engine oil MITSUBISHI MONTERO 1998 User Guide
Page 97 of 1501
Removal & Installation
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove glove box with lower frame
attached. Loosen duct joint bolt to free duct joint. Disconnect A/C
switch harness. Disconnect evaporator drain hose.
2) Disconnect refrigerant lines at firewall side of engine
compartment. Remove evaporator top bolts in passenger compartment.
Remove evaporator assembly. To install, reverse removal procedure. See
Figs. 12 and 13. If replacing evaporator, add 1.4 ounces of
refrigerant oil to new evaporator.
Fig. 12: Removing Evaporator Assembly
Courtesy of Mitsubishi Motor Sales of America.
Page 99 of 1501
Removal & Installation
Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Disconnect refrigerant temperature
sensor wiring connector. Remove temperature sensor from compressor. To
install, reverse removal procedure. Use new "O" ring on temperature
sensor.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Application Ft. Lbs. (N.m)
A/C Compressor Bolt/Nut .................... 17-20 (23-27)
A/C Compressor Bracket Bolt/Nut .................. 37 (50)
A/C Compressor Clutch Coil Nut ................... 12 (16)
A/C Engine Coolant Temperature Switch ............ 26 (35)
INCH Lbs. (N.m)
Blower Motor Bolts/Nuts ........................... 44 (5)
Condenser Bolts/Nuts ............................ 106 (12)
Dual-Pressure Switch ............................. 89 (10)
Evaporator Assembly Bolts/Nuts .................... 44 (5)
Heater Assembly Bolts/Nuts ........................ 44 (5)
\
\
\
\
\
\
WIRING DIAGRAMS
Page 153 of 1501
this information to control solenoids on transmission valve body. TCM
controls transmission shifting and torque converter lock-up.
TCM contains a self-diagnostic system, which will store
Diagnostic Trouble Codes (DTC) if failure or problem exists in
electronic control system. DTC can be retrieved to determine problem
area. See SELF-DIAGNOSTIC SYSTEM. TCM is located under left side of
instrument panel, left of steering column. See Fig. 1.
TCM INPUT DEVICES
Brakelight Switch Signal
Brakelight switch delivers input signal to TCM, indicating
vehicle braking. Brakelight switch is located on brake pedal support.
Cruise Control Electronic Control Unit (ECU)
Cruise control ECU delivers an input signal to control
overdrive operation in accordance with vehicle speed when cruise
control is operating. When in overdrive with cruise control on, if
vehicle speed drops 2 MPH less than the set speed, overdrive is
released to prevent reduction in vehicle speed. Once vehicle speed is
more than the set speed, overdrive function is resumed. If coolant
temperature is low, transmission will not shift into overdrive. Cruise
control ECU is located below center A/C vent, behind temperature
control panel on Montero. On Montero Sport, cruise control ECU is
located behind driver's kick panel.
Engine Coolant Temperature Sensor (ECT) Signal
Engine coolant temperature sensor delivers input signal to
TCM, indicating engine coolant temperature. Coolant temperature sensor
is located on engine.
Input & Output Shaft Speed Sensors
Sensors are magnetic pick-ups that monitor input and output
shaft speeds. AC waveforms are input to TCM by sensors. Sensors are
located on front and rear side of transmission case.
OD Switch Signal
The OD switch provides an input signal to TCM to indicate
when overdrive is selected by operator. When OD switch is depressed to
ON position, transmission will shift into 4th gear when shift lever is
in "D" position, and OD OFF light on instrument panel will go off.
When OD switch is released to OFF position, transmission will shift
into 3rd gear, and OD OFF light on instrument panel will come on. The
OD switch is mounted on shift lever.
Oil Temperature Sensor Signal
Oil temperature sensor provides TCM with ATF temperature
values. TCM uses this information to control shift points for maximum
performance. If transmission oil temperature exceeds standard values,
instrument panel ATF - TEMP light will come on. Sensor is mounted to
cooler line at transmission.
Park/Neutral Position (PNP) Switch Signal
PNP switch delivers an input signal to TCM indicating shift
lever position. Switch is located on side of transmission.
