oil MITSUBISHI LANCER 2005 Owners Manual

DOOR
BODY42-25
DOOR
SERVICE SPECIFICATIONSM1423000300091
SEALANTM1423000500095
SPECIAL TOOLSM1423000600337
ItemStandard value
Power window operation current (Power supply voltage 14.5 ± 0.5 V, at 25 °C) A 5 ± 1
Door outside handle play mm Front door 2.6 ± 2.5
Rear door 1.3 ± 1.3
Door inside handle play mm Front door 10.4 ± 9.6
Rear door 10 ± 9.6
Item Specified sealant
Door waterproof film 3M ATD Part No.8633 or equivalent
Tool Number Name Use
MB990480 Window glass holder Removal of power window regulator
assembly
MB990900 or
MB991164Door hinge adjusting
wrenchDoor alignment
MB990925
A: MB990939Bearing and oil seal
installer set
A: Brass barDoor striker adjustment
MB990211 Sliding hammer
MB990241
A: MB990243Axle shaft puller
A: Body puller
MB990480
MB990900
MB990925AF
A
MB990211
MB990241
A
AE

TRUNK LID
BODY42-43
TRUNK LID
REMOVAL AND INSTALLATIONM1421002200180
AC301676
Y0636AU
Y0637AU
AB
1
2
3
45
5
6
7 89
10
99
11
12
8.9 ± 1.9 N·m A
A
B
B15 mm
14 mm
5Section A - A
Section B - B
Trunk lid weatherstrip removal steps
•Rear end trim (Refer to GROUP 52A,
Trims P.52A-11.)
>>B<<1. Trunk lid weatherstrip
Trunk lid release cable and trunk lid
release handle removal steps
•Rear end trim (Refer to GROUP 52A,
Trims P.52A-11.)
•Trunk rear side trim (LH) (Refer to
GROUP 52A, Trims P.52A-11.)
•Front scuff plate (LH) (Refer to
GROUP 52A, Trims P.52A-11.)
•Cowl side trim (LH) (Refer to GROUP
52A, Trims P.52A-11.)
•Rear scuff plate (LH) (Refer to
GROUP 52A, Trims P.52A-11.)
•Centre pillar lower trim (Refer to
GROUP 52A, Trims P.52A-11.)
•Rear seat (Refer to GROUP 52A,
Rear seat assembly P.52A-28.)
•Accelerator pedal stopper (Refer to
GROUP 17, Accelerator pedal
P.17-3.)
2. Trunk lid release handle
3. Trunk lid release cableTrunk lid striker removal steps
•Rear end trim (Refer to GROUP 52A,
Trims P.52A-11.)
4. Trunk lid striker
Trunk lid panel removal steps
•Licence plate garnish (Refer to
GROUP 51, Garnishes P.51-17.)
5. Trunk lid bumper
•Rear spoiler (Refer to GROUP 51,
Rear spoiler P.51-18.)
6. Trunk lid lock cylinder
7. Trunk lid latch assembly
8. Trunk lid hinge mounting bolt
9. Trunk lid panel assembly
Trunk lid latch removal
7. Trunk lid latch assembly
Trunk lid hinge removal steps
•Rear shelf trim (Refer to GROUP
52A, Trims P.52A-11.)
•Rear seat (Refer to GROUP 52A,
Rear seat assemblyP.52A-28.)
9. Trunk lid panel assembly
<<A>> >>A<<10. Trunk lid torsion bar (RH)
<<A>> >>A<<11. Trunk lid torsion bar (LH)
12. Trunk lid hinge

