belt MITSUBISHI MONTERO 1991 Repair Manual
Page 635 of 1333
IN TE R FE R EN CE V ER IF IC ATIO N C HEC K F O R O HC E N G IN E
1991 Mitsubishi Montero
Maintenance & Service Information
1983-96 Mitsubishi - Timing Belt Information
Cordia, Diamante, Eclipse, Expo, Expo LRV, Galant, Mirage,
Montero, Pickup, Precis, Sigma, Tredia, Van, 3000GT
TIMING BELT INTERFERENCE VERIFICATION INFORMATION
TIMING BELT INTERFERENCE CAUTION
NOTE: CAMSHAFT DRIVE BELTS OR TIMING BELTS - The condition of
camshaft drive belts should always be checked on vehicles
which have more than 50,000 miles. Although some
manufacturers do not recommend replacement at a specified
mileage, others require it at 60,000-100,000 miles. A
camshaft drive belt failure may cause extensive damage to
internal engine components on most engines, although some
designs do not allow piston-to-valve contact. These designs
are often called "Free Wheeling". Many manufacturers changed
their maintenance and warranty schedules in the mid-1980's to
reflect timing belt inspection and/or replacement at
50,000-60,000 miles. Most service interval schedules shown in
this section reflect these changes. Belts or components
should be inspected and replaced if any of the following
conditions exist:
* Crack Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
TIMING BELT INTERFERENCE CHECK MENU
TIMING BELT INTERFERENCE VERIFICATION TABLE ( 1) \
\
\
\
\
\
Replacement Interval
Application Engine (Miles)
Passenger Cars
Cordia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
Diamante
1992-96 ...... ( 2) 3.0L V6 (DOHC) ............. 60,000
3.0L V6 (SOHC) ........... ( 4) 60,000
Eclipse
1990-94 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
1990-95 ....... ( 2) 2.0L 4-Cyl. ........... ( 4) 60,000
1990-94 ... ( 2) 2.0L 4-Cyl. Non-Turbo ..... ( 4) 60,000
1990-96 ..... ( 2) 2.0L 4-Cyl. Turbo ....... ( 4) 60,000
1996 ........... ( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo
1992-95 .......... 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo LRV
1995 ............. 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Galant
Page 636 of 1333
1985-87 ........ (2) 2.4L 4-Cyl. .......... ( 4) 60,000
1988 ............... 3.0L V6 .............. ( 3) 60,000
1989-93 .... ( 2) 2.0L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.0L 4-Cyl. (SOHC) ........ ( 4) 60,000
1994-96 .... ( 2) 2.4L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.4L 4-Cyl. (SOHC) ........ ( 4) 60,000
Mirage
1985-96 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
1985-88 ..... ( 2) 1.6L 4-Cyl. Turbo ........... 60,000
1989, 1991 ..... ( 2) 1.6L 4-Cyl. .............. 60,000
1993-96 ........... 1.8L 4-Cyl ................ 60,000
Precis
1987-93 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
Sigma
1989-90 ............ 3.0L V6 .............. ( 3) 60,000
Tredia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
3000GT
1991-96 .......... ( 2) 3.0L V6 ................ 60,000
Light Trucks
Montero
1985-96 ............ 3.0L V6 .............. ( 3) 60,000
1994-96 ............ 3.5L V6 .............. ( 3) 60,000
Pickup
1983-89 ........... 2.0L 4-Cyl. ........... ( 3) 60,000
1983-86 ... ( 2) 2.3L 4-Cyl. Turbo Diesel .. ( 4) 60,000
1990-96 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
3.0L V6 .............. ( 3) 60,000
Van
1987-90 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
( 1) - Other interference engine applications may exist which
are not indicated here.
( 2) - Interference engine. Check for possible damage to
piston(s) or valve(s) if there has been a timing belt
failure.
( 3) - Although the vehicle manufacturer does not recommend a
specific scheduled maintenance interval, aftermarket
belt manufacturers suggest the belt be replaced at
60,000 mile intervals.
( 4) - Vehicle manufacturer recommends replacing all belts at
the same time.
