interior MITSUBISHI LANCER EVOLUTION X 2008 Owner's Guide

INSIDE REAR VIEW MIRROR
TSB Revision
INTERIOR52A-17
INSIDE REAR VIEW MIRRORM1521002600561
REMOVAL SERVICE POINT
1. Disengage claw A and lower the cover in the arrow 1 direction.
2. Push claw B in the arrow 2 direction to unlock, and pull out the mirror in the arrow 3 direction.
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001301165
WARNING
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions P.52B-24
and Air Bag Module and Clock Spring P.52B-367.
AC209066
Claw B
Claw A
Cover
12
3
AD
AC609288AB
4
3 1
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb 43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
1
4
2
2
2
3
2

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-18
REMOVAL SERVICE POINT
.
<<A>> WIRING HARNESS CONNECTOR DISCON-
NECTION
Disconnect the following wiring harness connectors:
INSTALLATION SERVICE POINT
.
>>A<< FRONT SEAT ASSEMBLY INSTALLATION
1.Temporarily tighten the bolts in all mounting locations
shown in the illustration with no load applied to the front
seat cushion and check the operation of the seat slide.
2. Tighten the bolts in all mounti ng locations to the specified
torque.
1.Head restraint
Front seat assembly removal
steps

2.Front seat anchor cover rear
3.Front seat anchor cover front
<<A>>•Harness connector
>>A<<4.Front seat assembly
Front seat assembly removal steps
(Continued)
Connector
numberConnector name
D-27 (4 −
black)Heated seat connector (driver's
seat) <Vehicle with heated seat>
D-28 (2 −
gray)Seat slide sensor connector
(driver's seat)
D-29 (4 −
black)Seat belt switch connector (driver's
seat)
D-30 (2 −
yellow)Side air bag module (squib)
connector (driver's seat) <Vehicles
with side air bag>
D-32 (2 −
yellow)Side air bag module (squib)
connector (front passenger's seat)
<Vehicles with side air bag>
D-33 (4 −
black)Seat belt switch connector (front
passenger's seat)
D-34 (4 −
black)Heated seat connector
(passenger's seat) <Vehicle with
heated seat>
D-35 (6)Occupant classification system
connector (passenger's seat)
AC611243
D-30 D-29
D-28D-27
AB
D-32
D-33
D-34 D-35
AC610011AB

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-19
INSPECTIONM1522005500287
CONTINUITY TEST OF HEATED SEAT SWITCH
.1. Check for continuity between terminals.
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is
supplied to terminal s 2 and terminal 6.
.
SEAT CUSHION HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Between terminals 1 and terminal 2
Standard type: Approximately 3.82 ± 4.66 ohms
Spots type: Approximately 4.47 ± 5.48 ohms
Between terminals 1 and terminal 4
Standard type: 8.90 ± 10.88 ohms
Spots type: 8.79 ± 10.75 ohms
.
ItemSwitch
positionTester
connectionSpecified
condition
Driver's
seat sideHI1 − 5, 3 − 8Continuity
exists (2
Ω
or less)
OFF1 − 5, 3 − 5, 5
− 8
Open
circuit
LO3 − 5Continuity
exists (2
Ω
or less)
Front
passenger'
s seat sideHI4 − 5, 8 − 9Continuity
exists (2
Ω
or less)
OFF4 − 5, 5 − 8, 5
− 9
Open
circuit
LO5 − 9Continuity
exists (2
Ω
or less)
ACX00625
AC610374

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-20
SEATBACK HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Standard type: 4.86 ± 5.94 ohms
Spots type: 4.06 ± 4.96 ohms
HEATED SEAT RELAY CONTINUITY CHECK
12
AC200100
Battery voltageTester
connectionSpecified
condition
Not applied3 − 4Open circuit
•Connect
terminal 1 to
the positive
battery
terminal
•Connect
terminal 2 to
the negative
battery
terminal
3 − 4Continuity
exists (2
Ω or
less)
AC610364
2
3
4
1
AB
Heated seat
relay