Throttle Position (TP) Sensor Signal
TP sensor delivers closed throttle and variable throttle
position input signals to TCM. TP sensor is located on side of
throttle body.
4WD Low Range Detection Switch
4WD low range detection switch provides information to TCM
Page 160 of 1501
Once repairs have been performed, DTCs must be cleared from
TCM memory. DTCs may be cleared by disconnecting negative battery
cable for 10 seconds or more. Reconnect cable and ensure DTCs have
been cleared. Start engine and warm to normal operating temperature.
Run engine at idle for 10 minutes. DTCs may also be cleared using scan
tool. Refer to manufacturer's instruction manual.
DIAGNOSTIC TESTS
NOTE: For terminal and wire color identification, see WIRING
DIAGRAMS.
DTC 11: THROTTLE POSITION (TP) SENSOR
For diagnosis and testing information, see appropriate SELF-
DIAGNOSTICS article in ENGINE PERFORMANCE section. If TP sensor is
okay, check wiring harness and connectors between TP sensor and TCM.
Repair if necessary. If wiring harness and connectors are okay,
replace TCM.
DTC 15 & 16: OPEN OR SHORT IN OIL TEMPERATURE SENSOR CIRCUIT
1) Test oil temperature for proper operation. See OIL
TEMPERATURE SENSOR under COMPONENT TESTING. If oil temperature sensor
is okay, check wire harness, connectors and ground circuit for poor
connections or damage. Go to next step.
2) If wire harness and connectors are okay, check DTCs again
and verify code No. 15 or No. 16 still exists. If either code still
exists, replace TCM.
DTC 21 & 22: SHORT OR OPEN IN IGNITION SIGNAL CIRCUIT
1) Using an external tachometer, verify vehicles' tachometer
is operating accurately. If tachometer is incorrect, check ignition
coil and ignition power transistor and circuits for malfunction. See
appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section.
2) If tachometer is okay, check TCM wire harness connector
for poor connection. If wire harness is okay, recheck DTCs. If codes
reappear check wire harness between ignition power transistor and TCM.
If wire harness is okay, replace TCM.
DTC 23 & 24: OPEN OR SHORT IN SIGNAL LINE (ECT) FROM ECM TO
TCM
Check wire harness, connectors and ground circuit for poor
connections or damage. Go to next step. If wire harness and connectors
are okay, check DTCs again and verify code No. 23 or No. 24 still
exists. If either code still exists, replace TCM.
DTC 29 & 30: SHORT OR OPEN IN PARK/NEUTRAL POSITION (PNP)
SWITCH CIRCUIT
1) Check PNP switch for correct operation. See. If PNP switch
is okay, disconnect switch connector and measure voltage between
harness connector terminal No. 1 and ground.
2) If battery voltage does not exist, check wire harness and
connectors. See WIRING DIAGRAMS. If battery voltage exists, check wire
harness and connectors between PNP switch and TCM. If wire harness is
okay, replace TCM.
DTC 31: INPUT SPEED SENSOR
Page 164 of 1501
If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check overdrive brake for a
mechanical failure. See OVERDRIVE BRAKE in MITSUBISHI R4AW3 & V4AW3
OVERHAUL article.
SYMPTOM TROUBLE SHOOTING
NOTE: Check system using appropriate scan tool. See WIRING DIAGRAMS
for electrical schematics and COMPONENT TESTING.
COMMUNICATION WITH SCAN TOOL NOT POSSIBLE
If scan tool cannot communicate with TCM, check proper
connection with DLC. Check TCM power circuits, TCM ground circuits and
malfunctioning TCM.
SHIFT POINTS INCORRECT
If shift points are incorrect, check for DTCs. If no DTC is
present, check oil temperature sensor, pattern select switch, 4WD low
range detection switch and TCM for proper operation.
UPSHIFTS OCCUR SPONTANEOUSLY
If upshifting occurs spontaneously, check park/neutral
position switch, overdrive switch and TCM for proper operation.
TCC LOCK-UP MALFUNCTIONING
If TCC lock-up system is not operating properly, check torque
converter, valve body, lock-up switch and oil temperature switch.
