ad blue MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 26 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION](/img/19/57333/w960_57333-25.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION")
\
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
B/P Backpressure
BAC By-Pass Air Control
BAP Barometric Absolute Pressure Sensor
BARO Barometric
BBDC Before Bottom Dead Center
BCM Body Control Module
BDC Bottom Dead Center
BHP Brake Horsepower
BLK Black
BLU Blue
BMAP Barometric & Manifold Absolute Pressure Sensor
BOO Brake On-Off Switch
BP Barometric Pressure sensor
BPS Barometric Pressure Sensor
BPT Backpressure Transducer
BRN Brown
BTDC Before Top Dead Center
BTU British Thermal Unit
BVSV Bimetallic Vacuum Switching Valve
Baro. Barometric
Batt. Battery
Bbl. Barrel (Example: 4-Bbl.)
Blst. Ballast
Blwr. Blower
Brkr. Breaker
\
\
\
\
\
\
\
\f
"C" ABBREVIATION TABLE
"C" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
C Celsius (Degrees)
C(3) I Computer Controlled Coil Ignition
C(4) Computer Controlled Catalytic Converter
CANP Canister Purge solenoid
CARB California Air Resources Board
CAT Catalytic Converter
CB Circuit Breaker
CBD Closed Bowl Distributor
CBVV Carburetor Bowl Vent Valve
cc Cubic Centimeter
CCC Computer Command Control
CCD Computer Controlled Dwell
CCM Central Control Module
CCO Converter Clutch Override
CCOT Cycling Clutch Orifice Tube
CCW Counterclockwise
CDI Capacitor Discharge Ignition
CEC Computerized Engine Control
CFI Central Fuel Injection
CID Cubic Inch Displacement
CID Cylinder Identification sensor
CIS Continuous Injection System
CIS-E Continuous Injection System-Electronic
CKT Circuit
CLR Clear
CNG Compressed Natural Gas
Page 27 of 1501
CO Carbon Monoxide
CO2 Carbon Dioxide
CONV Convertible
CP Canister Purge
CPA Connector Position Assurance
CPS Crank Position Sensor
CTS Coolant Temperature Sensor
CV Check Valve or Constant Velocity
CVC Constant Vacuum Control
CW Clockwise
CYL or Cyl. Cylinder
Calif. California
Carb. Carburetor
Chrg. Charging
Circ. Circuit
Cntrl. Control
Comp. Compressor or Compartment
Conn. Connector
Cont. Continued
Conv. Convertible or Converter
Cu. In. Cubic Inch
Cyl. Cylinder
\
\
\
\
\
\
\
\f
"D" ABBREVIATION TABLE
"D" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
"D" Drive
DBC Dual Bed Catalyst
DC Direct Current or Discharge
DDD Dual Diaphragm Distributor
DERM Diagnostic Energy Reserve Module
DFI Digital Fuel Injection
DIC Driver Information Center
DIS Direct Ignition System
DIS Distributorless Ignition System
DIST Distribution
DISTR Distributor
DK BLU Dark Blue
DK GRN Dark Green
DME Digital Motor Electronics (Motronic System)
DOHC Double Overhead Cam
DOT Department of Transportation
DP Dashpot
DRB-II Diagnostic Readout Box
DVOM Digital Volt/Ohm Meter (see VOM)
Def. Defogger or Defroster
Def. Defrost
Defog. Defogger
Diag. Diagnostic
Dist. Distributor or Distribution
Dr. Door
\
\
\
\
\
\
\
\f
"E" ABBREVIATION TABLE
"E" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
Page 30 of 1501
Ign. Ignition
In. Inches
Inj. Injector
\
\
\
\
\
\
\
\f
"J" ABBREVIATION TABLE
"J" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
J/B Junction Block
\
\
\
\
\
\
\
\f
"K" ABBREVIATION TABLE
"K" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
k/ohms 1000 ohms (kilo as in k/ohms)
kg Kilograms (weight)
kg/cm Kilograms Per Square Centimeter
KAM Keep Alive Memory
KAPWR Keep Alive Power
KM/H Kilometers Per Hour
KOEO Key On Engine Off
KOER Key On Engine Running
KS Knock Sensor
\
\
\
\
\
\
\
\f
"L" ABBREVIATION TABLE
"L" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
L Liter(s)
L/D Light Duty
LCD Liquid Crystal Display
LED Light Emitting Diode
LH Left Hand
LOS Limited Operation Strategy
LT BLU Light Blue
LT GRN Light Green
LUS Lock-Up Solenoid
Lbs. Pounds
Lt(s). Light(s)
Lugg. Luggage
\
\
\
\
\
\
\
\f
"M" ABBREVIATION TABLE
"M" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
mA Milliamps
mV Millivolts
mfd. Microfarads
Page 87 of 1501
settings.