TRUNK LID
BODY42-45
CAUTION
Install the trunk lid torsion bar <LH> before the
trunk lid torsion bar <RH>. If the sequence is
reversed, the trunk lid torsion bar <LH> will not
be able to be installed because the special tool
will interfere with the trunk lid torsion bar <RH>
during installation of the trunk lid torsion bar
<LH>.
1. Identify the LH and RH torsion bars by the colour
mark made at the centre of each torsion bar.
2. Insert the left end of the trunk lid torsion bar <LH>
in the hole in the trunk lid hinge <LH>.
3. Press portion A of the trunk lid torsion bar <LH>
right end against point A on the trunk lid hinge
<RH> as shown in View F in the drawing.
4. Twist the portion B of the trunk lid torsion bar
<LH> right end using the special tool until it is
moved from point B and pressed against point C
of the trunk lid hinge <RH> as shown in View F.
Then force the portion into point D.
5. Twist the portion A of the trunk lid torsion bar
<LH> right end until it reaches point E on the trunk
lid hinge <RH> as shown in View F.
6. Attach the trunk lid torsion bar <RH> to the trunk
lid hinge <LH> using the same method as the
trunk lid torsion bar <LH>.
>>B<< TRUNK LID WEATHERSTRIP
INSTALLATION
Install the trunk lid weatherstrip so that the marking
and the joint are aligned with the body centre line,
INSPECTIONM1421004800133
TRUNK LID LATCH SWITCH CONTINUITY
CHECK
Trunk lid torsion bar Mark
colour
LH Vehicles with rear spoiler Green
Vehicles without rear spoiler White
green
RH Vehicles with rear spoiler Yellow
Vehicles without rear spoiler Red
Switch position Tester
connectionSpecified
condition
ON (Latch open) 1 − Earth Less than 2
ohms
OFF (Latch shut) Open circuit
AC006104AB Joint
section
Marking
section
AC305142AB
Trunk lid latch assembly

TA I L G AT E
BODY42-48
TAILGATE
REMOVAL AND INSTALLATIONM1424001100178
CAUTION
•Do not disassemble or throw the tailgate gas spring into fire.
•Punch a hole in the gas spring before disposal to release the gas inside.
•Ensure the tailgate gas spring piston rod does not come into contact with foreign material.
Pre-removal Operation
•Tailgate Spoiler Assembly Removal (Refer to GROUP 51,
Tailgate Spoiler P.51-19).
•Tailgate Trim Assembly Removal (Refer to GROUP 52A,
Tailgate Trim P.52A-19).
•Rear Wiper Motor Removal (Refer to GROUP 51, Rear
Wiper and Washer P.51-29).Post-installation Operation
•Tailgate Fit Adjustment (Refer to P.42-46).
•Rear Wiper Motor Installation (Refer to GROUP 51, Rear
Wiper and Washer P.51-29).
•Tailgate Trim Assembly Installation (Refer to GROUP
52A, Tailgate Trim P.52A-19).
•Tailgate Spoiler Assembly Installation (Refer to GROUP
51, Tailgate Spoiler P.51-19).
AC304836
7
3
4 1
6
8
12 ± 2 N·m
13 ± 2 N·m22 ± 4 N·m
AB
Sealant: 3M ATD Part No. 8633 or equivalent9.0 ± 2.0 N·m
2
712 ± 2 N·m
5
7
9
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
3
11
10

