MITSUBISHI ASX 2020 Owner's Manual (in English)

ModeMessageCauseResponseVER ERRORThis iPod/iPhone software version is not supported.Please change to a supported software version.OtherERROR DCAn abnormal direct voltage has been sent to the speak-
ers.Turn the power OFF and wait a short while. If the prob-
lem persists, consult a MITSUBISHI MOTORS Au- thorized Service Point.If You Think Something Is Not Working Properly...
Here is a list of symptoms, causes and responses if you think something is not working properly.
SymptomsCauseResponseThere is no sound or quiet
soundThe volume is turned to its minimum.Adjust the volume.

W “Adjust Volume” on page 7-20The balance or fader is turned to one side.Adjust the balance or fader.

W “Adjust Audio Quality and Volume Balance” on page 7-39The disc cannot be inserted.A disc is already in the product.Eject the disc.

W “Insert/Eject Discs” on page 7-20There is no disc in the product, but the product says it is
loading.Press the eject button once.

W “Insert/Eject Discs” on page 7-20The disc cannot be played.The disc is inserted upside down.Insert with the label side up.The disc has condensation on it.Wait a while before inserting.The disc is dirty.Clean the read surface of the disc.The sound skips in the
same place.The disc is damaged or dirty.Check the disc.There is no sound, even if
the disc is inserted.Damage to or dirt on the disc means that its data cannot be read.Check the disc. Additionally, if using CD-R/RW discs,
their characteristics may render them unable to be played.

Troubleshooting
7-452*$(20(1For pleasant driving7

Link System*
The Link System takes overall control of the devices connected via the USB input terminal
or the Bluetooth

NOTEzSome Bluetooth

HANG-UP button
zPress this button when an incoming call
is received to refuse the call.
z Press this button during a call to end the
current call.
When another call is on hold, you will switch to that call.
z If this button is pressed in the voice rec-
ognition mode, the voice recognition
mode will be deactivated.
NOTEz When you press the SPEECH button to enter
voice recognition mode with a cellular
phone paired to the system, current informa- tion on the cellular phone, such as “remain- ing battery life,” “signal strength” or “roam-
ing,” will be displayed on the audio dis-
play.*
*: Some cellular phones will not send this
information to the Bluetooth

NOTEzChanging the language deletes the mobile
phone book imported to the Bluetooth

NOTEzPassword will be required to access the sys-
tem after the next ignition cycle.
z It is required for a little time after engine
stop that the entered password is actually re-corded in the system.
If the ignition switch or the operation mode
is made to ACC or ON or the engine is star- ted immediately after engine stop, there is a case when the entered password is not recor-
ded in the system. At this time, please try to enter the password again.
Entering the password
If a password has been set and the security
function is enabled, the voice guide will say “Hands-free system is locked. State the pass-word to continue” when the SPEECH button
is pressed to enter voice recognition mode.
Say the 4-digit password number to enter the
password.
If the entered password is wrong, the voice
guide will say “<4- digit password>, Incor-
rect password. Please try again”. Enter the correct password.
NOTEz You can re-enter the password as many
times as you want.NOTEz If you have forgotten your password, say
“Cancel” to quit the voice input mode andthen check with a MITSUBISHI MOTORS
Authorized Service Point.
Disabling the password
Use the following procedure to turn off the
security function by disabling the password.
NOTEz System must be unlocked to disable the
password.
1. Press the SPEECH button.
2. Say “Setup”.
3. Say “Password.”
4. The voice guide will say “Password is
enabled. Would you like to disable it?”
Answer “Yes.”
Answer “No” to cancel the disabling of
the password and return to the main menu.
5. When the disabling of the password is
completed, the voice guide will say “Password is disabled” and the system
will return to the main menu.
Speaker enrollment function
The Bluetooth

NOTEzSpeaker enrollment is not possible unless the
vehicle is parked. Make sure you park the
vehicle in a safe area before attempting speaker enrollment.
2. Press the SPEECH button.
3. Say “Voice training”.
4. The voice guide will say “This operation
must be performed in a quiet environ- ment while the vehicle is stopped. See
the owner

Connecting the Bluetooth

NOTEzThe pairing code entered here is only used
for the Bluetooth

say “The pairing code is <pairing
code>.”NOTEz Some Bluetooth