2) Set blower/fan on high speed. Close doors and windows.
Insert thermometer in center vent. Operate system for 20 minutes to
allow system to stabilize. Measure temperature.
3) Discharge air temperature must be 37-44
F (3-7C) at
center vent, with high side and low side pressures within
specification. See A/C SYSTEM SPECIFICATIONS table at beginning of
article.
A/C CONTROL UNIT (ACCU)
1) Locate A/C Control Unit (ACCU) on top of evaporator case
and disconnect 10-pin connector. Inspect connector and wiring for
damage. Turn ignition and A/C on. Set temperature control to maximum
cooling and blower switch to high. Using a DVOM set to appropriate
test function, inspect harness side of connector. See Fig. 3. Go to
next step. If all test readings are as specified, replace ACCU.
2) Terminal No. 1 (Green/Yellow wire) is ACCU output. With
A/C and blower motor on, battery voltage should be present when ACCU
has received signals from pressure and temperature sensors confirming
A/C operation is okay.
3) Terminal No. 3 (Green/Blue wire) is ACCU power supply whe\
n
A/C switch is in A/C mode. With ignition and blower on, and A/C switch
at second level setting, battery voltage should be present.
4) Terminal No. 5 (Green/Red wire) is ACCU power supply when\
A/C switch is in ECONO mode. With ignition and blower on, and A/C
switch at first level setting, battery voltage should be present.
Terminals No. 2 and 7 (Black wire) are ACCU grounds. There should be
zero volts at all times.
5) Turn ignition off. Reconnect 10-pin connector. Turn
ignition on. Turn A/C on. Set temperature control to maximum cooling
and blower switch to high. Backprobe 10-pin connector. Go to next
step. If all test readings are as specified, replace ACCU.
6) Terminal No. 10 (Blue/White wire) is air thermosensor
power supply. With ignition, blower and A/C on, approximately 5.5
volts should be present.
7) Terminal No. 8 (Blue/Yellow wire) is air thermosensor
signal. When temperature of evaporator outlet portion is 77
F (25C),
there should be approximately 3.6 volts present.
8) Terminal No. 4 (White/Blue wire) is air inlet sensor powe\
r
supply. With ignition, blower and A/C on, approximately 5.5 volts
should be present.
9) Terminal No. 9 (Yellow/Green wire) is air inlet sensor
signal. When temperature of evaporator outlet portion is 77
F (25C),
there should be approximately 1.5 volts present.
Fig. 1: Testing ACCU
Courtesy of Mitsubishi Motor Sales of America.
A/C SWITCH
Page 102 of 1501
Transportation (DOT) approved, DOT 4BW or DOT 4BA refrigerant
containers.
7) Never overfill refrigerant containers. The safe filling
level of a refrigerant container MUST NOT exceed 60 percent of the
container's gross weight rating. Store refrigerant containers at
temperature less than 125
F (52C).
8) R-134a refrigerant is sold and stored in 30- or 50-pound
Light Blue containers, while Freon (R-12) is stored in White colored
containers.
9) Refrigerant R-12 and R-134a must never be mixed, as they
and their desiccants and lubricants are not compatible. If
refrigerants are mixed, system cross-contamination or A/C system
component failure may occur. Always use separate servicing and
refrigerant recovery/recycling equipment.