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-21
DISASSEMBLY AND ASSEMBLYM1522001501211
Required Special Tool:
•MB990784: Ornament Remover
AC506551
AC609289AB
1
2
3
4
5
9
10
67
12
11
23 14
13
N
10
20
19N
22
21
15
8
161718
41 ± 10 N·m
30 ± 8 ft-lb41 ± 10 N·m
30 ± 8 ft-lb
Disassembly steps
<<A>>1.Height adjuster lever cap
2.Height adjuster lever
3.Reclining adjuster cap
4.Reclining adjuster lever
5.Side shield cover
6.Inner seat belt
7.Hinge cover
8.Side shield inner cover
9.Reclining adjust er upper cover
10.Reclining adjuster cover
11 .Harness
12.Hook
13.Front seatback pad and frame
assembly
<<B>>14.Head restraint guide
15.Hog ling
16.Front seatback cover
17.Front seatback pad
18.Front seatback frame
19.Front seat cushion assembly
20.Hog ling
21.Front seat cushion cover
22.Front seat cushion pad
23.Front seat cushion frame
Disassembly steps (Continued)

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-22
REMOVAL SERVICE POINT
.
<<A>> HEIGHT ADJUSTER CAP REMOVAL
Use special tool MB990784 as shown to remove the height
adjuster lever cover.
.
<<B>> HEAD RESTRAINT GUIDE REMOVAL
AC609290
MB990784
AB
Height adjuster
lever cover
ACX01300AB

REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-23
REAR SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001800639
AC611154AB
43 ± 8 N·m
32 ± 6 ft-lb
1
23
4
43 ± 8 N·m
32 ± 6 ft-lb
<Bench seat>
5
Removal steps
1.Rear seat head restraint
>>C<<2.Rear seat cushion assembly
>>A<<3.Rear seatback assembly
4.Rear seat hook
5.Luggage room partition board
Removal steps (Continued)

REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-24
AC609245AB
11
410
10
5
3
9
8
2
6
7
21 ± 4 N·m
15 ± 3 ft-lb
21 ± 4 N·m
15 ± 3 ft-lb
38 ± 13 N·m
28 ± 10 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb 43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
<Sprit seat>
Removal steps
1.Rear seat head restraint
>>C<<2.Rear seat cushion assembly
3.Rear seat hook
>>B<<4.Rear seatback side assembly (RH)
>>B<<5.Rear seatback side assembly (LH)
>>A<<6.Rear seatback assembly (RH)
>>A<<7.Rear seatback assembly (LH)
8.Spacer
9.Snap ring
10.Rear seat armrest
11 .Rear seat striker
Removal steps (Continued)

REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-25
INSTALLATION SERVICE POINTS
.
>>A<< INSTALLATION OF REAR SEATBACK
ASSEMBLY (LH)/REAR SEATBACK ASSEMBLY
(RH)
Place the center hinge bracket of the rear seatback assembly
(LH) on top of the center hinge bracket of the rear seatback
assembly (RH) for installation.
.
>>B<< INSTALLATION OF REAR SEATBACK SIDE
ASSEMBLY (LH)/RE AR SEATBACK SIDE
ASSEMBLY (RH)
Press the rear seatback side as sembly in the direction shown
in the illustration and fit the attachment wire into the hook
securely to install the rear seatback side assembly.
.
>>C<< INSTALLATION OF REAR SEAT CUSHION
ASSEMBLY
Fit the rear seat cushion into the rear seat hook securely.
AC609262
Center hinge
bracket of rear
seatback assembly
(RH)
Center hinge
bracket of rear
seatback assembly
(LH)
AB
AC609261
AB
Hook
Rear seatback
side assembly
Attachment
wire
AC609260AB
Rear seat
hook
Rear seat
cushion
assembly

REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-26
DISASSEMBLY AND ASSEMBLYM1522002000766
AC609246AB
5
5
5
1
4
3
2
6
7
N
N
Disassembly steps
1.Hog ring
2.Rear seat cushion cover
3.Rear seat cushion pad
4.Hog ring
5.Rear seat head restraint guide
6.Rear seatback cover
7.Rear seatback pad
Disassembly steps (Continued)