sensor MITSUBISHI MONTERO 1998 Service Manual

[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998
Pages: 1501, PDF Size: 25.81 MB
Search: (keyless entry, tire type, torque, tire pressure, overheating, climate settings)

Page 661 of 1501

Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\

MOTOR MOUNTS
MOTOR MOUNT INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\

O-RINGS, GASKETS, SEALS AND SPRING LOCKS
O-RING, GASKET, SEAL AND SPRING LOCK INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Leaking ................. A ............ ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary.
\
\
\
\
\
\
\

O2 SENSORS
O2 SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure

Page 667 of 1501

Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification. Refer to OEM recommended service'
procedures.
\
\
\
\
\
\
\

POWER STEERING PRESSURE SENSORS
POWER STEERING PRESSURE SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 2) Require repair or
replacement.
Inoperative ............. B ........... ( 3) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Resistance out of
specification .......... B .. Require repair or replacement.
Restricted, affecting
performance ............ A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or

Page 673 of 1501

Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\

SENSORS AND ACTUATORS
NOTE: Conditions pertaining to the sensors and actuators listed
in this section may be found under the name of the sensor
or actuator.
SENSOR ABBREVIATION TABLE
\
\
\
\
\
\
\

Sensor Abbreviation
Accelerator Pedal Position Sensor ......................... APP
Air Conditioning Cycling Switch ............................ AC
Air Conditioning Pressure Sensor ........................... ..
Air Fuel Ratio Sensor ...................................... ..
Barometric Pressure Sensor ............................... BARO
Camshaft Position Sensor .................................. CMP
Clutch Pedal Position Switch .............................. CPP
Cooling Fan Motor Sensors and Switches ..................... ..
Crankshaft Position Sensor ................................ CKP
Electronic Transmission Feedback Devices ................... ..
Engine Coolant Temperature Sensor ......................... ECT
Evaporative Emission feedback devices ...................... ..
Exhaust Gas Recirculation feedback devices ................. ..
Fan Control Sensor ......................................... FC
Intake Air Temperature Sensor ............................. IAT
Knock Sensor ............................................... KS
Manifold Absolute Pressure Sensor ......................... MAP
Mass Air Flow Sensor ...................................... MAF
O2 Sensor ................................................. O2S
Park Neutral Position Switch .............................. PNP
Power Steering Pressure Sensor ............................ PSP
Thermal Vacuum Valve ...................................... TVV
Throttle Position Sensor ............................ TP Sensor
Throttle Position Switch ................................... ..
Transmission Range Switch ........................... TR Switch
Vehicle Speed Sensor ...................................... VSS
Volume Air Flow Sensor .................................... VAF
\
\
\
\
\
\
\

ACTUATOR ABBREVIATION TABLE\
\
\
\
\
\
\

Actuator Abbreviation
Air Injection Control Solenoid ............................. ..
Electronic Transmission control devices .................... ..
Evaporative Emission Canister ............................ EVAP
Purge Device ............................................... ..
Exhaust Gas Recirculation Device .......................... EGR
Fuel Injector .............................................. ..
Idle Air Control .......................................... IAC

Page 680 of 1501

Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A .. Require repair or replacement.
Disconnected ............ A .. Require repair or replacement.
Kinked .................. A .. Require repair or replacement.
Melted .................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Out of adjustment ....... B ........... (1) Require repair or
replacement.
Routed incorrectly ...... 2 ................. Suggest repair.
Seized .................. A .. Require repair or replacement.
( 1) - Follow OEM recommended adjustment procedures. Require
repair or replacement if out of specification.
\
\
\
\
\
\
\

THROTTLE POSITION SENSORS
THROTTLE POSITION SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 2) Require repair or
replacement.
Inoperative ............. B ........... ( 3) Require repair or
replacement. Further
inspection required.
Missing ................. C ............ Require replacement.
Resistance out of
specification .......... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A .. ( 1) Require repair or replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not

Page 687 of 1501

(2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\

VACUUM TUBES
See VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC) .
VEHICLE SPEED SENSORS
VEHICLE SPEED SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 2) Require repair or
replacement.
Inoperative ............. B ........... ( 3) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Resistance out of
specification .......... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.

Page 688 of 1501

Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\

VOLUME AIR FLOW SENSORS
VOLUME AIR FLOW SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 2) Require repair or
replacement.
Inoperative ............. B ........... ( 3) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Resistance out of
specification .......... B .. Require repair or replacement.
Restricted, affecting
performance ............ A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.

Page 706 of 1501

of publication.\
\
\
\
\
\

MFI CONTROL RELAY
MFI control relay switches power to vehicle sensors and
actuators including Volume Airflow (VAF) sensor, crankshaft position
sensor, idle speed control, injectors and fuel pump. When ignition
switch is turned to RUN position, PCM energizes coils controlling
injectors, VAF sensor and idle air control. When ignition switch is
turned to START position, PCM energizes coils (through park/neutral
position switch on A/T models) to supply power to fuel pump. Relay
failure will cause a no-start condition. For testing procedure, see I
- SYSTEM/COMPONENT TESTS article.
IGNITION CHECKS
* PLEASE READ THIS FIRST *
NOTE: Perform all circuit tests with a Digital Volt-Ohmmeter
(DVOM) with a minimum 10-megohm input impedance, unless
stated otherwise in test procedure.
SPARK
Check for spark at coil wire (if applicable) and at each
spark plug wire using a high output spark tester. Check spark plug
wire resistance on suspect wires. Wire resistance should not exceed
22,000 ohms for all models except Eclipse 2.0L non-turbo and Montero.
On Eclipse 2.0L non-turbo, resistance should not exceed 8000 ohms. On
Montero, resistance should not exceed 26,000 ohms.
CAMSHAFT POSITION (CMP) SENSOR
For CMP sensor testing procedure, see G - TESTS W/CODES
article.
CRANKSHAFT POSITION (CKP) SENSOR
For CKP sensor testing procedure, see G - TESTS W/CODES
article.
DISTRIBUTORLESS IGNITION SYSTEM (DIS - 4-CYLINDER)
Ignition Coil Resistance (Eclipse)
1) On Mirage 1.8L, see POWER TRANSISTOR (MIRAGE). On Eclipse\
2.0L non-turbo, go to step 3). On Eclipse 2.0L turbo and 2.4L,
disconnect ignition coil connector. Go to next step.
2) On Eclipse 2.0L turbo, use DVOM to measure primary coil
resistance between ignition coil connector terminals No. 2 and 3 (coil
for cylinders No. 1 and 4) and terminals No. 1 and 3 (coil for
cylinders No. 2 and 3). See Fig. 3. On Eclipse 2.4L, use DVOM to
measure primary coil resistance Between ignition coil terminals. Go to
step 4).
Fig. 2: Ignition Coil Connector Terminals (Eclipse 2.0L Non-Turbo)
Courtesy of Mitsubishi Motor Sales of America

Page 718 of 1501

G - TESTS W/CODES
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - Self-Diagnostics
Montero & 3000GT
INTRODUCTION
* PLEASE READ THIS FIRST *
NOTE: If no faults were found while performing basic diagnostic
procedures in F - BASIC TESTING article, proceed with
self-diagnostics in this article. If no Diagnostic Trouble
Codes (DTCs) or only pass codes are present after entering
self-diagnostics, proceed to H - TESTS W/O CODES article for
diagnosis by symptom (i.e., ROUGH IDLE, NO START, etc.).
SYSTEM DIAGNOSIS
NOTE: PCM diagnostic memory is retained by direct power supply
from battery. Memory is not erased by turning off ignition,
but it will be erased if battery or PCM is disconnected.
System diagnosis can be accomplished using a scan tool. See
ENTERING ON-BOARD DIAGNOSTICS . Powertrain Control Module (PCM)
monitors several different engine control system circuits. If an
abnormal input signal occurs, a Diagnostic Trouble Code (DTC) is
stored in PCM memory and assigned a DTC number. Each circuit has its
own DTC number and message. A specific DTC indicates a particular
system failure, but does not indicate that cause of failure is
necessarily within system.
A DTC does not condemn any specific component; it simply
points out a probable malfunctioning area. If a DTC is set, PCM will
turn on MIL. System failures encountered are identified as either hard
failures or intermittent failures as determined by PCM.
Hard Failures
Hard failures cause MIL to come on and remain on until
failure is repaired. If MIL comes on and remains on (MIL may flash)
during vehicle operation, cause of failure may be determined by using
appropriate DTC diagnostic procedure. See TROUBLE CODE DEFINITION. If
a sensor fails, PCM will use a substitute value in its calculations to
continue engine operation. In this condition (limp-in mode), vehicle
is functional, but loss of good driveability may result.
Intermittent Failures
Intermittent failures may cause MIL to flicker, or come on
and go out after intermittent DTC goes away. However, corresponding
DTC will be retained in PCM memory. If related DTC does not reoccur
within a certain time frame, related DTC will be erased from PCM
memory. Intermittent failures may be caused by a sensor, connector or
wiring problems. See INTERMITTENTS in H - TESTS W/O CODES article.
The PCM also records and stores engine operating conditions
when malfunction occurred. This information is referred to as freeze
frame data. If malfunction is an engine misfire, or fuel system rich
or fuel system lean condition, freeze frame data will be updated with
the most current information regarding these failures. Freeze frame
data recorded is:
* Fuel System Status