COMPONENT TESTING
A/T FLUID TEMPERATURE SWITCH
1) Remove fluid temperature switch, located to rear of
neutral safety switch. Immerse switch in container of ATF up to top
threaded portion of switch. Using a DVOM, check continuity between
switch terminals. Continuity should not exist when fluid temperature
is 257
F (125C) or less.
2) When fluid is heated to 289-304F (143-151C), continuity
should exist. Replace switch if necessary. Apply thread sealant to
fluid temperature switch threads and install in transmission.
BRAKELIGHT SWITCH
1) Disconnect electrical connector from brakelight switch,
located near brake pedal. Using ohmmeter, ensure continuity exists
between terminal No. 2 (White/Red wire) and terminal No. 3 (Green
wire) with brake pedal released. Replace brakelight switch if
continuity does not exist. Continuity should not exist between
terminals No. 2 and No. 3 with brake pedal depressed.
2) If continuity does not exist, ensure brake pedal is
properly adjusted so brakelight switch has proper travel for switch
operation. If proper brakelight switch travel exists, replace
brakelight switch.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR
Page 169 of 1501
\b \
\
\
\
\
\
\
14 No. 1 Shift Solenoid In 1st Or 2nd Battery
\b
\
\
\
\
\
\
\
14 No. 1 Shift Solenoid In 3rd Or 4th Gear 0 Volts
\b
\
\
\
\
\
\
\
15 Power Supply Ignition ON Battery
\b
\
\
\
\
\
\
\
15 Power Supply Ignition OFF 0 Volts
\b
\
\
\
\
\
\
\
16 No. 2 Shift Solenoid In 2nd Or 3rd Gear Battery
\b
\
\
\
\
\
\
\
16 No. 2 Shift Solenoid In 1st Or 4th Gear 0 Volts
\b
\
\
\
\
\
\
\
17 Diagnostic Test Mode Not Specified Not Specified
\b
\
\
\
\
\
\
\
18 Diagnostic Output Scan Tool Not Battery
Connected
\b
\
\
\
\
\
\
\
21 Oil Temp Warning Lamp Normal Temp. Range 0 Volts
\b
\
\
\
\
\
\
\
21 Oil Temp Warning Lamp For 5 Seconds After Battery
Ign. Is On
\b
\
\
\
\
\
\
\
22 Oil Temp Sensor Temp @ 248F (120C) About 1.9
\b
\
\
\
\
\
\
\
22 Oil Temp Sensor Temp @ 302F (150C) About 1.1
\b
\
\
\
\
\
\
\
23 4WD Low Range Switch 4WD Lever In 4H-Lock Battery
\b
\
\
\
\
\
\
\
23 4WD Low Range Switch 4WD Lever In 4L-Lock 0 Volts
\b
\
\
\
\
\
\
\
24 Neutral Safety Switch In "R" Position Battery
\b
\
\
\
\
\
\
\
24 Neutral Safety Switch Except In "R" 0 Volts
\b
\
\
\
\
\
\
\
25 Ground Engine Idling 0 Volts
\b
\
\
\
\
\
\
\
26 Ground Engine Idling 0 Volts
\b
\
\
\
\
\
\
\
31 Neutral Safety Switch In "L" Position Battery
\b
\
\
\
\
\
\
\
31 Neutral Safety Switch Except In "L" 0 Volts
\b
\
\
\
\
\
\
\
32 Neutral Safety Switch In "N" Position Battery
\b
\
\
\
\
\
\
\
32 Neutral Safety Switch Except In "N" 0 Volts
\b
\
\
\
\
\
\
\
34 Power Mode Power Mode Selected Battery
\b
\
\
\
\
\
\
\
34 4WD Detection Switch 2WD 4 Volts Or
Montero Greater
\b
\
\
\
\
\
\
\
34 4WD Detection Switch 4WD 0-1 Volts
Montero
\b
\
\
\
\
\
\
\
34 Free Wheel 2WD 4 Volts Or
Montero Engage Switch Greater
Sport
\b
\
\
\
\
\
\
\
34 Free Wheel 4WD 0 Volts
Montero Engage Switch
Sport
\b
\
\
\
\
\
\
\
Page 252 of 1501
(VIN H) ........................................ 8.9:1
(VIN J) ....................................... 10.0:1