\
\
\
\
\
\
Page 662 of 1333
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
CAMSHAFT TIMING BELT
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1983-86 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 668 of 1333
1994-96 (3.0L DOHC & 3.5L) .................. 9.0 Qts. (8.5L)
Cooling System
1983-88 ..................................... 8.5 Qts. (8.0L)
1989-96
2.6L ....................................... 9.7 Qts. (9.2L)
3.0L ...................................... 10.0 Qts. (9.5L)
3.5L ...................................... 10.0 Qts. (9.5L)
Differential
1983-88 ..................................... 1.9 Qts. (1.8L)
1989-93
2.6L ....................................... 1.9 Qts. (1.8L)
3.0L ....................................... 2.7 Qts. (2.6L)
1994-96
3.0L & 3.5L ................................ 2.7 Qts. (2.6L)
Engine Oil
1983-86 ..................................... 6.0 Qts. (5.8L)
1987 ........................................ 5.2 Qts. (5.0L)
1988 ........................................ 5.0 Qts. (4.8L)
1989-91 ..................................... 5.5 Qts. (5.3L)
1992-96 ..................................... 5.2 Qts. (4.9L)
Power Steering ................................ 1.1 Qts. (1.0L)
Fuel Tank
1983-88 .................................... 15.9 Gals. (60L)
1989-90
2.6L 2-Door ............................... 15.9 Gals. (60L)
3.0L 2-Door ............................... 19.9 Gals. (75L)
2.6L & 3.0L 4-Door .......................... 24 Gals. (92L)
1991-96 ...................................... 24 Gals. (92L)
Manual Transmission
1983-91 ..................................... 2.3 Qts. (2.2L)
1992 ........................................ 2.4 Qts. (2.3L)
1993-96 ..................................... 2.6 Qts. (2.5L)
Transfer Case
1983-91 ..................................... 2.3 Qts. (2.2L)
1992-96 ..................................... 2.4 Qts. (2.3L)
(1) - Use of R12 in a R134a system will result in SEVERE DAMAGE.
( 2) - 1983 model equipped with manual transmission only.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
1983-86
15 x 6JJ (Steel) .............................. 215 SR15
1987-88
Page 692 of 1333
Courtesy of Mitsubishi Motor Sales of America.
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect coolant hose and tubes. Remove nuts and bolts
securing exhaust manifold. Remove exhaust manifold and gaskets.
Disconnect oil return pipe. Remove turbocharger assembly.
Removal (Stealth & 3000GT Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove alternator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect oxygen sensor electrical
connector. Remove oil return pipe. Remove turbocharger support bracket
and remove turbocharger from exhaust manifold. See Fig. 10.
Fig. 10: Removing Front Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Removal (Stealth & 3000GT Rear)
1) Disconnect battery cables and remove battery. Drain engine
oil and coolant. Remove accelerator cable. Remove air hose, air pipe
and heat protectors. Disconnect clutch booster vacuum hose. Remove air
Page 701 of 1333
CAMSHAFT TIMING BELT REPLACEMENT INFORMATION
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SEVERE & NORMAL SERVICE DEFINITIONS
NOTE: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at mileage intervals based on vehicle
operation. Service schedules are based on the following primary
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
NOTE: The following services are to be performed on vehicles
subjected to severe service. See SEVERE & NORMAL SERVICE
DEFINITIONS. This service is to be performed in addition
to the normal services listed in the NORMAL MAINTENANCE
SERVICE SCHEDULES.
SEVERE SERVICE CONDITIONS/ACTIONS TABLE
\
\
\
\
\
\
\
Condition Action Item Perform Every (1)
Page 702 of 1333
\
\
\b\
\b\
\b\
\
\
Short Trips In Replace Engine Oil 3,000 Miles or 3 Months
Freezing
\
\b\
\b\
\
\
Temperatures Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Towing Or Replace Engine Oil 3,000 Miles or 3 Months
Commercial Use
\
\b\
\b\
\
\
Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Driving Off-Road Replace Engine Oil 3,000 Miles or 3 Months
Or In Salty Or
\
\b\
\b\
\
\
Sandy Areas Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
Page 703 of 1333
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Severe Dust Replace Engine Oil 3,000 Miles or 3 Months
Conditions
\
\b\
\b\
\
\
Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Hot Weather, Replace Engine Oil 3,000 Miles or 3 Months
Stop-And-Go
\
\b\
\b\
\
\
Driving Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Extensive Idling Replace Engine Oil 3,000 Miles or 3 Months
\
\b\
\b\
\
\
Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Page 707 of 1333
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Page 712 of 1333
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
60,000 MILE (96,000 KM) SERVICE
60,000 MILE (96,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter