light MITSUBISHI MIRAGE 2014 6.G Repair Manual

Features and controls
3-89
3
Each tire, including the spare (if provided), should be checked
monthly when cold and inflated to the inflation pressure rec-
ommended by the vehicle manufacturer on the vehicle placard
or tire inflation pressure label. (If your vehicle has tires of a
different size than the size indicated on the vehicle placard or
tire inflation pressure label, you should determine the proper
tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped
with a tire pressure monitoring system (TPMS) that illuminates
CAUTION
!
If the tire pressure monitoring system warning light
does not illuminate when the ignition switch is
turned to the “ON” position or the operation mode
is put in ON, it means that the tire pressure monitor-
ing system is not working properly. Have the system
inspected by an authorized Mitsubishi Motors
dealer.
In such situations, a malfunctioning of the system
may be preventing the monitoring of the tire pres-
sure. Avoid sudden braking, sharp turning and
high-speed driving.

If a malfunction is detected in the tire pressure mon-
itoring system, the tire pressure monitoring system
warning light will blink for approximately 1 minute
and then remain continuously illuminated. The
warning light will issue further warnings each time
the engine is restarted as long as the malfunction
exists.
Check to see whether the warning light goes off after
few minutes driving.
If it then goes off during driving, there is no prob-
lem.
However, if the warning light does not go off, or if it
blinks again when the engine is restarted, have the
vehicle inspected by an authorized Mitsubishi
Motors dealer.
In such situations, a malfunctioning of the system
may be preventing the monitoring of the tire pres-
sure. For safety reasons, when the warning light
appears while driving, avoid sudden braking, sharp
turning and high-speed driving.
CAUTION
!
BK0162600US.book 89 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-90 Features and controls
3
a low tire pressure telltale when one or more of your tires is
significantly under-inflated.
Accordingly, when the low tire pressure telltale illuminates,
you should stop and check your tires as soon as possible, and
inflate them to the proper pressure. Driving on a significantly
under-inflated tire causes the tire to overheat and can lead to
tire failure.
Under-inflation also reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for proper tire
maintenance, and it is the driver’s responsibility to maintain
correct tire pressure, even if under-inflation has not reached the
level to trigger illumination of the TPMS low tire pressure tell-
tale.
Your vehicle has also been equipped with a TPMS malfunction
indicator to indicate when the system is not operating properly.
The TPMS malfunction indicator is combined with the low tire
pressure telltale.
When the system detects a malfunction, the telltale will flash
for approximately one minute and then remain continuously
illuminated. This sequence will continue upon subsequent
vehicle start-ups as long as the malfunction exists.
When the malfunction indicator is illuminated, the system may
not be able to detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of reasons, includ-
ing the installation of replacement or alternate tires or wheels
on the vehicle that prevent the TPMS from functioning prop-
erly. Always check the TPMS malfunction telltale after replac-
ing one or more tires or wheels on your vehicle to ensure that
the replacement or alternate tires and wheels allow the TPMS
to continue to function properly.
If the warning light illuminates while driving
N00532800501
1. If the tire pressure monitoring system warning light illu-
minates, avoid hard braking, sharp steering maneuvers
and high speeds. You should stop and adjust the tires to
the proper inflation pressure as soon as possible. Adjust
the spare tire at the same time. Refer to “Tires” on page 7-
19.NOTE
When inspecting or adjusting the tire pressure, do not
apply excessive force to the valve stem to avoid breakage.

After inspecting or adjusting the tire pressure, always
reinstall the valve cap on the valve stem.
Without the valve cap, dirt or moisture could get into the
valve, resulting in damage to the tire inflation pressure
sensor.

Do not use metal valve caps, which may cause a metal
reaction, resulting in corrosion and damage of the tire
inflation pressure sensors.

Once adjustments have been made, the warning light will
go off after a few minutes of driving.
BK0162600US.book 90 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-91
3
2. If the tire pressure monitoring system warning light
remains illuminated after you have been driving for about
20 minutes after you adjust the tire inflation pressure, one
or more of the tires may have a puncture. Inspect the tire
and if it has a puncture, have it repaired by an authorized
Mitsubishi Motors dealer as soon as possible.
NOTE
To avoid the risk of damage to the tire inflation pressure
sensors, have any punctured tire repaired by an authorized
Mitsubishi Motors dealer. If the tire repair is not done by
an authorized Mitsubishi Motors dealer, damage to the tire
inflation pressure sensor is not covered by your warranty.

