Move MITSUBISHI ECLIPSE 2012 4.G User Guide

Seat and restraint systems
2-15
2
1. Occupants should always sit back in their seats with their
backs against the upright seatback. To reduce the risk of
serious injury or death during deployment of the air bag,
adjust the driver’s seat as far back as possible while main-
taining a position that still enables you to fully apply the
pedals, easily control the steering wheel, and safely oper-
ate the vehicle. The front passenger seat should also be
moved as far back as possible. Refer to “Supplemental
Restraint System (SRS) - air bag” on page 2-36. Also
refer to “To adjust the seat forward or backward” on page
2-5.
WA R N I N G
!
To reduce the risk of serious injury or death in the
event of an accident or sudden stop, all seatbacks
should be kept in the upright position while the vehi-
cle is in motion.
Seat belt performance during an accident can be
adversely affected if the seatbacks are reclined. The
more a seatback is reclined, the more likely seat belt
performance will be adversely affected. If the seat
belt is not properly positioned against the body dur-
ing an accident, there is increased risk you will slide
under the belt and receive serious injury or death.
BK0132701US.book 15 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-19
2
Front passenger seat belt warning light
N00418300093
The front passenger seat belt warning light is located above the
central vents in the instrument panel.
The light normally comes on when the ignition switch is turned
to the “ON” position and goes off a few seconds later.
The light comes on when a person sits on the front passenger
seat but does not fasten the seat belt. It goes off when the seat
belt is subsequently fastened.
Adjustable seat belt shoulder anchor (ECLIPSE
only, front seats)
N00406300230
To move the anchor down, press the lock knob (A) and slide
the anchor down to the desired position.
To move the anchor up, slide the anchor up to the desired posi-
tion.
WA R N I N G
!
Do not install any accessory or sticker that makes
the light difficult to see.
Anchor down Anchor up
BK0132701US.book 19 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-21
2
NOTE
Remove the seat belt from the seat belt guide when a pas-
senger is going to move to or from the rear seat.
Seat belt extender
N00406700087
When your seat belt, even fully extended, is not long enough, a
seat belt extender must be obtained. The extender may be used
for either of the front seats.

Make sure the part of the seat belt webbing you
inserted into the seat belt guide is not twisted.
Twisted webbing may adversely affect seat belt per-
formance.
WA R N I N G
!
WA R N I N G
!
The extender should only be used if the existing belt
is not long enough. Anyone who can use the stan-
dard seat belt should not use an extender. Unneces-
sary use of an extender can adversely affect seat belt
performance in an accident.
When not required, the extender must be removed
and stowed.
BK0132701US.book 21 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-26 Seat and restraint systems
2
WA R N I N G
!
Your vehicle is also equipped with a front passenger
air bag.
Never put REAR-FACING CHILD RESTRAINTS
or INFANT RESTRAINTS in the front passenger
seat. This places the infant too close to the passenger
air bag. During deployment of the air bag, the infant
can be seriously injured or killed. Rear-facing child
restraints or infant restraints must only be used in
the rear seat.
Air bag cover
WA R N I N G
!
FRONT-FACING CHILD RESTRAINTS should
always be used in the rear seat whenever possible. If
one must be used in the front passenger seat, move
the seat to the most rearward position and make
sure the child stays in the child restraint, properly
restrained. Failure to follow these instructions could
result in serious injury or death to the child.
BK0132701US.book 26 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-27
2
NOTE
Before purchasing a child restraint system, try installing it
in the rear seat to make sure there is a good fit. Because of
the location of the seat belt buckles and the shape of the
seat cushion, it may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled forward or to
either side easily on the seat cushion after the seat belt has
been tightened, choose another manufacturer’s child
restraint system.
Depending on the seating position in the vehicle and the
child restraint system that you have, the child restraint can
be attached using one of the following two methods:
• To the lower anchorage in the rear seat ONLY if the
child restraint is compatible with the LATCH system
(See page 2-28).
