display MERCEDES-BENZ S CLASS 2016 Manual Online

Activating when driving with the electric motor: X
Pull the left or right steering wheel paddle
shifter ( Y
page 174).
The combustion engine is switched on. Man-
ual drive program M is temporarily activated.
The selected gear and M appear in the multi-
function display.
Activating when driving with the combustion
engine: X
Pull the left or right steering wheel paddle
shifter ( Y
page 174).
Manual drive program M is temporarily acti-
vated. The selected gear and M appear in the
multifunction display.
The ECO start/stop function is not available in
manual drive program M .
Haptic accelerator pedal General notes The haptic accelerator pedal helps you to
reduce the fuel consumption and emissions of
your vehicle.
There are two different functions available for
this purpose: R
an additional point of resistance in E-MODE
operating mode ( Y
page 243)R
a double impulse in E+ operating mode
( Y
page 250)
Additional point of resistance in the hap-
tic accelerator pedal The maximum available electric performance is
indicated by a tangible point of resistance in the
haptic accelerator pedal.
The additional point of resistance is available in
E-MODE operating mode ( Y
page 243).
If you depress the haptic accelerator pedal
beyond the pressure point, the combustion
engine is switched on.
Double pulses in the haptic accelerator
pedal
A tangible double pulse in the haptic accelerator
pedal gives you a recommendation to release
the accelerator pedal. The combustion engine
can switch off and be disconnected from the
drive train (overrun mode).
The double pulse is available in drive program E+
( Y
page 250). After the accelerator pedal has been released,
the coasting characteristics of the vehicle are
adapted to the traffic conditions.
To avo id getting too close to the vehicle in front,
y
ou must apply the brakes manually when nec-
essary.
Driving tips General driving tips Drive carefully and maintain a safe distance
from the vehicle in front. Avoid frequent and
sudden acceleration as well as abrupt braking.
During partial electric driving, pulling away and
acceleration, the electric motor supports the
internal combustion engine.
During overrun in transmission position D and
braking, the electric motor will operate as a gen-
erator.
Further information on the ECO start/stop func-
tion ( Y
page 252).
Additional driving tips ( Y
page 192).
Stationary vehicle If the vehicle is stopped, the combustion engine
is, for the most part, switched off. Automatic
climate control continues to function. The elec-
tromechanically assisted steering gear allows
you to use the power steering without reduced
comfort.
Acceleration Depending on the operating mode, pulling away
and driving under low load conditions are per-
formed: R
entirely by electric propulsion R
in combination with the internal combustion
engine
When accelerating at an increased or full load,
boost mode is utilized. The electric motor sup-
ports the internal combustion engine by provid-
ing additional torque when the accelerator is
depressed rapidly.
Overrun mode or braking
There are three possible operating modes when
the hybrid vehicle is decelerating: R
energy recovery takes place even when the
vehicle is decelerating purely in overrun mode
( Y
page 240). The electric motor operates asPLUG ‑ IN HYBRID operation 251
Driving an d parking Z

Aut oma tic engine startThe automatically switched-off internal combus -
tio n engin e start s automatically in certai n situa-
tions , if:R
th e power demand from th e driver via th e
accelerato r pedal is greate r than th e electric
motor alon e can provideR
th e driver switches to driv e program S or MR
th e condition of charge of th e high-voltage
battery has reached th e lower limitR
th e settings of th e automatic climat e control
require it, e.g. at external temperatures abov e
30 †
Over ru n mod eIn overrun mode, th e combustio n engin e is
switched off and is disconnected from th e driv e
train. The electric motor: R
generates low thrust , whic h correspond s to
th e overrun mod e of an active combustio n
engin eR
function s as a generator and produce s th e
necessary energ y for th e auxiliary consumer s
and charge s th e high-voltage battery
Ove rrun mod e is possible in th e followin g spee d
range: R
in driv e program E below 81 mph (13 0 km/h)R
in driv e program E+ below 11 2 mph
(18 0 km/h)
In driv e program E+ , after th e accelerato r pedal
has been released th e coasting characteristic s
of th e vehicl e are adapted to th e traffic condi-
tions . Further information about th e haptic
accelerato r p edal ( Y
page 251).
Route-based operating strategy Fo r th e route-based operating strategy, th e sys-
te m factors in information about th e expecte d
rout e when rout e guidance is active.
The information on th e rout e is provide d by th e
multimedia system and includes th e following:R
road categories R
spee d limitation sR
dat a on downhill gradients The use of electric energ y is automatically opti-
mally distributed from th e beginnin g to th e en d
of th e journey, usin g information about th e
route. The distribution is pre-emptive and takes
int o consideration : R
th e sections of th e journey aheadR
th e energ y consumption on th e whole rout e
The condition of charge of th e high-voltage bat -
tery is thus systematically controlled. In addi-
tion, th e control function takes int o accoun t
that: R
th e fuel saving s throug h th e use of electrical
energ y can vary, depending on th e rout e (e.g.
urban , interurban or highway) R
th e use of electrical energ y is held available in
particular for electric operation (e.g. urban
routes)
The vehicl e thus automatically select s th e opti-
mum driving mod e for th e respectiv e sectio n of
th e route.
The route-based operating strategy is available
under th e followin g conditions: R
driv e program E+ is selected R
HYBRID driving mod e is selectedR
active rout e g uidance is activated R
suitable map dat a is available
When th e route-based operating strategy is
bein g used, th e area in fron t of th e vehicl e is
shown as green in th e multifunction display.
Parking X
Apply th e electric parking brake.
The red $ indicator lamp in th e instrumen t
cluste r light s up. X
Use th e DIRECT SELECT leve r to shif t th e
automatic transmission to P .X
Switch th e ignition off .
The READY indicator in th e instrumen t cluste r
goes out .
Further information on parking and switching off
th e internal combustio n engin e ( Y
page 190).PLUG ‑ IN HYBRID operation 253
Driving and parking Z

