clip MITSUBISHI LANCER 2005 Owner's Manual

WINDOW GLASS
BODY42-19
QUARTER WINDOW GLASS
REMOVAL AND INSTALLATIONM1422002500247
Pre-removal and Post-installation Operation
•Quarter Trim Upper Removal and Installation (Refer to
GROUP 52A, Trims P.52A-11).
AC304783
N
N
N
12
3
N3 4
AB
Y1509AU
Y1508AU
Y1507AU
Y1485AU
Y1535AU
AC304784
AAB B
DD
C
C
Mark
Apply the primer and adhesive
along the fictitious lines (seal line)
between each of the marks.
Adhesive: 3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or equivalent and
3M ATD Part No. 8608 Super Fast Urethane Primer or equivalent
1 11
Seal line centrePrimer Section A – A Section B – BSeal line
centre
Primer
Section C – C Section D – D
Seal line
centrePrimer
1Seal line
centre
Units: mm
Primer
16
161616
Ceramic line
AB
Removal steps
<<A>> >>B<<1. Quarter window glass assembly
>>A<<2. Dual lock fastener
>>A<<3. Clip
>>A<<4. GasketRemoval steps (Continued)

WINDOW GLASS
BODY42-21
INSTALLATION SERVICE POINTS
>>A<< GASKET/CLIP/DUAL LOCK
FASTENER INSTALLATION
1. Carry out the following procedure to re-install
quarter window glass.
CAUTION
Do not forget gasket.
(1) Fit clips into body.
(2) Cut away clip fitting convex on quarter window
glass.
NOTE: Convex gets broken when quarter
window glass is removed.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the quarter window glass and the body
flanges.
3. Assemble the dual lock fastener according to the
standard location of the body flange.
4. Assemble the dual lock fastener to the quarter
window glass relative to the body flange dual lock
fastener.
>>B<< QUARTER WINDOW GLASS
INSTALLATION
Remove the quarter window glass using the same
procedure as for the windshield removal (Refer to
P.42-12).
AC103606
AC
Cut off these convex parts
AC304793AB
Dual lock fastener
Install the dual lock fastener
with aligning it onto the bumps
of the body flange.

DOOR
BODY42-30
DOOR INSIDE HANDLE PLAY
ADJUSTMENT
M1423001500292
1. Check that the door inside handle play is within
the standard value range.
Standard value (B):
Front door: 10.4 ± 9.6 mm
Rear door: 10 ± 9.6 mm2. If the door inside handle play is outside the
standard value range.
3. Remove the door trim assembly (Refer to GROUP
52A, Door trim P.52A-15).
4. Remove the waterproof film (Refer to P.42-39).
5. Adjust the door inside handle play with the outer
cable end connecting the door inside handle and
inside lock cable.
AC006114Y0705AUAB
A
A
BSection A – A
AC100404
AB
Clip Inner cable
Outer cable end
Inside handle rodDoor inside handle

DOOR
BODY42-33
AC305108
NOTE
: Clip positions
: Claw positions
View A
B
B
B
B C
CC
CC
CC
C
Section B - B <FRONT DOOR>
Door trim
ClipSection C - C
AB
Door trim
Claw
7
7
7 7
A
AC305109
NOTE
: Clip positions
: Claw positions
E
E
E
E F
FF
FF
FF
F
Section E - EView D
Door trim
ClipSection F - F
Door trim
Claw
D
<REAR DOOR>
7
7 7
AB
7
Door window regulator assembly
removal steps
•Door trim assembly (Refer to GROUP
52A, Door Trim P.52A-15.)
•Waterproof film (Refer to P.42-39.)
<<A>> >>B<<1. Window regulator assembly
<<A>> >>B<<2. Power window motor assembly
Door window glass removal steps
•Window glass runchannel (Refer to
P.42-39.)
3. Door window glassStationary window glass removal
steps
•Window glass runchannel (Refer to
P.42-39.)
•Door beltline inner weatherstrip
(Refer to P.42-39.)
3. Door window glass<<B>> >>A<<4. Centre sash upper
5. Stationary window glass
6. Stationary window weatherstrip
Power window switch removal steps
7. Power window switch panel assembly

DOOR
BODY42-37
INSTALLATION SERVICE POINTS
>>A<< DOOR CHECK INSTALLATION
Install the door check so that the identification mark
faces upwards.
>>B<< LOWER SASH INSTALLATION
Securely insert the rear lower sash into the window
rear sash.
>>C<< DOOR INSIDE HANDLE
INSTALLATION
1. Install the inside lock cable to the door inside
handle as follows:
(1) Install the inner cable end in the inside lock
cable to the clip in the door inside handle.
(2) Turn the inside lock knob to the door lock
position.
(3) Install the outer cable end to the door inside
handle securely.
(4) Install the clip to the inner cable.2. Install the inside handle rod to the door inside
handle.
3. Install the door inside handle to the door.
INSPECTIONM1423004700392
FRONT DOOR LOCK ACTUATOR CHECK
Actuator Operation Check Item Identification
mark
Front Door Left door 39L
Right door 39R
Rear Door Left door 40L
Right door 40R
ACX00541
Identification mark
AB
AC100404
AB
Clip Inner cable
Outer cable end
Inside handle rodDoor inside handleLever
positionBattery connection Lever
operation
At the
"LOCK"
position•Connect terminal
No. 4 and the
negative battery
terminal.
•Connect terminal
No. 6 and the
positive battery
terminal.The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position•Connect terminal
No. 6 and the
negative battery
terminal.
•Connect terminal
No. 4 and the
positive battery
terminal.The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
42
53
6 1
42
53
6 1
AC305111B
A
AB
LockUnlock
View A
View B Unlock
Lock Front door<Left side>
<Right side>Lever
Lever