Page 719 of 1501

* Load Value (Displayed As Percent)
* Engine Coolant Temperature
* Short Term Fuel Trim (Displayed As Percent)
* Long Term Fuel Trim (Displayed As Percent)
* MAP Vacuum
* Engine RPM
* Vehicle Speed Sensor
* DTC During Data Recording
SELF-DIAGNOSTIC SYSTEM
SERVICE PRECAUTIONS
Before proceeding with diagnosis, following precautions must
be observed:
* Ensure vehicle has a fully charged battery and functional
charging system.
* Visually inspect connectors and circuit wiring being worked
on.
* DO NOT disconnect battery or PCM. This will erase any DTCs
stored in PCM.
* DO NOT cause short circuits when performing electrical tests.
This will set additional DTCs, making diagnosis of original
problem more difficult.
* DO NOT use a test light in place of a voltmeter.
* When checking for spark, ensure coil wire is NOT more than
1/4" from chassis ground. If coil wire is more than 1/4" from
chassis ground, damage to vehicle electronics and/or PCM may
result.
* DO NOT prolong testing of fuel injectors. Engine may
hydrostatically (liquid) lock.
* When a vehicle has multiple DTCs, always repair lowest number
DTC first.
VISUAL INSPECTION
Most driveability problems in the engine control system
result from faulty wiring, poor electrical connections or leaking air
and vacuum hose connections. To avoid unnecessary component testing,
perform a visual inspection before beginning self-diagnostic tests.
ENTERING ON-BOARD DIAGNOSTICS
NOTE: DO NOT skip any steps in self-diagnostic tests or incorrect
diagnosis may result. Ensure self-diagnostic test applies to
vehicle being tested.
DTCs may be retrieved by using a scan tool only. Proceed to
DTC retrieval method.
NOTE: Although other scan tools are available, Mitsubishi
recommends using Multi-Use Tester II (MUT II) scan tool.
Using Scan Tool
1) Refer to manufacturer's operation manual for instructions
in use of scan tool. Before entering on-board diagnostics, see
SERVICE PRECAUTIONS . Locate Data Link Connector (DLC) under instrument
panel, near steering column.
2) Turn ignition switch to OFF position. Connect scan tool to
DLC. Turn ignition switch to ON position. Read and record scan tool
self-diagnostic output. Proceed to TROUBLE CODE DEFINITION.

Page 720 of 1501

TROUBLE CODE DEFINITION
When DTC is obtained, refer to appropriate DTC test
procedure.
DIAGNOSTIC TROUBLE CODES (DTCS)
NOTE: DTCs can only be retrieved by using a scan tool. Listed DTCs
are retrieved using a generic scan tool. MUT II scan tool
can be used, but it may not read all DTCs. DTCS listed are
not used on all vehicles.
DTC P0100
Volume Airflow (VAF) circuit failure. Possible causes are:
connector or harness, or faulty VAF sensor.
DTC P0105
Barometric (BARO) pressure circuit failure. Possible causes
are: connector or harness, or faulty BARO pressure sensor.
DTC P0105
Manifold Absolute Pressure (MAP) circuit failure. Possible
causes are: connector or harness, or faulty MAP sensor.
DTC P0110
Intake Air Temperature (IAT) circuit failure. Possible causes\
are: connector or harness, or faulty VAF sensor.
DTC P0115
Engine Coolant Temperature (ECT) circuit failure. Possible
causes are: connector or harness, or faulty ECT sensor.
DTC P0120
Throttle Position (TP) circuit failure. Possible causes are:
connector or harness, or faulty TP sensor.
DTC P0125
Excessive time to enter closed loop fuel control. Possible
causes are: faulty front HO2S, HO2S connector or harness, or faulty
fuel injector.
DTC P0130
Front Heated Oxygen Sensor (HO2S) circuit failure. Possible
causes are: connector or harness, or faulty HO2S.
DTC P0135
Front Heated Oxygen Sensor (HO2S) heater circuit failure.
Possible causes are: connector or harness, or faulty HO2S.
DTC P0136
Rear Heated Oxygen Sensor (HO2S) circuit failure. Possible
causes are: connector or harness, or faulty HO2S.
DTC P0141
Rear Heated Oxygen Sensor (HO2S) heater circuit failure.
Possible causes are: connector or harness, or faulty HO2S.
DTC P0150
Heated Oxygen Sensor (HO2S) circuit failure (bank 2, sensor
1). Possible causes are: connector or harness, or HO2S.

Page:   < prev 1-10 ... 101-110 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 ... 260 next >
Search: (trunk release, fuel tank removal, catalytic converter, infotainment, mirror controls, radio antenna)