10) Follow equipment manufacturer instructions of all service
equipment to be used. The Material Safety Data Sheet (MSDS), provided
by refrigerant manufacturer/suppliers, contains valuable information
regarding the safe handling of refrigerants.
11) Before connecting refrigerant lines always lubricate "O"
rings using appropriate refrigerant oil.
12) Always plug or cap A/C system refrigerant lines and
component connections as soon as possible to protect components from
moisture and/or dust. DO NOT remove plugs or caps until ready to
install component.
13) Always use a back-up wrench when tightening or loosening
fittings.
IDENTIFYING R-134a SYSTEMS & COMPONENTS
To prevent refrigerant cross-contamination, use following
methods to identify R-134a based systems and components.
Fittings & "O" Rings
All R-134a based A/C systems use 1/2" - 16ACME threaded
fittings (identifiable by square threads) and quick-connect service
couplings. See Fig. 1. Besides the use of these fittings, most
manufacturers will use Green colored "O" rings in R-134a systems.
Fig. 1: Identifying R-134a Fittings & Quick-Connect Service Couplings
Courtesy of Audi of America, Inc.
Underhood A/C Specification Labels
Most R-134a based systems will be identified through the use
Page 104 of 1501
Other Means Of Identification
Refrigerant R-134a, when viewed through a sight glass, may
have a "milky" appearance due to the mixture of refrigerant and
lubricating oil. As the refrigerant and oil DO NOT exhibit a "clear"
sight glass on a properly charged A/C system, most R-134a systems have
no sight glass.
REFRIGERANT OILS
NOTE: Use ONLY the specified oil for the appropriate system or A/C
compressor. Always check vehicle underhood A/C specification
label or A/C compressor label before adding refrigerant oil
to A/C compressor/system. See Figs. 2 and 3. Always use
refrigerant oil specified on vehicle underhood A/C
specification label if different from the following list.
Refrigerant R-12 based systems use mineral oil, while R-134a
systems use Polyalkylene Glycol (PAG) oils. Using a mineral oil based
lubricant with R-134a will result in A/C compressor failure due to
lack of proper lubrication. The following R-134a refrigerant oils are
currently specified:
Use DENSO/ND-Oil 8 refrigerant oil on Nippondenso
compressors. Use SUN PAG 56 refrigerant oil on Sanden compressors.
NOTE: PAG oils absorb moisture very rapidly, 2.3-5.6 percent by
weight, as compared to a mineral oil absorption rate of
0.005 percent by weight.
SERVICE EQUIPMENT
A/C systems using R-134a refrigerant and PAG lubricants
cannot use R-12 refrigerant or mineral oil lubricants. R-134a
refrigerant is NOT compatible or interchangeable with R-12
refrigerant. Separate sets of hoses, manifold gauge sets and
recovery/recycling equipment are required to service the different
systems. This is necessary to avoid cross-contaminating and damaging
A/C system. A single set of A/C service equipment cannot be cleaned
thoroughly enough to be used with both types of refrigerant.
All equipment used to service A/C systems using R-134a must
be U.L. listed and certified to meet SAE standard J2210. The service
hoses on the manifold gauge set must have manual (turn wheel) or
automatic back-flow valves at the service port connector ends. This
will prevent refrigerant from being released into the atmosphere.
For identification purposes, R-134a service hoses must have a
Black stripe along its length and be clearly labeled SAE J2196/R-134a.
The low pressure test hose is Blue with a Black stripe. The high
pressure test hose is Red with a Black stripe, and the center test
hose is Yellow with a Black stripe.
R-134a manifold gauge sets can be identified by one or all of
the following: Labeled FOR USE WITH R-134a on set, labeled HFC-134a or
R-134a on gauge face, or by a Light Blue color on gauge face. In
addition, pressure/temperature scales on R-134a gauge sets are
different from R-12 manifold gauge sets.
SYSTEM SERVICE VALVES
SCHRADER-TYPE VALVES
NOTE: Although similar in construction and operation to a tire
valve, NEVER replace a Schrader-type valve with a tire valve.
Page 141 of 1501
than 0.5 volt or more than 4.5 volts, or an open or short
circuit in "G" sensor system.