(VIN K) ........................................ 8.0:1
(VIN P) ........................................ 9.0:1
3.5L (VIN M & P) ................................. 9.0:1
Compression Pressure
1.5L (VIN A) ..................... 192 psi (13.4 kg/cm
)
1.8L (VIN C) ..................... 199 psi (13.9 kg/cm)
2.0L (VIN F) ..................... 178 psi (12.5 kg/cm)
2.0L (VIN Y) ............ 170-225 psi (11.7-15.5 kg/cm)
2.4L (VIN G) ..................... 192 psi (13.4 kg/cm)
3.0L
(VIN H & P) .................... 171 psi (12.0 kg/cm
)
(VIN J) ........................ 185 psi (13.0 kg/cm)
(VIN K) ........................ 156 psi (10.9 kg/cm)
3.5L (VIN M & P) ................. 171 psi (12.0 kg/cm)
Maximum Variation
Between Cylinders ( 2) ............... 14 psi (1.0 kg/cm
)
( 1) - See A - ENGINE/VIN ID article for VIN information.
( 2) - On Eclipse 2.0L non-turbo engine, maximum variation
between cylinders is 25 percent.
\
\
\
\
\
\
VALVE CLEARANCE
NOTE: All engines are equipped with hydraulic lifters. No
adjustment is required.
IGNITION SYSTEM
IGNITION COIL
IGNITION COIL RESISTANCE - Ohms @ 68F (20C) TABLE \
\
\
\
\
\
Application (1) Primary Secondary
1.5L (VIN A) ............ .5-.7 .......... 15,000-22,000
1.8L (VIN C) ............. ( 2) ........... 14,000-21,000
2.0L
(VIN F) .............. .70-.86 ......... 11,300-15,300
(VIN Y) .............. .51-.61 ......... 11,500-13,500
2.4L (VIN G)
Eclipse .............. .74-.90 ......... 20,100-27,300
Galant ............... .9-1.2 .......... 20,000-29,000
Montero Sport ........ .67-.81 ......... 11,300-15,300
3.0L
(VIN H) .............. .72-.88 ......... 10,300-13,900
(VIN J & K) .......... .67-.81 ......... 11,300-15,300
(VIN P) .............. .74-.90 ......... 20,100-27,300
3.5L
(VIN M) .............. .74-90 .......... 20,100-27,300
(VIN P) .............. .50-.70 ........... 9000-13,000
( 1) - See A - ENGINE/VIN ID article for VIN information.
( 2) - Information is not available from manufacturer at time
of publication.
\
\
\
\
\
\
HIGH TENSION WIRE RESISTANCE
Wire resistance should not exceed 22,000 ohms for all models
Page 260 of 1501
specified, bleed system and inspect hydraulic and clutch components.
See CLUTCH PEDAL SPECIFICATIONS table.
CLUTCH PEDAL INTERLOCK SWITCH
1) Place transmission in Neutral and apply parking brake.
Turn ignition switch to START position with clutch pedal not
depressed. Engine should not crank. If engine cranks, adjust or
replace interlock switch.
2) Disconnect interlock switch connector. Interlock switch
connector is located at clutch pedal. Depress and release interlock
switch. Using ohmmeter, check continuity between interlock switch
terminals. If continuity exists with interlock switch depressed and
does not exist with switch released, switch is okay. Adjust or replace
as necessary.
REMOVAL & INSTALLATION
CLUTCH ASSEMBLY
Removal (2WD Models)
1) Disconnect negative battery cable. Remove shift knob, dust
cover retaining plate, gaskets, stopper plate and control lever
assembly. Raise and support vehicle.
2) Remove front exhaust pipe. Drain transmission fluid. Index
mark drive shaft flange and remove drive shaft.