• To the seat belt (See page 2-31).
WA R N I N G
!
It is important to use an approved rear-facing infant
restraint until the infant is one year old (unless the
infant outgrows the seat sooner). This allows the
infant’s neck and spine to develop enough to support
the weight of their head in the event of an accident.
When installing a child restraint system, follow the
instructions provided by the manufacturer and fol-
low the directions in this manual. Failure to do so
can result in serious injury or death to your child in
an accident or sudden stop.
After installation, push and pull the child restraint
system back and forth, and side to side, to see that it
is firmly secured. If the child restraint system is not
installed securely, it may cause injury to the child or
other occupants in the event of an accident or sud-
den stop.
When not in use, keep your child restraint system
secured with the seat belt, or remove it from the
vehicle, in order to prevent it from being thrown
around inside the vehicle during an accident.
BK0132701US.book 27 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-30 Seat and restraint systems
2
NOTE
In order to secure a child restraint systems compatible
with the LATCH system, use the lower anchor points in
the rear seat. It is not necessary to use the vehicle’s seat
belt.2. Open the rear hatch. Remove the rear shelf panel. Refer to
“Rear shelf panel” on page 3-178.
3. Cut out the notch (F) in the cargo floor carpet by hand,
then lift the carpet.
WA R N I N G
!
If there is any foreign material in or around the
lower anchors, remove it before installing the child
restraint system. Also, make sure the seat belt is
away from, not looped through or otherwise inter-
fering with, the child restraint system. If foreign
matter is not removed and/or the seat belt interferes
with the child restraint system, the child restraint
system will not be secured properly, could detach
and move forward in the event of sudden braking or
an accident, and could result in injury to the child or
other vehicle occupants.
When the vehicle is moving, do not adjust the seat
where the child restraint system is installed.
In an ECLIPSE, install a tether strap in accordance with steps 2 to
4 shown hereafter.
* - Rear of the vehicle
BK0132701US.book 30 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-31
2
4. Latch the tether strap hook (G) of the child restraint sys-
tem to the tether anchor (H) and tighten the tether strap so
it is securely fastened.NOTE
When using a child restraint system that requires a tether
strap, the rear shelf panel cannot be installed.
5. Push and pull the child restraint system in all directions to
be sure it is firmly secured.
Installing a child restraint system using the seat
belt (With emergency/automatic locking mecha-
nism)
N00407300413
With the exception of the driver, the seat belt in all other seat-
ing positions can be converted from normal Emergency Lock-
ing Retractor (ELR) mode to Automatic Locking Retractor
(ALR) mode. This means that when you pull the seat belt fully
out of the retractor, the retractor will switch to its ALR child
restraint installation function. Always use the ALR child
restraint installation function when you install a child restraint
system using the seat belt.
Children 12 years old and under should always be restrained in
the rear seat, whenever possible, although the front passenger
seat belt can also be converted to ALR mode.
WA R N I N G
!
Child restraint tether anchors are designed only to
withstand loads from correctly fitted child restraint
systems. Under no circumstances are they to be used
for adult seat belts, or harnesses, or for attaching
other items or equipment to the vehicle.
WA R N I N G
!
When you install a child restraint system using the
seat belt, always make sure the retractor has been
switched to the ALR child restraint installation
function. The ALR function will keep the child
restraint system tightly secured to the seat.
Failure to convert the retractor to the ALR function
may allow the child restraint system to move for-
ward during sudden braking or an accident, result-
ing in serious injury or death to the child or other
occupants.
[ECLIPSE SPYDER only]
Before attaching a child restraint system to the front
passenger seat, insert the seat belt into the seat belt
guide. Refer to “Seat belt guide” on page 2-20.
