ABS MITSUBISHI ECLIPSE 1993 User Guide
Page 40 of 57
BODY - FrontBumper
‘plSASSEMBLY ANDREASSEMBLY<EAGLE Talon>
Nmftlbs.
Disassembly steps
@*I)* 1. Bumper absorber
2. Lower plate
3. Front bumper reinforcement
4. Front bumper fascia
19AQ933
NOTE(1) Reverse the disassembly procedures to reassemble.(2) ++ : Refer to “Service Points of Disassembly”(3) l + : Refer to “Service Points of Reassembly”
SERVICE POINTS OF DISASSEMBLY1. REMOVAL OF BUMPER ABSORBER
Caution1. Do not attempt to repair a bumper absorber that has
been compressed in an accident; replace it with a new
one.2. Before discarding the bumper absorber, drill a 3 mm
(. 13 in.) diameter hole to discharge the gas containedin the unit.
3.If the bumper absorber is to be discarded, do not burn
it.
SERVICE POINTS OF REASSEM.BLY1. INSTALLATION OF BUMPER ABSORBER
If the squareness between the front bumper reinforcement
and the bumper absorber is improper, adjust it by putting a
spacer between them.
Page 41 of 57
23-40BODY - Front Buripr<PLYMOUTH
Laser>17-26
Disassembly steps
WI)* 1. Bumper absorber
2. Lower plate
3. Front bumper reinforcement
4. Front bumper
fascia
NOTE(1) Reverse the disassembly procedures to reassemble.(2) W : Refer to “Service Points of Disassembly”.(3) l + : Refer to “Service Points of Reassembly”.
SERVICE POINTS OF DISASSEMBLY1. REMOVAL OF BUMPER ABSORBER
Caution
1. Do not attempt to repair a bumper absorber that has
been compressed in an accident; replace it with a new
one.
2. Before discarding the bumper absorber, drill a 3 mm
(. 13 in.) diameter hole to discharge the gas containedin the unit.
3.If the bumper absorber is to be discarded, do not bum
it.
SERVICE POINTS OF REASSEMBLY1.
INSTALLATiON OF BUMPER ABSORBER
If the squareness between the front bumper reinforcement
and the bumper absorber is improper,
adjusj it by putting a
spacer between them.
Page 44 of 57
-BODY
- Rear Bumper
DISASSEMBLY AND REASSEMBLY
<EAGLE Talon>
Disassembly steps1 Bumper absorber
2 Rear bumper reinforcementNOTE(1) Reverse the disassembly procedures to reassemble.(2)
++ : Refer to “Service Points of Disassembly”.
SERVICE POINTS OF DISASSEMBLY1. REMOVAL OF BUMPER ABSORBER
Caution1. Do not attempt to repair a bumper absorber that has
been con:pressed in an accident; replace it with a new
one.2. Before discarding the bumper absorber, drill a 3 mm
(. 13 in.1 diameter hole to discharge thii gas containedin the unit.
3.If the bumper absorber is to be discarded, do not bum
it.
Page 45 of 57
<PLYMOUTH Laser>
417-26 Nm
18AO948
Disassembly steps1. License plate
light2. Back-up light
3. License plate light wiring harness
4. Bumper absorber
5. Rear bumper reinforcement
6. License plate bracket
7. Rear bumper fascia
SERVICE POINTS OF DISASSEMBLY4. REMOVAL OF BUMPER ABSORBER
2. Before discarding the bumper absorber, drill a 3 mm
L 13 in.) diameter hole to discharge the gas contained
in the unit.
3.If the bumper absorber is to be discarded, do not bumit,. _..2;+ i_.I/~.L I
Caution1. Do not attempt to repair a bumper
absorber that has
been compressed in an accident; replace it with a new
one.