythe
ECO start/s top function.
F
F unction of t unction of t he electr
he electric par
ic par king br
king br ak
ake (r
e (r eleasing
eleasing
aut
aut omaticall
omaticall y)
y)
The electr
The electr ic par
ic parking br
king br ak
ake is r
e is r eleased when t
eleased when t he
he
f
f ollo
ollo wing conditions ar
wing conditions ar e
eful/lled:
ful/lled:
R The driver's door is closed.
R The vehicle has been star ted. R
The transmission is in position hork and
yo u depress the accelerator pedal or you shiT
from transmission position jtoh ork
when on le velgr ound.
R Ifth e transmission is in position k,theta il-
ga te must be closed.
R The seat belt tongue is inse rted into the seat
belt buckle of the driver's seat.
If th e seat belt tongue is not inse rted into the
seat belt buckle of the driver's seat, one of the
fo llowing conditions must be ful/lled:
- You shiT from transmission position j.
or
- You ha veprev iously driven at speeds
gre ater than 3 km/h.
When the electric parking brake is released, the
re d! indicator lamp in the inst rument cluster
goes out. Appl
Appl ying/r
ying/r eleasing t
eleasing t he electr
he electric par
ic parking br
king br ake
ake
manually
manually
Appl Appl ying
ying #
Push handle 1.
The red! indicator lamp lights up in the
inst rument cluster. Driving and parking
227
227