51-1
GROUP 51
EXTERIOR
CONTENTS
FRONT BUMPER ASSEMBLY . . . . .51-2
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-2
FRONT BUMPER ASSEMBLY . . . . . . . . . . 51-2
REMOVAL AND INSTALLATION . . . . . . . . 51-2
DISASSEMBLY AND REASSEMBLY . . . . . 51-3
REAR BUMPER ASSEMBLY . . . . . .51-5
REMOVAL AND INSTALLATION . . . . . . . . 51-5
DISASSEMBLY AND REASSEMBLY . . . . . 51-7
MOULDINGS . . . . . . . . . . . . . . . . . . .51-9
SPECIAL TOOL . . . . . . . . . . . . . . . . . . . . . 51-9
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-9
MOULDINGS . . . . . . . . . . . . . . . . . . . . . . . 51-10
REMOVAL AND INSTALLATION . . . . . . . . 51-10
SIDE AIR DAM . . . . . . . . . . . . . . . . . .51-15
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-15
SIDE AIR DAM . . . . . . . . . . . . . . . . . . . . . . 51-15
REMOVAL AND INSTALLATION . . . . . . . . 51-15
GARNISHES . . . . . . . . . . . . . . . . . . .51-17
REMOVAL AND INSTALLATION . . . . . . . . 51-17
REAR SPOILER . . . . . . . . . . . . . . . . .51-18
REMOVAL AND INSTALLATION . . . . . . . . 51-18
TAILGATE SPOILER . . . . . . . . . . . . .51-19
REMOVAL AND INSTALLATION . . . . . . . . 51-19
ROOF RAIL . . . . . . . . . . . . . . . . . . . .51-20
REMOVAL AND INSTALLATION . . . . . . . . 51-20
WINDSHIELD WIPER AND WASHER51-21
GENERAL INFORMATION . . . . . . . . . . . . . 51-21
SERVICE SPECIFICATION . . . . . . . . . . . . 51-22TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-22
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . 51-22
WINDSHIELD WIPER AND WASHER . . . . 51-23
REMOVAL AND INSTALLATION . . . . . . . . 51-23
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-25
REAR WIPER AND WASHER . . . . . .51-28
GENERAL INFORMATION . . . . . . . . . . . . . 51-28
SERVICE SPECIFICATION . . . . . . . . . . . . 51-28
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-28
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . 51-28
REAR WIPER AND WASHER . . . . . . . . . . 51-29
REMOVAL AND INSTALLATION . . . . . . . . 51-29
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-30
HEADLAMP WASHER . . . . . . . . . . . .51-32
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-32
HEADLAMP WASHER . . . . . . . . . . . . . . . . 51-32
REMOVAL AND INSTALLATION . . . . . . . . 51-32
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-33
MARK . . . . . . . . . . . . . . . . . . . . . . . . .51-34
REMOVAL AND INSTALLATION . . . . . . . . 51-34
DOOR MIRROR . . . . . . . . . . . . . . . . .51-36
GENERAL INFORMATION . . . . . . . . . . . . . 51-36
SERVICE SPECIFICATION . . . . . . . . . . . . 51-36
SPECIAL TOOL. . . . . . . . . . . . . . . . . . . . . . 51-36
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-36
DIAGNOSIS TROUBLESHOOTING
FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-36
TROUBLE SYMPTOM CHART . . . . . . . . . . 51-36
SYMPTOM PROCEDURES . . . . . . . . . . . . 51-37
DOOR MIRROR . . . . . . . . . . . . . . . . . . . . . 51-45
REMOVAL AND INSTALLATION . . . . . . . . 51-45
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-47

REAR SPOILER
EXTERIOR51-18
REAR SPOILER
REMOVAL AND INSTALLATIONM1511006100136
REMOVAL SERVICE POINT
<<A>> HIGH-MOUNTED STOP LAMP
REMOVAL
Use the following steps to easily route high-mounted
stop lamp harness in the event of installation:
CAUTION
Ensure that the string is tightly tied.
1. Tie string on high-mounted stop lamp harness (at
connector side).
2. Carefully pull out high-mounted stop lamp.
AC303713
2 3
4
2
1
AB
1
Removal steps
•Trunk lid bumper (Refer to GROUP
42, Trunk lid P.42-43.)
1. Cap2. Gasket
3. Rear spoiler
<<A>>4. High-mounted stop lampRemoval steps (Continued)
AC303708
Connector String
AB

TAILGATE SPOILER
EXTERIOR51-19
TAILGATE SPOILER
REMOVAL AND INSTALLATIONM1511019900068
AC303721
1
2 3
AB
5.2 ± 1.0 N·m
Tailgate spoiler removal steps
•Tailgate trim upper (Refer to GROUP
52A, Tailgate trim P.52A-19.)
•High-mounted stoplight connector
connection•Rear washer hose connection
1. Tailgate spoiler assembly
2. High-mounted stoplight assembly
3. Tailgate spoiler Tailgate spoiler removal steps

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-82
AC304750AB
12 <With rear spoiler>
Removal steps
1. Rear spoiler (Refer to GROUP 51,
Rear spoiler P.51-18.)
<<A>>2. High-mounted stop lamp

