MITSUBISHI ASX 2015 Owner's Manual (in English)

Page 391 of 452

3.While holding down the tab (D), pull out
the socket (E).
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying it thoroughly.Daytime running lamps (type
2)*/Position lamps (type 2)*
E01012000021
NOTEl An LED, not a bulb, is used in the daytime
running lamp (type 2) / position lamp (type
2). Contact a MITSUBISHI MOTORS Au-
thorized Service Point when there is a need for repair or replacement.Daytime running lamps (type
1)*
E01011201137
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
daytime running lamp cover (A) and pry gently to remove it.
Replacement of lamp bulbs
10-33OGAE15E5Maintenance10

Page 392 of 452

2.Remove the screws (B), and then re-
move the lamp unit.
3. Turn the bulb (C) anticlockwise to re-
move it.
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
Rear fog lamp
E01004101596
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-34OGAE15E5Maintenance10

Page 393 of 452

NOTElIf the wiring harness is pulled off the 2 har-
ness guides on the lamp unit while replacingthe bulb, make sure to secure the wiring har-
ness to the harness guides.
l When installing the lamp unit, first insert the
tab (C) into the groove (D) on the body, and then push on the lamp unit to fit it into place.Rear combination lamps
E01004201366
1. Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamp
NOTEl An LED, not a bulb, is used in the stop
lamp/tail lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTEl When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip onthe body and the pin (E) on the unit with the
hole in the body.
Replacement of lamp bulbs
10-35OGAE15E5Maintenance10

Page 394 of 452

Reversing lamps
E01004401430
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
NOTEl Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
cover.
3. Remove the socket and bulb assembly
by turning it anticlockwise.
4. Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.NOTEl When installing the lid, align the tab on the
lid with the hole on the vehicle side.
Replacement of lamp bulbs
10-36OGAE15E5Maintenance10

Page 395 of 452

Licence plate lamps
E01004602093
1. When removing the lamp unit (A), push
it towards the left side of the vehicle
body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
NOTEl When installing the lamp, insert tab (C) first
then align and insert tab (D).High-mounted stop lamp
E01004500593
NOTEl An LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-37OGAE15E5Maintenance10

Page 396 of 452




























OGAE15E5

Page 397 of 452

Vehicle labeling................................................................................ 11-02
Vehicle dimensions........................................................................... 11-05
Vehicle performance......................................................................... 11-07 Vehicle weight.................................................................................. 11-08
Engine specifications........................................................................ 11-11
Electrical system............................................................................... 11-12
Tyres and wheels...............................................................................11-13
Fuel consumption.............................................................................. 11-13
Refill capacities................................................................................. 11-16Specifications
OGAE15E511

Page 398 of 452

Vehicle labelingE01100104747
Vehicle identification number
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
Vehicle information code la-
bel*
The vehicle information code label is located as shown in the illustration.
The label shows model code, engine model,
transmission model and body colour code,
etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Exterior code
4- Transmission model code
5- Body colour code, Interior code,
Option code
6- Chassis number
7- Maximum gross vehicle weight
8- Gross combination weight
9- Maximum axle weight (Front)
10- Maximum axle weight (Rear)
Vehicle labeling
11-02OGAE15E5Specifications11

Page 399 of 452

Vehicle information codeplate*
The vehicle information code plate is riveted
as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code,
etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped on the plate riveted to the left front corner of
the vehicle body. It is visible from outside of
the vehicle through the windscreen.
Engine number
The engine number is stamped on the engine cylinder block as shown in the illustrations.
Vehicle labeling
11-03OGAE15E5Specifications11

Page 400 of 452

Petrol-powered vehicles1600 models
*: Front of the vehicle
1800 models, 2000 models
*: Front of the vehicle
Diesel-powered vehicles
*: Front of the vehicle
*: Front of the vehicle
Vehicle labeling
11-04OGAE15E5Specifications111600 models 2200 models

Page:   < prev 1-10 ... 351-360 361-370 371-380 381-390 391-400 401-410 411-420 421-430 431-440 ... 460 next >