DOOR
BODY42-39
WINDOW GLASS RUNCHANNEL AND
DOOR OPENING WEATHERSTRIP
REMOVAL AND INSTALLATIONM1423003100290
<FRONT DOOR>
AC304409AB
Section A – A
<Front door>
Sealant: 3M ATD Part No.8633 or equivalentDoor
: Sectional view of
clip position
: Sectional view of
clip position
6 2
1
4
365
A A
1
Waterproof film removal steps
•Door trim assembly, speaker (Refer to
GROUP 52A, Trims P.52A-11).
1. Waterproof film
Door inner opening weatherstrip
removal steps
•Scuff plate, centre pillar lower trim
and cowl side trim (Refer to GROUP
52A, Trims P.52A-11.)
2. Door inner opening weatherstrip
(Body side)
Door outer opening weatherstrip
removal steps
•Front door check mounting bolt (Door
side) (Refer to P.42-31.)
<<A>> >>A<<3. Door outer opening weatherstripDoor window glass runchannel
removal
4. Door window glass runchannel
Door beltline inner weatherstrip
removal steps
•Front door trim(Refer to GROUP 52A,
Door trim P.52A-15.)
5. Door beltline inner weatherstrip
Door beltline moulding removal steps
•Door mirror assembly (Refer to
GROUP 51, Door mirror P.51-45.)
•Door window glass (Refer to
P.42-32.)
6. Door beltline moulding

DOOR
BODY42-40
<REAR DOOR>
AC304418AB
Section A – A
Door
: Sectional view of
clip position
: Sectional view of
clip position
6 2 4
5
7
A A
3
Section B – B <Rear door>
Door
6
3
6
BB
Sealant: 3M ATD Part No.8633 or equivalent
1
1
Waterproof film removal steps
•Door trim assembly (Refer to GROUP
52A, Door trim P.52A-15).
1. Waterproof film
Door inner opening weatherstrip
removal steps
•Scuff plate, centre pillar lower trim
and cowl side trim (Refer to GROUP
52A, Trims P.52A-11.)
2. Door inner opening weatherstrip
(Body side)
Door outer opening weatherstrip
removal steps
•Rear door check mounting bolt (Door
side) (Refer to P.42-31.)
3. Retainer weatherstrip
<<A>> >>A<<4. Door outer opening weatherstripDoor window glass runchannel
removal
5. Door window glass runchannel
Door beltline inner weatherstrip
removal steps
•Rear door trim (Refer to GROUP 52A,
Door trim P.52A-15.)
•Centre sash upper (Refer to P.42-32.)
6. Door beltline inner weatherstrip
Door beltline moulding removal steps
•Door window glass (Refer to
P.42-32.)
•Stationary glass (Refer to P.42-32.)
7. Door beltline moulding

TRUNK LID
BODY42-41
REMOVAL SERVICE POINT
<<A>> DOOR OUTER OPENING
WEATHERSTRIP REMOVALMake a fabricated tool as shown in the illustration to
remove the door weatherstrip.
INSTALLATION SERVICE POINT
>>A<< DOOR OUTER OPENING
WEATHERSTRIP INSTALLATION
The clip colour identifies the left and right
weatherstrips so be sure to use the colours so as to
install correctly.
TRUNK LID
SPECIAL TOOLM1421000600245
ON-VEHICLE SERVICE
TRUNK LID ADJUSTMENTM1421001000042
1. If the clearance around the trunk lid panel
assembly is not uniform and locking and
unlocking of the trunk lid is difficult, make
adjustments to the trunk lid bumpers (refer to
P.42-42) and trunk lid hinges (refer to P.42-42).
2. If the clearance around the trunk lid panel
assembly is uniform, but locking and unlocking of
the trunk lid is difficult, make adjustments to the
trunk lid bumpers (refer to P.42-42) and trunk lid
striker (refer to P.42-42).
ACX00555
15 mm
8 mm
AB
4 mm
Thickness:
1 mm
Fabricated
tool
Applicable side Identification colour
Right door Pink
Left door Natural (White)
TOOL Number Name Use
MB991244 Torsion bar remover and
installerRemoval and installation of
trunk lid torsion bar
MB991244
AC202324
AC202325AC202913
A
A AA
AB
Section A – A
Trunk lid panel assembly
Side outer panel Trunk lid panel
assembly
Side outer panel

FRONT BUMPER ASSEMBLY
EXTERIOR51-2
FRONT BUMPER ASSEMBLY
ADHESIVEM1511000500426
FRONT BUMPER ASSEMBLY
REMOVAL AND INSTALLATIONM1511001400444
Item Specification
Front three-diamond mark Double-sided tape:
20 mm width and 0.8 mm thickness
AC304651AB
32
3
5
2
2 45
5
31
3
C
C
B
BA
A
A A A
A
AA
Claw
Clip Section A – A Section B – B Section C – C

FRONT BUMPER ASSEMBLY
EXTERIOR51-3
DISASSEMBLY AND REASSEMBLYM1511001600460
Removal steps
1. Splash shield mounting clip
2. Radiator grill assembly
3. Front bumper assembly•Fog lamp connector connection
4. Front bumper beam assembly
5. Front bumper fixing clip Removal steps (Continued)
AC304652AC
Double-sided tape: Generic products
[ 20 mm width and 0.8 mm thickness ]
1
1
8
7
9
6
6
5
5
3
4
34
N
N
2
Removal steps
1. Front three-diamond mark
2. Under duct
3. Air intake bezel <Vehicle without fog
lamp>
4. Fog lamp bezel <Vehicle with fog
lamp><<A>> >>A<<5. Front bumper rivet
6. Front bumper side plate
7. Front bumper centre cover
8. Licence plate garnish
9. Front bumper face Removal steps (Continued)