1) Disconnect "G" sensor connector. Sensor is located on
bracket under center console, next to shifter. See Fig. 10. Connect
Special Tool (MB991348) between sensor and connector. Using a DVOM,
check voltage between sensor connector terminals No. 2 (Blue/White
wire) and No. 3 (Black/Red wire). Voltage should be 2.38-2.62 volts.
If voltage is as specified, reconnect sensor connector and go to step
3). If voltage is not as specified, leave special tool and DVOM
connected and go to next step.
2) Note top center position of sensor, and remove sensor. See
"G" SENSOR under REMOVAL & INSTALLATION . Secure sensor so that arrow
on sensor is facing straight down. Voltage should be 3.4-3.6 volts. If
voltage is specified, reinstall sensor and go to next step. If voltage
is not as specified, replace sensor.
3) Turn ignition off. Disconnect ECU 26-pin connector. Turn
ignition on. Check voltage between ECU 26-pin connector terminals No.
4 and 17. See Figs. 5-6. Voltage should be 2.4-2.6 volts. If voltage
is as specified, go to next step. If voltage is not as specified,
check and repair connectors and related wiring harness between ECU and
sensor. See WIRING DIAGRAMS .
4) Check and repair ECU 26-pin connector. If connector is
okay, replace ECU.
Fig. 10: Locating "G" Sensor
Courtesy of Mitsubishi Motor Sales of America.
DTC 33: STOPLIGHT SWITCH SYSTEM
Page 235 of 1501
cavity and contact surfaces. Install oil seal using seal driver. Press
new oil seal into bearing case until it is flush with face of bearing
case. Install backing plate and bearing case.
2) Apply grease to external surfaces of bearing outer race.
Press bearing outer race into bearing case. Install rear brake
assembly and bearing case. Pack bearing case and axle threads with
grease. Install new retainer ring and snap ring.
3) Using a feeler gauge, measure clearance between snap ring
and new retainer ring. Clearance should be less than 0.0065" (0.165
mm). If clearance exceeds specification, install a new selective snap
ring to bring clearance to specification. See SNAP RING THICKNESS
SPECIFICATION table.
SNAP RING THICKNESS SPECIFICATION
\
\
\
\
\
\
\
Thickness: In. (mm) Color\
0.060 (1.52) ................................................... Red\
0.067 (1.70) ................................................ Purple\
0.073 (1.85) .................................................. Blue\
0.079 (2.01) ................................................ Yellow\
0.085 (2.16) ............................................... Neutral\
\
\
\
\
\
\
\
4) Check condition of oil seal and replace as necessary.
Install axle shaft assembly into axle housing. Tighten bearing
retainer bolts to 65 ft. lbs (15 N.m.). To complete installation,
reverse removal procedure.
REAR AXLE HUB BEARINGS
NOTE: Rear hub bearings are not serviceable on FWD models.
Removal & Installation (FWD Models)
1) Raise and support vehicle. Remove wheels. Remove wheel
speed sensor (if equipped). On models with drum brakes, remove brake
drum and shoes. See REAR BRAKE DRUM & SHOES .
2) On models with disc brakes, remove caliper and rotor. On
all models, remove hub bolts or spindle nut and hub assembly. To
install, reverse removal procedure. Tighten hub bolts or spindle nut
to specification. See HUB TIGHTENING TORQUE table. Rotate brake drum
or disc to ensure free movement.
NOTE: Rear hub bearings are not serviceable on Eclipse AWD models.
Removal & Installation (Eclipse AWD)
1) Raise and support vehicle. Remove wheels. Remove wheel
speed sensor (if equipped). On models with drum brakes, remove brake
drum and shoes. See REAR BRAKE DRUM & SHOES .
2) On models with disc brakes, remove caliper and rotor. On
all models, remove axle nut. Remove 4 hub bolts and hub assembly. To
install, reverse removal procedure. Tighten hub bolts to
specification. See HUB TIGHTENING TORQUE table. Rotate brake drum or
disc to ensure free movement.