Do not use an aerosol puncture-repair spray on any tire.
Such a spray could damage the tire inflation pressure sen-
sors.
Have any puncture repaired by an authorized Mitsubishi
Motors dealer.

Using the tire repair kit may damage the tire inflation
pressure sensor. The vehicle must promptly be inspected
and repaired by an authorized Mitsubishi Motors dealer
after using the tire repair kit.
The tire pressure monitoring system may not work normally in
the following circumstances:

A wireless facility or device using the same frequency is
near the vehicle.

Snow or ice is stuck inside the fenders and/or on the
wheels.

The tire inflation pressure sensor’s battery is dead.

Wheels other than Mitsubishi Genuine wheels are being
used.

Wheels that are not fitted with tire inflation pressure sen-
sors are being used.

Wheels whose ID codes are not memorized by the vehicle
are used.

Compact spare tire (if so equipped) is fitted on a road
wheel.

A window tint that affects the radio wave signals is
installed.
WA R N I N G
!
If the warning light illuminates while you are driv-
ing, avoid hard braking, sharp steering maneuvers
and high speeds.
Driving with an under-inflated tire adversely affects
vehicle performance and can result in an accident.
CAUTION
!
The warning light may not illuminate immediately
in the event of a tire blowout or rapid leak.
BK0162600US.book 91 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-92 Features and controls
3
NOTE
Tire inflation pressures vary with the ambient tempera-
ture. If the vehicle is subjected to large variations in ambi-
ent temperature, the tire inflation pressures may be under-
inflated (causing the warning light come on) when the
ambient temperature is relatively low. If the warning light
comes on, adjust the tire inflation pressure.Whenever the tires and wheels are replaced with
new ones
N00532900153
If new wheels with new tire inflation pressure sensors are
installed, their ID codes must be programmed into the tire pres-
sure monitoring system. Have tire and wheel replacement per-
formed by an authorized Mitsubishi Motors dealer to avoid the
risk of damaging the tire inflation pressure sensors. If the
wheel replacement is not done by an authorized Mitsubishi
Motors dealer, it is not covered by your warranty.
General information
N00533000236
Your tire pressure monitoring system operates on a radio fre-
quency subject to Federal Communications Commission
(FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This device complies with
part 15 of FCC Rules and Industry Canada licence-exempt
RSS standard(s).
Operation is subject to the following two conditions.

This device may not cause harmful interference

This device must accept any interference received, includ-
ing interference that may cause undesired operation.
CAUTION
!
The use of non-genuine wheels will prevent the
proper fit of the tire inflation pressure sensors,
resulting air leakage or damage of the sensors.
WA R N I N G
!
Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0162600US.book 92 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-96 Features and controls
3
NOTE
Mirror image is displayed on the screen.

Monitor brightness is adjusted automatically by sensors.

It is possible to change the display language of the screen.
For details, please refer to the separated owner’s manual
for “Mitsubishi Multi Entertainment System”.

Under certain circumstances, it may become difficult to
see an image on the screen, even when the system is func-
tioning correctly.
• In a dark area, such as at night.
• When water drops or condensation are on the lens.
• When sun light or headlights shine directly into the lens.
Instrument cluster
N00519000391
1- Tachometer → P.3-98
2- Multi-information display → P. 3 - 9 8
3- Speedometer → P. 3 - 9 7
4- Multi-information display switch
BK0162600US.book 96 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-99
3
Information display
N00574800015
Each time you lightly press the multi-information display switch (A), the display switches in the following order.NOTE
When the ignition switch or the operation mode is in OFF, the driving range display and average fuel consumption display are
not displayed.

