heater MITSUBISHI LANCER 2005 Manual PDF

Page 542 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-58
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
STEP 4. Resistance measurement at the C-139
A/C-ECU connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Measure the resistance between terminal 3 and
body earth.
OK: 2 ohms or less
Q: Is the check result normal?
YES :
Replace the manual air conditioner control
panel (A/C-ECU).
NO : Go to Step 5.
STEP 5. Check the wiring harness between C-139
A/C-ECU connector terminal No.3 and the earth.
•Check the A/C-ECU earth line for open circuit.
Q: Is the check result normal?
YES :
Replace the manual air conditioner control
panel (A/C-ECU).
NO : Repair the wiring harness.AC303818
Connector: C-139
<R.H.D.>
AJ
Harness side
C-139 (B)
11 12657 8 9 103 421
AC301541ET
Connector C-139
(Harness side)
11 12657 8 9 103 421
AC303818
Connector: C-139
<R.H.D.>
AJ
Harness side
C-139 (B)
11 12657 8 9 103 421

Page 543 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-59
INSPECTION PROCEDURE 11: A/C Compressor power supply system.
A/C
COMPRESSOR
RELAY
A/C
COMPRESSOR
A/C
REFRIGERANT
TEMPERATURE
SWITCH
MAGNETIC
CLUTCH
IGNITION
SWITCH (IG2)
ENGINE-ECU BATTERY
RELAY
BOX
ENGINE-A/T-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
: M/T
: A/TNOTE
A/C Compressor Circuit

Page 544 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-60
COMMENTS ON TROUBLE SYMPTOM
If the power is not supplied to the A/C compressor,
the A/C compressor circuit system may be
defective..
TROUBLESHOOTING HINTS
•Malfunction of the A/C compressor relay
•Damaged the wiring harness or connectors
DIAGNOSIS
STEP 1. Connector check: B-17X A/C
compressor relay connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO : Repair the connector.
STEP 2. Check the A/C compressor relay
continuity.
Refer to P.55-75.
Q: Is the A/C compressor relay in good condition?
YES :
Go to Step 3.
NO : Replace the A/C compressor relay.
STEP 3. Voltage measurement at B-17X A/C
compressor relay connector.
(1) Remove the relay, and measure at the relay box
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 2 and
body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 6.
NO <L.H.D.> : Go to Step 4.
NO <R.H.D.> : Go to Step 5.
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC301541EU
Connector B-17X
(Relay box side)
Front of
vehicle1
3 2
4

Page 545 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-61
STEP 4. Check the wiring harness between B-17X
A/C compressor relay connector terminal No.2
and the ignition switch (IG2).
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-15, joint connector C-35,
junction block connectors C-209 and C-210, and
repair if necessary.
•Check the A/C compressor relay power supply
line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303800
Connector: C-15
<L.H.D.>
AE
C-15 (L)
AC303798
Connector: C-35
<L.H.D.>
AJ
2 1313 12 1421 105 4616 15 17789
19 18 2011
22
C-35 (L)
AC303809
Connectors: C-209, C-210
AF
C-209
C-210
Junction block (front view) <L.H.D.>
C-209
Harness side
1016
145
12134117 238 9
C-210
Harness side
4 65321

Page 546 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-62
STEP 5. Check the wiring harness between B-17X
A/C compressor relay connector terminal No.2
and the ignition switch (IG2).
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-135, joint connector C-35,
junction block connectors C-209 and C-210, and
repair if necessary.
•Check the A/C compressor relay power supply
line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303814
Connector: C-35
<R.H.D.>
AI
C-35(L)
AC303818
Connector: C-135
<RHD>
AH
C-135 (L)
AC303823
Connectors: C-209, C-210
AE
C-210
Junction block (front view) <R.H.D.>
C-209
C-209
Harness side
1016
145
12134117 238 9
C-210
Harness side
4 65321

Page 547 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-63
STEP 6. Voltage measurement at B-17X A/C
compressor relay connector.
(1) Remove the relay, and measure at the junction
block side.
(2) Measure the voltage between terminal 1 and
body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 8.
NO : Go to Step 7.
STEP 7. Check the wiring harness between B-17X
A/C compressor relay connector terminal No.1
and the battery.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector A-13 <L.H.D.> or C-111
<R.H.D.>, and repair if necessary.
•Check the A/C compressor relay power supply
line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC301541EV
Connector B-17X
(Relay box side)
Front of
vehicle1
3 2
4
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303857
Connector: A-13
<LHD>
AB
A-13 (B)
AC303816
Connector: C-111
<RHD>
AF
615
121179
810234

Page 548 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-64
STEP 8. Connector check: B-114 A/C compressor
connector
Q: Is the check result normal?
YES :
Go to Step 9.
NO : Repair the connector.
STEP 9. Check the wiring harness between B-17X
A/C compressor relay connector terminal No.4
and B-114 A/C compressor connector terminal
No.1.
AC303782
Connector: B-114
<4G1-L.H.D.>
AC
Harness side
B-114 (B)
AC303790
Connector: B-114
<4G6-L.H.D.>
AC
Harness side
B-114 (B)
AC303786
Connector: B-114
<4G1-R.H.D.>
AB
Harness side
B-114 (B)
AC303794
Connector: B-114
<4G6-R.H.D.>
AB
Harness side
B-114 (B)
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303782
Connector: B-114
<4G1-L.H.D.>
AC
Harness side
B-114 (B)
AC303790
Connector: B-114
<4G6-L.H.D.>
AC
Harness side
B-114 (B)

Page 549 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-65
•Check the A/C compressor power supply line for
open circuit.
Q: Is the check result normal?
YES :
Go to Step 10.
NO : Repair the wiring harness.
STEP 10. Connector check: C-123 engine-ECU
connector <M/T> or C-122 engine-A/T-ECU
connector <A/T>
Q: Is the check result normal?
YES <M/T> :
Go to Step 11.
YES <A/T> : Go to Step 12.
NO : Repair the connector.
AC303786
Connector: B-114
<4G1-R.H.D.>
AB
Harness side
B-114 (B)
AC303794
Connector: B-114
<4G6-R.H.D.>
AB
Harness side
B-114 (B)
AC303805
Connectors: C-122 <A/T>, C-123 <M/T>
<L.H.D.>
C-122 (GR)
C-123 (Y)
C-122 Harness side
C-123
AE
AC303817
Connectors: C-122 <A/T>, C-123 <M/T>
AF
<R.H.D.>
C-122C-122 (GR)
C-123 (Y)
C-123 Harness side

Page 550 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-66
STEP 11. Check the wiring harness between
C-123 engine-ECU connector terminal No.8 and
B-17X A/C compressor relay connector terminal
No.3.
•Check the A/C compressor relay earth line for
open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
STEP 12. Check the wiring harness between
C-122 engine A/T-ECU connector terminal No.20
and B-17X A/C compressor relay connector
terminal No.3.
•Check the A/C compressor relay earth line for
open or short circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction P.00-5).
NO : Repair the wiring harness.
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303804
Connector: C-123
<LHD - M/T>
AH
Harness side
C-123 (Y)
AC303816
Connector: C-123
AM
<RHD - M/T>
Harness side
C-123 (Y)
AC304988AB
Connector: B-17X
Front of
vehicle
1
3 2
4
Relay box side
AC303804
Connector: C-122
<LHD - A/T>
AG
Harness side
C-122 (GR)
AC303816
Connector: C-122
AL
<RHD - A/T>
Harness side
C-122 (GR)

Page 551 of 788

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-67
CHECK AT ECU TERMINAL <L.H.D.>M1552010300527
12
345
678
9 10111213141516
AC300861AC
<C-139>
Terminal No. Check item Checking requirement Normal condition
1 Rear defogger switch Defogger switch: ON 0 V
Defogger switch: OFF System voltage
2 Inside/outside air selection
damper motor (outside air)When the damper is moved to
the inside air recirculation
position0 V
When the damper is moved to
the outside air inside air intake
positionSystem voltage
3 Inside/outside air selection
damper motor (inside air)When the damper is moved to
the inside air recirculation
positionSystem voltage
When the damper is moved to
the outside air inside air intake
position0 V
4 Output to the engine-A/T-ECU
(A/C1)A/C stopped 0 V
•A/C switch: ON
•Blower switch: ONSystem voltage
5 Output to the engine-A/T-ECU
(A/C2)When the A/C is under low load System voltage
When the A/C is under high
load0 V
6 Power supply to the A/C
illuminationLighting switch: ON System voltage
7---
8 Blower switch (lo) blower switch: lo System voltage
9---
10 Power supply to the ignition
switch (IG2)Ignition switch: ON System voltage
11 Earth to the A/C illumination Always 0 V
12 Earth Always 0 V
13 Air thermo sensor (outlet side) Sensor probe temperature 25°C
(1.5k ohm)2.2 V
14, 15 - - -
16 Earth to the air thermo sensor Always 0 V

Page:   < prev 1-10 ... 31-40 41-50 51-60 61-70 71-80 81-90 91-100 101-110 111-120 ... 150 next >