BK0132701US.book 31 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-33
2
5. After confirming that the belt is locked, grab the shoulder
part of the belt near the buckle and pull up to remove any
slack from the lap part of the belt allowing the slack to
feed into the retractor. Remember, if the lap belt portion is
not tight, the child restraint system will not be secure. It
may help to put your weight on the child restraint system
and/or push on its seatback while pulling up on the belt
(see illustration). 6. Open the rear hatch. Remove the rear shelf panel. Refer to
“Rear shelf panel” on page 3-178.
7. Cut out the notch (A) in the cargo floor carpet by hand,
then lift the carpet.In an ECLIPSE, if your child restraint system requires the use of
a tether strap fasten the tether strap in accordance with steps 6 to
8 shown hereafter.
* - Rear of the vehicle
BK0132701US.book 33 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-34 Seat and restraint systems
2
8. Latch the tether strap hook (B) of the child restraint sys-
tem to the tether anchor (C) and tighten the tether strap so
it is securely fastened.NOTE
When using a child restraint system that requires a tether
strap, the rear shelf panel cannot be installed.9. Before putting your child in the restraint, push and pull
the restraint in all directions to be sure it is firmly secured.
Do this before each use. If the child restraint system is not
firmly secure, repeat steps 1 through 8.
10. To remove a child restraint system from the vehicle and
deactivate the ALR mode, remove the child from the
restraint. Unlatch the buckle. Then remove the belt from
the restraint and let the belt fully retract.
WA R N I N G
!
Child restraint tether anchors are designed only to
withstand loads from correctly fitted child restraint
systems. Under no circumstances are they to be used
for adult seat belts, or harnesses, or for attaching
other items or equipment to the vehicle.
BK0132701US.book 34 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-36 Seat and restraint systems
2Supplemental Restraint System (SRS) - air
bag
N00407700606
This vehicle is equipped with a Supplemental Restraint System
(SRS), which includes air bags for the driver and front passen-
ger.
The SRS front air bags are designed to supplement the primary
protection of the driver and front passenger seat belt systems
by providing those occupants with protection against head and
chest injuries in certain moderate to severe frontal collisions.
The SRS front air bags, together with the sensors at the front of
the vehicle and sensors attached to the front seats, form an
advanced air bag system.
In an ECLIPSE, the SRS side air bags are also designed to sup-
plement the seat belts and provide the driver and front passen-
ger with protection against chest and abdomen injuries in
certain moderate to severe side impact collisions.
In an ECLIPSE SPYDER, the SRS side air bags are also
designed to supplement the seat belts and provide the driver
and front passenger with protection against head and chest
injuries in certain moderate to severe side impact collisions.The SRS curtain air bags (ECLIPSE only) are designed to sup-
plement the seat belts and provide the driver and front passen-
ger with protection against head injuries in certain moderate to
severe side impact collisions.
The SRS air bags are NOT a substitute for use of the seat belts.
For maximum protection in all types of accidents, seat belts
must ALWAYS be worn by everyone who drives or rides in
this vehicle (with infants and small children in an appropriate
child restraint in the rear seat, and older children buckled in the
rear seat). Refer to “Child restraints” on page 2-24.
WA R N I N G
!
IT IS VERY IMPORTANT TO ALWAYS WEAR
YOUR SEAT BELT PROPERLY EVEN WITH AN
AIR BAG.
• Seat belts help keep the driver and front passenger
properly positioned. This reduces the risk of injury
in all collisions, and reduces the risk of serious
injuries or death when the air bags inflate.
During sudden braking just before a collision, an
unrestrained or improperly restrained driver or
front passenger can move forward into direct con-
tact with, or within close proximity to, the air bag
when it begins to inflate.
The beginning stage of air bag inflation is the most
forceful and can cause serious injuries or death if
the occupant comes in contact with the air bag at
this time.
• Seat belts reduce the risk of injury in rollovers,
rear impact collisions, and in lower-speed frontal
collisions, because the air bags are not designed to
inflate in those situations.
• Seat belts reduce the risk of being thrown from
your vehicle in a collision or rollover.
BK0132701US.book 36 ページ ２０１０年１２月６日　月曜日　午後２時３分