clock MITSUBISHI iMiEV 2012 1.G User Guide

Comfort controls
5-41
5 Clock
(if so equipped)
N00755000124
The time is displayed when the electric motor switch is in the
“ON” or “ACC” position.To set the time1. Press and hold the clock button and the clock display
flashes.
2. Press the SEEK button to adjust the “hours” digit.
If you keep pressing the button, fast-forward begins.3. When the “hours” digit is adjusted, press the clock button
to flash the “minutes” digit.
Press the SEEK button to adjust the “minutes” digit.
If you keep pressing the button, fast-forward begins.
4. When the time is set, press the clock button to stop the
clock display from flashing.
NOTE
Reset the time after the 12V starter battery terminals are
disconnected and reconnected.

Seconds do not appear in the clock display, but after
adjusting the “minutes” setting, the clock begins to oper-
ate from 0 seconds.
A- Clock button
B- SEEK (clock adjustment up) button
C- SEEK (clock adjustment down) button
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-13
6
9. Remove the valve insert (J) by turning it counterclockwise
using the valve remover (I). Put the removed valve insert
in a clean place so it does not get dirty.NOTE
Turn the valve remover by hand. If you use a tool, the
valve remover could be damaged.10. Remove the plug (K) from the free end of the hose (L).
Press the hose onto the valve (H).
WA R N I N G
!
If there is any air left in the tire when you remove
the valve insert, the valve insert may fly out and
injure you. Make sure the tire contains no air before
removing the valve insert.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-8 Vehicle care and maintenance
7
2. Peel off the Velcro fastener (A) to remove the luggage
room floor carpet (B).NOTE
A heat insulating material is attached to the luggage room
floor carpet. To remove the luggage floor carpet, grasp
and lift up both the carpet fabric and the heat insulating
material.3. Turn the 4 screws on the front and rear of the electric
motor unit room lid (C) counterclockwise to loosen and
remove them, and then remove the electric motor unit
room lid (C).
NOTE
When laying the electric motor unit room lid on the
ground, leave the underside of the lid with the rubber sur-
face facing up. If the underside is facing downward debris
and other foreign material could get on the rubber surface
and prevent proper reinstallation of the electric motor unit
room lid.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-13
7 12V starter battery
N00939100914
The condition of the 12V starter battery is very important to
keep the vehicle’s electrical system working properly. Check
the 12V starter battery regularly. Removing and installing the 12V starter battery
upper cover
N00901300054
To r e m o v e1. Turn the plastic nut (A) counterclockwise, and then
remove the 12V starter battery upper cover (B).NOTE
Be careful not to lose the removed plastic nut.
To i n s t a l l1. Install the 12V starter battery upper cover (B) onto the
12V starter battery, and then push the plastic nut (A) in the
direction shown by the arrows to secure the cover.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-38 Vehicle care and maintenance
7
Front side-marker lights
N00915500161
1. Insert a flat blade screwdriver into the end of the light
nearer the rear of the body and pry gently to remove the
light.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. Remove the socket and bulb assembly together by turning
it counterclockwise.*: Front of the vehicle
*
BK0140800US.book 38 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-40 Vehicle care and maintenance
7
Front turn signal lights/Front fog lights (if so
equipped)/Daytime running lights
(if so equipped)
N00943400312
1. To create enough work space, turn the steering wheel all
the way in the same direction to the side you wish to
replace.
2. Remove the clip (A) and bolts (B), then lift the cover (C).3. Turn the socket counterclockwise to remove it.
D- Front turn signal light
E- Front fog light
F- Daytime running light
BK0140800US.book 40 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-43
7
4. Turn the socket counterclockwise to remove it.NOTE
The tail and stop lights use LEDs rather than bulbs.
For repair and replacement, contact a certified i-MiEV
dealer.5. Pull the bulb out of the socket.
6. To install the bulb, perform the removal steps in reverse.C- Tail and stop light (LED) - cannot be replaced
D- Rear turn signal light
E- Back up light
BK0140800US.book 43 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-44 Vehicle care and maintenance
7
Rear side-marker lights
N00935400108
1. Remove the clips (A), then lift the cover (B).2. Turn the socket (C) counterclockwise to remove it.
3. Pull the bulb out of the socket.
BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Alphabetical index
2
C
California Perchlorate Materials Requirements 1-9
Capacities 9-10
Card holder 3-123
,3-129
Cargo loads 4-13
Certification label 9-5
Charging
Quick charging 1-33
Regular charging 1-20
,1-32
Charging indicator 3-72
Charging Timer 1-48
Charging troubleshooting guide 1-38
Chassis number 9-3
Child restraint 2-23
Child safety locks for rear door 3-15
Cleaning
Inside of your vehicle 7-50
Outside of your vehicle 7-52
Clock 5-41
Cold
Cautions and actions to deal with intense cold 1-12
Combination headlights and dimmer switch 3-76
Consumer information 8-2
Coolant 7-7
,9-10
Cruising range 1-5
Cruising range indicator 3-61
,3-67
Cup holder 3-130
D
Dash lights brightness indicator 3-61
,3-66
Daytime running lights
Bulb capacity 7-36
Replacement 7-40
Defogger (rear window) 3-89
Dimensions 9-6
Dimmer (high/low beam change) 3-81
Dinghy towing 4-14
Disc brake pads 7-27
Dome light (Front)/Reading lights
Bulb capacity 7-37
Switch 3-125
Dome light (Rear)
Bulb capacity 7-37
Switch 3-127
Door-ajar warning light and buzzer 3-74
Doors
Lock 3-12
Power door locks 3-14
Driver’s seat belt reminder/warning light 2-17
Driving during cold weather 4-7
Driving, alcohol and drugs 4-3
E
Economical driving 4-2
Electric motor
Number 9-4
BK0140800US.book 2 ページ ２０１１年９月２９日　木曜日　午後３時２８分