Problems with PLUG-IN HYBRID operation
Internal combustion engine Problem
Possible causes/consequences and P Solutions
You cannot start the
internal combustion
engine. The multifunc-
tion display shows no
display messages. The
READY indicator in the
multifunction display is
off. For example, self-diagnosis is not yet complete or the hybrid drive
system is malfunctioning. X
Switch off the ignition and turn it back on. X
Try to start the internal combustion engine again.
If the internal combustion engine still does not start: X
Consult a qualified specialist workshop.
You wish to pull away,
but the ECO start/stop
function does not start
the internal combustion
engine. The READY indi-
cator in the multifunc-
tion display is off. The ECO start/stop function has failed. The warning and indicator
lamps in the instrument cluster light up. X
Shift the transmission to P .X
Switch off the ignition and turn it back on. X
Start the engine.
The hybrid drive system is faulty. X
Consult a qualified specialist workshop.
Recuperative Brake System Problem
Possible causes/consequences and P Solutions
Braking resistance is
reduced and brake pedal
travel is longer than
usual.
G Risk of accident
The Recuperative Brake System is malfunctioning. X
Observe the additional display messages in the multifunction dis-
play ( Y
page 277). X
Observe the information regarding indicator and warning lamps in
the instrument cluster ( Y
page 315) .254
PLUG ‑ IN HYBRID operation
Driving and parking

Hybrid drive system Problem
Possible causes/consequences and P Solutions
The hybrid drive system
has been switched off
automatically. You have been in an accident.
The hybrid drive system remains switched off if: R
the internal combustion engine cannot be restarted after a few
seconds. R
the red u restraint system warning lamp in the instrument clus-
ter is lit. X
Consult a qualified specialist workshop.
The hybrid drive system
has been switched off
automatically. The multi-
function display also
shows a display mes-
sage. An electrical short circuit has occurred in the hybrid drive system or an
electrical connection has been disconnected. X
Observe the additional display messages in the multifunction dis-
play ( Y
page 277). X
Consult a qualified specialist workshop. PLUG ‑ IN HYBRID operation 255
Driving and parking Z

Useful information
i This Operator's Manual describes all models
and all standard and optional equipment of
your vehicle available at the time of publica-
tion of the Operator's Manual. Country-spe-
cific differences are possible. Please note
that your vehicle may not be equipped with all
features described. This also applies to
safety-related systems and functions.
i Read the information on qualified specialist
workshops ( Y
page 28).
Important safety notes
G WARNING
If you operate information systems and com-
munication equipment integrated in the vehi-
cle while driving, you will be distracted from
traffic conditions. You could also lose control
of the vehicle. There is a risk of an accident.
Only operate the equipment when the traffic
situation permits. If you are not sure that this
is possible, park the vehicle paying attention
to traffic conditions and operate the equip-
ment when the vehicle is stationary.
You must observe the legal requirements for the
country in which you are currently driving when
operating the on-board computer.
PLUG-IN HYBRID vehicles only:
G WARNING
If the instrument cluster has failed or mal-
functioned, you may not recognize function
restrictions in systems relevant to safety. The
operating safety of your vehicle may be
impaired. There is a risk of an accident.
Pull over as soon as it is safe to do so and
consult a qualified specialist workshop.
All vehicles, except PLUG-IN HYBRID vehi-
cles:
G WARNING
If the instrument cluster has failed or mal-
functioned, you may not recognize function
restrictions in systems relevant to safety. The operating safety of your vehicle may be
impaired. There is a risk of an accident.
Drive on carefully. Have the vehicle checked
at a qualified specialist workshop immedi-
ately.
If the operating safety of your vehicle is
impaired, pull over as soon as it is safe to do so.
Contact a qualified specialist workshop.
The on-board computer only shows messages or
warnings from certain systems in the multifunc-
tion display. You should therefore make sure
your vehicle is operating safely at all times.
For an overview, see the instrument panel illus-
tration ( Y
page 33).
Displays and operation
Instrument cluster lighting The light sensor in the instrument cluster auto-
matically controls the brightness of the multi-
function display. In daylight, the displays in the
instrument cluster are illuminated. A dimming
function is not possible in daylight.
The lighting in the instrument cluster, in the dis-
plays and the controls in the vehicle interior can
be adjusted using the brightness control knob.
The brightness control is located between the
instrument cluster and the multimedia system
display ( Y
page 35). X
Turn the brightness control knob clockwise or
counter-clockwise.
If you turn the light switch ( Y
page 130) to the
` , X or X position, the brightness
will depend upon the brightness of the ambi-
ent light.
Tachometer
! Do not drive in the overrevving range, as this
could damage the engine.
The red band in the tachometer indicates the
engine's overrevving range.
The fuel supply is interrupted to protect the
engine when the red band is reached.
PLUG-IN HYBRID vehicles: if you select the oper-
ating mode E-MODE , the display in the instru-
ment cluster changes from tachometer to power
meter ( Y
page 242).256
Displays and operation
On-board computer and displays

Outside temperature display You should pay special attention to road condi-
tions when temperatures are around freezing
point.
Bear in mind that the outside temperature dis-
play indicates the temperature measured and
does not record the road temperature.
The outside temperature display is in the multi-
function display ( Y
page 258).
There is a short delay before a change in outside
temperature is shown in the multifunction dis-
play.
Coolant temperature display
G WARNING
Opening the hood when the engine is over-
heated or when there is a fire in the engine
compartment could expose you to hot gases
or other service products. There is a risk of
injury.
Let an overheated engine cool down before
opening the hood. If there is a fire in the
engine compartment, keep the hood closed
and contact the fire department.
! A display message is shown if the coolant
temperature is too high.
If the coolant temperature is above 257 ‡
(125 †) do not drive any further. The engine
will otherwise be damaged.
All vehicles except PLUG ‑ IN HYBRID vehicles:
the coolant temperature gauge is in the lower
area of the tachometer ( Y
page 33).
PLUG-IN HYBRID vehicles: the multifunction dis-
play shows the coolant temperature in the
Coolant submenu ( Y
page 269).
Under normal operating conditions and with the
specified coolant level, the coolant temperature
may rise to 255 ‡ (124 †). Operating the on-board computer
C
Multifunction display D
Right control panel

Head-up display
General notes The head-up display projects information from
the navigation system and the driver assistance
system above the dashboard into the driver's
field of vision. The head-up display allows the
driver to see all of the information without hav-
ing to take their eyes off the road.
A requirement for the display of the contents is
that the following functions are available in the
vehicle and are switched on: R
Cruise control R
DISTRONIC PLUS R
Traffic Sign Assist R
Navigation
Important safety notes The head-up display is only an aid and is not a
substitute for attentive driving.
Speed limits and overtaking restrictions are not
always correctly displayed. Traffic signs always
have priority over the Traffic Sign Assist display.
The visibility of the head-up display is influenced
by the following conditions: R
the driver's seat position R
the positioning of the display image R
the general ambient light R
sunglasses with polarization filters R
wet roads R
blocking of sunlight by objects on the display
cover
In the event of extreme sunlight, sections of the
display may fade. This can be reversed by
switching the head-up display off and on again.
i Vehicles with the head-up display are equip-
ped with a special windshield. Should repairs
be necessary, have the windshield replaced at
a qualified specialist workshop. Displays and operation Switching the head-up display on/off X
Press button C .
When the head-up display is switched on, the
display appears in the driver's field of vision.Displays and operation 259
On-board computer and displays Z

Standard displays in the head-up display The head-up display shows the following contents and information.
C
Navigation messagesD
Current speed

Setting options You can adjust the following settings in the
head-up display submenu: R
adjust the position of the head-up display on
the windshield ( Y
page 273)R
adjust the brightness of the displays in the
head-up display ( Y
page 273)R
select displays in the head-up display
( Y
page 273).
Using the Display Content
function, you
can, depending on your vehicle's equipment,
choose between four standard displays. The
selected contents then appear in the head-up
display.
In Mercedes-AMG vehicles, you can also
choose between two AMG displays. If you
select an AMG display, the head-up display
shows AMG-specific contents.
If you select a display with traffic signs, detec-
ted traffic signs from Traffic Sign Assist
appear in the head-up display.
Menus and submenus
Menu overview Press the

R
Distance warning and the autonomous
braking function COLLISION PREVENTION
ASSIST PLUS ( Y
page 71)R
PRE-SAFE ®
Brake ( Y
page 75)R
Active Blind Spot Assist ( Y
page 234)R
ATTENTION ASSIST ( Y
page 228)R
Active Lane Keeping Assist ( Y
page 237)X
Press d to display the ATTENTION ASSIST
assessment.
Service menu
Introduction
Depending on the equipment installed in the
vehicle, you have the following options in the
Service menu:R
Calling up display messages in message
memory ( Y
page 277)R
Restarting the tire pressure loss warning sys-
tem ( Y
page 394)R
Checking the tire pressure electronically
( Y
page 390) R
Calling up the service due date ( Y
page 358).R
Displaying the coolant temperature (PLUG-IN
HYBRID vehicles) ( Y
page 269)R
Checking the oil level using the on-board com-
puter ( Y
page 355) (only S 600, Mercedes-
Maybach S 600 and Mercedes-AMG S 65
models)
Displaying the coolant temperature
The Coolant menu is only available on PLUG ‑ IN
HYBRID vehicles. X
Press the