3) Disconnect back-up light switch connector, speedometer
cable connection and exhaust pipe mounting bracket. Remove lower
bellhousing cover. Disconnect clutch cable from clutch lever.
4) Support transmission with jack. Remove rear engine mount
nuts and bolts from transmission. Remove crossmember with rear engine
mount. Remove remaining bellhousing bolts, move transmission toward
rear and lower from vehicle.
5) If reusing pressure plate, index mark pressure plate to
flywheel for installation reference. Install a clutch alignment tool
to prevent pressure plate and clutch disc from dropping. Loosen
pressure plate bolts gradually in a crisscross pattern to avoid
warping pressure plate flange during removal. Remove pressure plate
and clutch disc. See Fig. 3.
Inspection
1) Check release bearing and release fork for damage or wear.
DO NOT clean release bearing assembly in solvent.
2) Inspect pressure plate surface for wear, cracks, and/or
discoloration. Measure diaphragm spring ends for wear and uneven
height. Replace assembly if height difference between fingers exceeds
.02" (.5 mm).
3) Check facing of clutch disc for loose rivets, uneven
contact, deterioration, seizure or oil saturation. Measure distance
from clutch disc surface to head of rivet. Replace clutch disc if
distance is less than .012" (.30 mm). Replace worn or defective
components as necessary. See Fig. 4.
CAUTION: Install clutch disc with manufacturer's stamp mark (located
near hub of clutch disc) toward pressure plate.
Installation
1) Using a clutch alignment tool, install pressure plate and
clutch disc. If reusing pressure plate, ensure index marks are
aligned. Tighten bolts evenly in a crisscross pattern to
specification. See TORQUE SPECIFICATIONS . See Fig. 3.
2) Clean release bearing sliding surface. DO NOT clean
Page 331 of 1501
D - ADJUSTMENTS
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - On-Vehicle Adjustments
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
ENGINE MECHANICAL
Before performing any on-vehicle adjustments to fuel or
ignition system, ensure engine mechanical condition is okay (i.e.,
engine compression).
VALVE CLEARANCE
VALVE ADJUSTMENT
NOTE: All models use hydraulic valve lifters. Adjustment is not
required.
CHECKING HYDRAULIC VALVE LIFTERS
1) Warm engine to normal operating temperature. Remove valve
cover. Position cylinder No. 1 at TDC on compression stroke. On 4-
cylinder engines, check intake rockers on cylinders No. 1 and 2. Check
exhaust rockers on cylinders No. 1 and 3. On V6 engines, check intake
rockers on cylinders No. 1, 5 and 6. Check exhaust rockers on
cylinders No. 1, 2 and 3.
2) Push downward on end of rocker arm, above lash adjuster.
Rotate crankshaft 360 degrees. On 4-cylinder engines, check intake
rockers on cylinders No. 3 and 4. Check exhaust rockers on cylinders
No. 2 and 4. On V6 engines, check intake rockers on cylinders No. 2, 3
and 4. Check exhaust rockers on cylinders No. 4, 5 and 6. If lash
adjuster is normal, it will feel solid.
3) If lash adjuster moves downward easily when pushed,
replace adjuster. If lash adjuster feels soft or spongy, air has
probably entered lash adjuster. If this occurs, check engine oil
level. If engine oil level is okay, check oil screen and oil screen
gasket for damage.
4) After repairing cause of air ingestion, warm engine to
operating temperature. Drive vehicle at low speed for approximately 5
minutes. Turn engine off for a few minutes.
5) Restart engine and drive at low speed for approximately 5
minutes. Repeat this step several times for about one hour. This helps
remove air from engine oil.
IGNITION TIMING
NOTE: Perform all checks with engine at normal operating
temperature, cooling fan and accessories off, transmission
in Park or Neutral, and front wheels in straight-ahead
position. Ignition timing check procedure for Eclipse 2.0L
non-turbo not available from manufacturer at time of
publication.
Diamante
1) Ignition timing is controlled by Powertrain Control Module
(PCM) and is not adjustable. Manufacturer provides procedure for
checking timing. DO NOT attempt to adjust ignition timing by rotating
Page 415 of 1501
FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES