interior MITSUBISHI LANCER EVOLUTION X 2008 Service Manual

REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-27
AC609247AB
10
17
218
19
1N
3
4
13
2524
14
12
11
23
15
6
7
8
9
5
10
22
16
20
21262728
N
N
N
N
N
N
N
N
22 ± 4 N·m
16 ± 3 ft-lb
22 ± 4 N·m
16 ± 3 ft-lb
22 ± 4 N·m
16 ± 3 ft-lb
Disassembly steps
1.Hog ring
2.Rear seat cushion cover
3.Rear seat cushion pad
4.Hog ring
5.Rear seatback side cover (LH)
6.Rear seatback side pad (LH)
7.Rear seatback armrest board
8.Rear seat folding knob garnish
9.Rear seat folding knob
10.Rear seat head restraint guide
11 .Hog ring
12.Center hinge bracket (LH)
13.Side hinge bracket (LH)
14.Rear seatback cover (LH)
15.Rear seatback pad (LH)
16.Rear seatback frame (LH)
17.Hog ring
18.Rear seatback side cover (RH)
19.Rear seatback side pad (RH)
20.Rear seat folding knob garnish
21.Rear seat folding knob
22.Rear seat head restraint guide
23.Hog ring
24.Side hinge bracket (RH)
25.Center hinge bracket (RH)
26.Rear seatback cover (RH)
27.Rear seatback pad (RH)
28.Rear seatback frame (RH)
Disassembly steps (Continued)

FRONT SEAT BELT
TSB Revision
INTERIOR52A-28
FRONT SEAT BELT
REMOVAL AND INSTALLATIONM1523001300972
CAUTION
SRS: Before removing and installing the seat belts with pre-tensioner, refer to GROUP 52B − SRS Ser-
vice Precautions P.52B-24 and Seat Belt with Pre-tensioner P.52B-393.
Required Special Tool:
•MB990784: Ornament Remover
Pre-removal and Post-installation Operation
•Turn the ignition key to the LOOK (OFF) position.
•Disconnect the negative battery terminal.
AC608130
AC610305
AC608130
1
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
AB
3
24
5
43 ± 8 N·m
32 ± 6 ft-lb
5 ± 1 N·m
44 ± 9 in-lb
43 ± 8 N·m
32 ± 6 ft-lb
6
Outer seat belt removal steps
<>1.Center pillar trim cup
•Lower center pillar trim (Refer to
P.52A-10).
2.Upper center pillar trim (Refer to
P.52A-10).
3.Outer seat belt (Refer to GROUP
52B, Seat Belt with Pre-tensioner
P.52B-389).
4.Adjustable seat belt anchor
Inner seat belt removal steps
5.Harness connector
•Shield cover (Refer to P.52A-21).
6.Inner seat belt

FRONT SEAT BELT
TSB Revision
INTERIOR52A-29
REMOVAL SERVICE POINT
.
<> UPPER CENTER PILLAR TRIM CAP
REMOVAL
Remove the opening trim. Remove the upper center pillar trim
cap by inserting the special tool MB990784 between the upper
center pillar trim and body as shown in the illustration.
INSPECTIONM1523004400451.
SEAT BELT BUCKLE SWITCH CONTINUITY
CHECK (DRIVER’S SIDE)
AC606516
A
A
MB990784
AIMB990784
Section A – A
Upper center
pillar trim cap
ItemTester
connectionSpecified
condition
Fastened seat
belt1 − 2Open circuit
Unfastened
seat belt1 − 2Continuity
exists (2
Ω or
less)
Fastened seat
belt3 − 4Open circuit
Unfastened
seat belt3 − 4Continuity
exists (2
Ω or
less)
AC610208

FRONT SEAT BELT
TSB Revision
INTERIOR52A-30
.
SEAT BELT BUCKLE SWITCH CONTINUITY
CHECK (PASSENGER’S SIDE)
ItemTester
connectionSpecified
condition
Fastened seat
belt1 − 2Open circuit
Unfastened
seat belt1 − 2Continuity
exists (2
Ω or
less)
AC610208

REAR SEAT BELT
TSB Revision
INTERIOR52A-31
REAR SEAT BELT
REMOVAL AND INSTALLATIONM1523001600810
AC609742
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
42
AB
3
1
51
43 ± 8 N·m
32 ± 6 ft-lb 43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb43 ± 8 N·m
32 ± 6 ft-lb
Removal steps
•Rear seat cushion assembly (Refer to
P.52A-23).
•Rear seatback assembly (Refer to
P.52A-23).
•Rear shelf trim (Refer to P.52A-10).
1.Inner seat belt
2.Center seat belt, inner
3.Center seat belt, outer
4.Outer seat belt
5.Lower child anchor bracket
Removal steps (Continued)