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-83
<Wagon>
REMOVAL SERVICE POINT
<<A>> HIGH-MOUNTED STOP LIGHT
REMOVAL <WITH REAR SPOILER>
Use the following steps to easily route high-mounted
stop light harness in the event of installation:
CAUTION
Ensure that the string is tightly tied.
1. Tie a string on the high-mounted stop light
harness (at the connector side).
2. Carefully pull out the high-mounted stop light.
AC304722AB
2
1
Removal steps
•Tailgate trim upper (Refer to
GROUP 52A, Tailgate trim
P.52A-19.)
•High-mounted stop lamp connector
connection
•Rear washer hose connection
(Refer to GROUP 51, Rear wiper
and washer P.51-29.)1. Tailgate spoiler (Refer to GROUP
51, Tailgate spoiler P.51-19.)
•Rear washer nozzle (Refer to
GROUP 51, Rear wiper and
washer P.51-29.)
2. High-mounted stop lampRemoval steps (Continued)
AC005190
String
Connector
AC

55-2
ON-VEHICLE SERVICE . . . . . . . . . . .55-69
SIGHT GLASS REFRIGERANT
LEVEL TEST . . . . . . . . . . . . . . . . . . . . . . . . 55-69
MAGNETIC CLUTCH TEST . . . . . . . . . . . . 55-69
COMPRESSOR DRIVE BELT
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . 55-69
DUAL PRESSURE SWITCH CHECK . . . . . 55-69
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . 55-70
CORRECTING LOW REFRIGERANT LEVEL
IN CASE THE SERVICE CAN IN USED. . . 55-72
DISCHARGING SYSTEM . . . . . . . . . . . . . . 55-72
REFILLING OF OIL IN THE A/C
SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-72
PERFORMANCE TEST . . . . . . . . . . . . . . . 55-73
REFRIGERANT LEAK REPAIR
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . 55-74
COMPRESSOR NOISE CHECK . . . . . . . . 55-74
POWER RELAY CHECK . . . . . . . . . . . . . . 55-75
IDLE-UP OPERATION CHECK . . . . . . . . . 55-76
CLEAN AIR FILTER REPLACEMENT
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . 55-76
HEATER CONTROL ASSEMBLY AND A/C
SWITCH . . . . . . . . . . . . . . . . . . . . . . .55-77
REMOVAL AND INSTALLATION . . . . . . . . 55-77
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . 55-79
DISASSEMBLY AND REASSEMBLY . . . . . 55-79
HEATER UNIT, HEATER CORE,
BLOWER ASSEMBLY AND
EVAPORATOR UNIT* . . . . . . . . . . . .55-81
REMOVAL AND INSTALLATION . . . . . . . . 55-81
HEATER UNIT . . . . . . . . . . . . . . . . . . . . . . 55-82
DISASSEMBLY AND REASSEMBLY
<L.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-82
DISASSEMBLY AND ASSEMBLY
<R.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-83
BLOWER ASSEMBLY . . . . . . . . . . . . . . . . 55-84
DISASSEMBLY AND REASSEMBLY . . . . . 55-84
BLOWERMOTOR, RESISTOR AND
OUTSIDE/INSIDE AIR SELECTION
DAMPER CONTROL MOTOR . . . . . .55-85
REMOVAL AND INSTALLATION . . . . . . . . 55-85
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 55-86
EVAPORATOR ASSEMBLY . . . . . . .55-88
REMOVAL AND INSTALLATION
<L.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-88
REMOVAL AND INSTALLATION
<R.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-89
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 55-90
COMPRESSOR ASSEMBLY AND
TENSION PULLEY . . . . . . . . . . . . . . .55-91
REMOVAL AND INSTALLATION . . . . . . . . 55-91
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 55-93
DISASSEMBLY AND REASSEMBLY . . . . . 55-94
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 55-95
CONDENSER AND CONDENSER
FAN MOTOR . . . . . . . . . . . . . . . . . . . .55-96
REMOVAL AND INSTALLATION . . . . . . . . 55-96
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 55-97
REFRIGERANT LINE . . . . . . . . . . . . .55-98
REMOVAL AND INSTALLATION
<L.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-98
REMOVAL AND INSTALLATION
<R.H.D.> . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-99
DUCTS . . . . . . . . . . . . . . . . . . . . . . . .55-101
REMOVAL AND INSTALLATION . . . . . . . . 55-101
VENTILATORS . . . . . . . . . . . . . . . . . .55-102
REMOVAL AND INSTALLATION . . . . . . . . 55-102