While driving, the service reminder is not displayed even if you operate the multi-information display switch.1- Odometer → P.3-100 5- Driving range display → P. 3 - 1 0 1
2-
Trip odometer → P.3-1006- Average fuel consumption display → P.3-102
3-
Trip odometer → P. 3 - 1 0 07- Service reminder (distance) → P.3-103
4- Instrument panel light dimmer control → P.3-100 8- Service reminder (month) → P.3-103
BK0162600US.book 99 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-100 Features and controls
3
Odometer
N00574900016
The odometer indicates the total distance the vehicle has trav-
eled.Trip odometer
N00575000014
The trip odometer indicates the distance traveled between two
points.To reset the trip odometerTo return the display to 0, hold down the multi-information dis-
play switch for about 1 second or more. Only the currently dis-
played value will be reset.
Example
If trip odometer is displayed, only trip odometer will
be reset.NOTE
Both trip odometers and can count up to 9999.9
miles/kilometers.
When a trip odometer goes past 9999.9 miles/kilometers,
it returns to 0.0 miles/kilometers.

When disconnecting the battery terminal, the memories of
trip odometer displays and are cleared, and their
displays return to “0.0 miles/kilometers”.
Instrument panel light dimmer control
N00575100015
Each time you press the multi-information display switch (2),
there is a sound and the brightness of the instrument panel
lights changes.
Usage examples for trip odometer , trip odometer
It is possible to measure two currently traveled distances,
from home using trip odometer and from a particular
point on the way using trip odometer .
1- Brightness level
2- Multi-information display switch
Bright Dim
BK0162600US.book 100 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-101
3
NOTE
You can adjust to 8 different levels for when the parking
lights or headlights are illuminated and 8 for when they
are not.
Each time you reduce two brightness levels, the segment
display of the brightness level decreases one by one.

If you press and hold the switch for longer than about 1
second, the brightness automatically scrolls through its
different levels, and stops scrolling when you release the
switch. Select your desired level of brightness.

The brightness level of the instruments is stored when the
ignition switch is turned to the “OFF” position or the
operation mode is put in OFF.
Driving range display
N00575200016
This displays the approximate driving range (how many more
miles or kilometers you can drive). When the driving range
falls below approximately 30 miles (50 km), “---” is displayed.NOTE
The driving range is determined based on the fuel con-
sumption data. This may vary depending on the driving
conditions and habits. Treat the distance displayed as just
a rough guideline.

When you refuel, the driving range display is updated.
However, if you only add a small amount of fuel, the cor-
rect value will not be displayed. Fill to a full tank when-
ever possible.

When your vehicle is stopped on an extremely steep hill,
the driving range value may, change. This is due to the
movement of fuel in the tank and does not indicate any
breakdown.

The display setting can be changed to the preferred units
(miles or km).
Refer to “Changing the function settings” on page 3-105.
BK0162600US.book 101 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-104 Features and controls
3
2. This informs you that a periodic inspection is due. Contact
an authorized Mitsubishi Motors dealer or a repair facility
of your choice to have the system checked.
3. After your vehicle is inspected at an authorized Mitsubishi
Motors dealer, it displays the time until the next periodic
inspection.To resetThe “---” display can be reset while the ignition switch or the
operation mode is in OFF.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the service reminder display.2. Press and hold the multi-information display switch for
about 1 second or more to make the spanner mark start
flashing. (If there is no operation for about 10 seconds
with flashing, the display will revert to its original indica-
tion.)
3. With this indicator flashing, if you lightly press the multi-
information meter switch, the display switches from “---”
to “cLEAr”. After that, the time until the next periodic
inspection is shown.BK0162600US.book 104 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-105
3
NOTE
The “---” display cannot be reset while the ignition switch
or the operation mode is in ON.

When “---” is displayed, after a certain distance and a cer-
tain period of time, the display is reset and the time until
the next periodic inspection is displayed.

If you accidentally reset the display, consult an authorized
Mitsubishi Motors dealer for assistance.
Changing the function settings
N00556800143
When the ignition switch or the operation mode is in ON, the
fuel consumption unit, displayed in the multi-information dis-
play, and the average fuel consumption reset mode can be mod-
ified as desired.Changing the reset mode for average fuel consumption
N00575500019
You can change the mode condition for the average fuel con-
sumption display to “Auto reset” or “Manual reset”.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the driving range display.
Refer to “Information display” on page 3-99.
CAUTION
!
The customer is responsible for making sure that
regular inspections and maintenance and periodic
inspections and maintenance are performed.
Inspections and maintenance must be performed to
prevent accidents and malfunctions.
CAUTION
!
The driver should not operate the display while the
vehicle is in motion.
When operating the system, stop the vehicle in a safe
area.
BK0162600US.book 105 ページ ２０１３年３月２２日　金曜日　午後２時４１分