HUB TIGHTENING TORQUE
\
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Hub Mounting Bolts ................................... 54-65 (74-85)\
Spindle Nut
Mirage ................................................. 127 (172)\
3000GT FWD ............................................. 170 (230)\
Page 276 of 1501
ELECTRIC COOLING FAN
COMPONENT TESTING
Radiator Fan Motor (Diamante)
1) Disconnect radiator fan motor connectors A39 and A40.
Ground fan motor connector A39 terminal No. 2 (Black wire). Using a
fused jumper wire, connect battery voltage to fan motor connector A39
terminal No. 1 (Blue/Black wire). See Fig. 7. See WIRING DIAGRAMS. Fan
motor should operate at low speed with no abnormal noises or
interferences. Repair or replace components as necessary.
2) Ground fan motor connector A39 terminal No. 2 (Black wire)\
and connector A40 terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector A39 terminal No.
1 (Blue/Black wire). See Fig. 7. See WIRING DIAGRAMS. Fan motor should
operate at medium speed with no abnormal noises or interferences.
Repair or replace components as necessary.
3) Ground fan motor connector A39 terminal No. 2 (Black wire)\
and connector A40 terminal No. 2 (Black wire). Using 2 fused jumper
wires, connect battery voltage to fan motor connector A39 terminal No.
1 (Blue/Black wire) and to connector A40 terminal No. 1 (Green wire)\
.
See Fig. 7. See WIRING DIAGRAMS. Fan motor should operate at high
speed with no abnormal noises or interferences. Repair or replace
components as necessary.
Fig. 7: Testing Radiator Fan Motor (Diamante)
Courtesy of Mitsubishi Motor Sales of America.
Radiator Fan Motor (Eclipse)
1) Disconnect radiator fan motor 4-pin connector. Ground fan
Page 277 of 1501
motor connector terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 1
(White/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
2) On all models except 1998 2.0L non-turbo, ground fan motor
4-pin connector terminal No. 4 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 3
(White/Blue wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
Radiator Fan Motor (Galant)
1) Disconnect radiator fan motor 4-pin connector. Ground fan
motor connector terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 1
(Blue wire). See WIRING DIAGRAMS. Fan motor should operate with no
abnormal noises or interferences. Repair or replace components as
necessary. If no problems exist, go to next step.
2) Ground fan motor 4-pin connector terminal No. 4 (Black
wire). Using a fused jumper wire, connect battery voltage to fan motor
connector terminal No. 3 (Blue/Black wire). See WIRING DIAGRAMS. Fan
motor should operate with no abnormal noises or interferences. Repair
or replace components as necessary.
Radiator Fan Motor (Mirage)
Disconnect radiator fan motor 2-pin connector. Ground fan
motor 2-pin connector terminal No. 2 (Black wire). Using a fused
jumper wire, connect battery voltage to 2-pin connector terminal No. 1
(Blue/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
Radiator Fan Motor (3000GT)
1) Disconnect radiator fan motor 4-pin connector. Ground fan
motor connector terminal No. 4 (Blue/Green wire). Using a fused jumper\
wire, connect battery voltage to fan motor connector terminal No. 2
(Red/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary. If radiator fan motor operates as specified, go to next
step.
2) Disconnect battery voltage and ground from radiator fan
motor 4-pin connector. Using an ohmmeter, measure resistance between
radiator fan motor 4-pin connector terminals No. 1 (Black wire) and
No. 3 (Yellow/Blue wire). See WIRING DIAGRAMS. Resistance should be 0.
29-0.35 ohms. Replace radiator fan motor if resistance is not as
specified.
Condenser Fan Motor (Diamante)
1) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 1 (Blue/White wire).
Connect ground to connector terminal No. 2 (Black wire). Fan motor
should operate with no abnormal noises or interferences. Repair or
replace components as necessary. If no problems exist, go to next
step.
2) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 3 (Yellow wire). When\
terminal No. 4 (Black wire) is connected to ground, condenser fan
should operate faster. Replace condenser fan if operation is not as
specified. Ensure there are no abnormal noises or interferences during
fan operation.
Condenser Fan Motor (Eclipse)