Indicator MITSUBISHI MONTERO 2000 Service User Guide

ENGINE AND EMISSION CONTROL -Auto-cruise Control System17-23
Inspection Procedure 7
Hunting (repeated acceleration and deceleration) occurs
at the set vehicle speed.
Probable cause
The cause is probably a malfunction of vehicle speed sensor or GE actuator (electronic
governor).
In either case, a diagnosis code regarding the diesel fuel system must be confirmed.DMalfunction of the vehicle speed sensor
DMalfunction of the GE actuator (electronic governor)
DMalfunction of the engine-ECU
MUT-II Self-Diag code
Is a diagnosis code regarding the diesel fuel system output?YES
NO
Check trouble symptoms.NGReplace the engine-ECU.
Follow the troubleshooting regarding the diesel fuel system. (Refer
to GROUP 13C.)
Inspection Procedure 8
When the MAIN switch of the auto-cruise control switch is
turned on, the auto-cruise control indicator lamp does not
illuminate. (However, the auto-cruise control in normal.)
Probable cause
There may be a burnt-out bulb or a malfunction of the auto-cruise control indicator
lampcircuit.DBurnt-out bulb
DMalfunction of the harness
DMalfunction of the connector
DMalfunction of the engine-ECU
OK
Auto-cruise control indicatorlamp bulbcheckNG
Replace
NG
Repair
OK
NG
OK
Check trouble symptom.
NG
Check the harness between the J/B and the combination meter,
and repair if necessary.
Check the following connectors:
D-02, E-10, D-110
OK
Check trouble symptom.
NG
Repair
NG
Replace the engine-ECU.NG
Measure at the engine-ECU connector D-110.
DDisconnect the connector and measure at the harness side.
DIgnition switch and auto-cruise control MAIN switch: ON
DVoltage between terminal 22 and earth
OK:System voltage
Measure at the combination meter connector D-01.
DDisconnect the connector and measure at the harness side.
DIgnition switch and MAIN switch: ON
DVoltage between terminal 62 and earth
OK:System voltageCheck the following connector:D-01
NG
Check the harness between the combination meter and the engine-
ECU, and repair if necessary. OK
Check trouble symptom.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

22-1
MANUAL
TRANSMISSION
CONTENTS
GENERAL INFORMATION 2..................
LUBRICANTS 2..............................
SEALANTS 2................................
SPECIAL TOOL 2............................
TROUBLESHOOTING <SS4 II> 3.............
ON-VEHICLE SERVICE 6.....................
Transmission Oil Check 6.......................
Oil Replacement 6.............................4WD Detection Switch Continuity Check
<V5MT1> 7...................................
High/Low Detection Switch Continuity Check
<V5MT1> 7...................................
TRANSMISSION CONTROL <V5MT1> 8.......
TRANSMISSION CONTROL <V5MT3> 9.......
TRANSMISSION ASSEMBLY 10..............
4WD INDICATOR-ECU/TRANSFER-ECU 17....


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

MANUAL TRANSMISSION -4WD Indicator-ECU/Transfer-ECU22-18
Terminal No.Inspection itemInspection condition
1: Ignition switchInspection condition
2: Transfer lever positionTerminal voltage
1Free wheel engageON2HSystem voltage
switch
4H*10V
24WD detectionON2HSystem voltage
switch
4H, 4L0V
3Ignition switch (IG1)OFF-0V
ON-System voltage
6HI/LOW detection
switchONShifting from 4H to 4L
or vice versaSystem voltage
2H, 4H, 4L0V
7Free wheel clutchON4H, 4L0V
changeover solenoid
valve
2H*2System voltage
104WD Indicator lampON2H0V
4H, 4LSystem voltage
NOTE
*1:When vehicle has been moved once.
*2:Shift the lever from 4H to 2H, and then turn the ignition switch to OFF and then back to ON.
TRANSFER-ECU
Measure the terminal voltage (Refer to P.22-3).


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

23-1
AUTOMATIC
TRANSMISSION
CONTENTS
SERVICE SPECIFICATIONS 2.................
LUBRICANTS 2..............................
SPECIAL TOOLS 2..........................
TROUBLESHOOTING
<A/T> 3.....................................
<SS4II
>70................................
<Shift Lock and Key Interlock Mechanisms>
92 ..........................................
ON-VEHICLE SERVICE 94...................
Basic Adjustment Procedures 94.................
Transfer Oil Check 99...........................
Transfer Oil Change 99.........................
Location of Control Components 101..............
Control Component Checks 102..................
Torque Converter Stall Test 105..................
Fluid Pressure Test 106.........................Hydraulic Circuit 110............................
Line Pressure Adjustment 111...................
Selector Lever Operation Check 111..............
Transfer Shift Lever Operation Check 114........
Transmission Control Cable Adjustment 114......
Transfer-ECU Check 115........................
Position Indicator Lamp Check 115...............
TRANSMISSION CONTROL* 116.............
SHIFT LOCK AND KEY INTERLOCK
MECHANISMS* 120..........................
TRANSMISSION ASSEMBLY 122.............
TRANSMISSION OIL COOLER 127...........
A/T-ECU 129................................
TRANSFER-ECU 130........................
WARNING REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring, and interconnecting
wiring. Other SRS-related components (that mayhave to be removed/installed in connectionwith SRS service or maintenance) are
indicated in the table of contents by an asterisk(*).


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-5
ROAD TEST
No.Pre-test/opera-
tion conditionsTest/operationJudgment valueCheck itemDiag-
nosis
code
No.Inspection pro-
cedure if there is
an abnormality
1Ignition switch:
OFFIgnition switch
(1) ONData List No. 54
(1) 10 - 12 VA/T control
relay54A/T control relay
system
2Ignition switch:
ON
Engine:Stop
Selector lever
position: PSelector lever posi-
tion
(1) P
(2) R
(3) N
(4) DData List No. 61
(1) P
(2) R
(3) N
(4) DInhibitor
switch-Inhibitor switch
system
Selector lever opera-
tion
(1) D (1st)
(2) Sports mode se-
lected (1st)
(3) Lever moved toData List
No.67 No.68 No.69
(1)OFF OFF OFF
(2)ON OFF OFF
(3)ON ON OFF
(4)ON OFF ON
Select switch
Upshift
switch
Downshift
switch-Sports mode
switch system
upshift position
and held (2nd)
(4) Lever moved to
downshift
position and held
(1st)Shift indicator lamp
(1) D and 1
illuminate
(2) Only 1
illuminates
(3) Only 2
illuminates
(4) Only 1
illuminates
Accelerator pedal
(1) Fully closed
(2) Depressed
(3) Fully openedData List No. 11
(1) 985 - 1,085 mV
(2) Gradually in-
creases from (1)
(3) 4,000 mV or
moreAPS11
12
14APS system
Data list No.25
(1) OFF
(2) ONWide open
throttle
switch25Wide open
throttle switch
system
2Ignition switch:
ON
Engine: StopBrake pedal
(1) Depressed
(2) ReleasedData List No. 26
(1) ON
(2) OFFStop lamp
switch26Stop lamp
switch system
Selector lever
position: PTransfer shift lever
position
(1) Except for 4LLc
(2) 4LLcData List No. 75
(1) OFF
(2) ON4LLc switch-4LLc switch sys-
tem


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-20
Code No. 22 Input shaft speed sensor systemProbable cause
If no output pulse from the input shaft speed sensor is detected for 1 second or
more while the vehicle is driving at 30 km/h or more in 4th, it isjudged that
there is a short-circuit oropencircuit in the input shaft speed sensor, and code
No. 22 is output.
If code No. 22 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of input shaft speed sensor
DMalfunction of reverse clutch retainer
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-121,<4M4>D-108
To the nextpage
NG
OKNG
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 22 Input shaft speed sensor
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
NG
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-23
DIgnition switch: ON
D<6G7> Voltage between terminal
103 and earth
D<4M4> Voltage between terminal
31 and earth
OK:4.8 - 5.2 V
Measure the output wave pattern of
the input shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 103 of
D-122
D<4M4> Voltage between terminal
31 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-22
Code No. 23 Output shaft speed sensor systemProbable cause
If the output from the output shaft speed sensor is 50% or less continuously for
1 second or more while the vehicle is driving at 30 km/h or more in 4th, it is
judged that there is ashort-circuit oropencircuit in the output shaft speed
sensor, and code No. 23 is output.
If code No. 23 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of output shaft speed sensor
DMalfunction of direct planetary carrier
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NG
Repair
NG
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-122,<4M4>D-108
To the nextpage
NG
OK
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 23 Output shaft speed
sensor system
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
OK
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7>Voltage between terminals
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-02
DIgnition switch: ON
D<6G7>Voltage between terminals
104 and earth
D<4M4> Voltage between terminal
32 and earth
OK:4.8 - 5.2 VNG
Measure the output wave pattern of
the output shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 104 of
D-122
D<4M4> Voltage between terminal
32 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
Repair
NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-26
Code No. 31 LR solenoid valve systemProbable cause
If the drive terminal voltage of the LR solenoid valve is 3.0 V or less, it is
judged that there is ashort-circuit oropencircuit in the LR solenoid valve, and
the corresponding code is output.
The transmission will be fixed in 3rd as a fail-safe measure, and the N range
indicator will flash at a rate of 1 Hz.DMalfunction of LR solenoid valve
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NO
YES
OK
MUT-
IISelf-Diag Code
DIs code No. 54 output?Code No. 54 - A/T control relay system check
(Refer to P.23-103.)
OK NG
Transient malfunction
(Refer to GROUP 00 - Points to Note for Transient
Malfunctions.)MUT-
IIActuator Test
DNo. 1 LR solenoid valve
OK:Sound of operation can be heard
OK
Check the following connectors:<6G7> D-122,<4M4>D-109
OK
NG
NG
Replace the engine-A/T-ECU or A/T-ECU.
Repair
OK
Check the trouble symptoms.
OK
NG
Check the following connectors:E-113, D-12
NG
Repair
Check the harness between the solenoid valve assembly and
the A/T control relay, and repair if necessary.
Check the following connectors:<6G7> D-122, E-113, D-12
<4M4> D-109, E-113,D-12NG
NG
RepairCheck the following connector:C-04
Replace the LR solenoid valve
L
OK
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the solenoid
valve side.
DResistance between terminals 6 and 10
OK:2.7 - 3.4
W
OK
Measure at engine-A/T-ECU connector D-122 <6G7>, or at
A/T-ECU connector D-109 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal 129 and earth
D<4M4> Voltage between terminal 62 and earth
OK:System voltage
DCheck the harness between the solenoid valve assembly
and the engine-A/T-ECU, and repair if necessary. <6G7>
DCheck the harness between the solenoid valve assembly
and the A/T-ECU, and repair if necessary.<4M4>
DCheck the harness between the solenoid valve assembly
and the A/T control relay, and repair if necessary.NG
Repair
NG
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal 10 and earth
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-27
Code No. 32 UD solenoid valve systemProbable cause
If the drive terminal voltage of the UD solenoid valve is 3.0 V or less, it is
judged that there is ashort-circuit oropencircuit in the UD solenoid valve, and
the corresponding code is output.
The transmission will be fixed in 3rd as a fail-safe measure, and the N range
indicator will flash at a rate of 1 Hz.DMalfunction of UD solenoid valve
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NO
YES
OK
MUT-
IISelf-Diag Code
DIs code No. 54 output?Code No. 54 - A/T control relay system check
(Refer to P.23-103.)
OKNG
Transient malfunction
(Refer to GROUP 00 - Points to Note for Transient
Malfunctions.)MUT-
IIActuator Test
DNo.2 UD solenoid valve
OK:Sound of operation can be heard
OK
Check the following connectors:<6G7> D-122,<4M4>D-107
OK
NG
NG
Replace the engine-A/T-ECU or A/T-ECU.
Repair
OK
NG
Check the trouble symptoms.
OK
NG
Check the following connectors:E-113, D-12
NG
Repair
Check the harness between the solenoid valve assembly and
the A/T control relay, and repair if necessary.
Check the following connectors:<6G7> D-122, E-113, D-12,
<4M4> D-107, E-113,D-12NG
NG
RepairCheck the following connector:C-04
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminals 9 and earth
OK:System voltage
Replace the UD solenoid valve.
L
OK
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the solenoid
valve side.
DResistance between terminals 3 and 9
OK:2.7 - 3.4
W
OK
Measure at engine-A/T-ECU connector D-122 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal 120 and earth
D<4M4> Voltage between terminal 1 and earth
OK:System voltage
DCheck the harness between the solenoid valve assembly
and the engine-A/T-ECU, and repair if necessary. <6G7>
DCheck the harness between the solenoid valve assembly
and the A/T-ECU, and repair if necessary.<4M4>
DCheck the harness between the solenoid valve assembly
and the A/T control relay, and repair if necessary.NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting <A/T>23-28
Code No. 33 2nd solenoid valve systemProbable cause
If the drive terminal voltage of the 2nd solenoid valve is 3.0 V or less, it is
judged that there is ashort-circuit oropencircuit in the 2nd solenoid valve, and
the corresponding code is output.
The transmission will be fixed in 3rd as a fail-safe measure, and the N range
indicator will flash at a rate of 1 Hz.DMalfunction of 2nd solenoid valve
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NO
YES
OK
MUT-
IISelf-Diag Code
DIs code No. 54 output?Code No. 54 - A/T control relay system check
(Refer to P.23-103.)
OK NG
Transient malfunction
(Refer to GROUP 00 - Points to Note for Transient
Malfunctions.)MUT-
IIActuator Test
DNo. 3 2nd solenoid valve
OK:Sound of operation can be heard
OK
Check the following connectors:<6G7> D-122,<4M4>D-107
OK
NG
NG
Replace the engine-A/T-ECU or A/T-ECU.
Repair
OK
Check the trouble symptoms.
OK
NG
Check the following connectors:E-113, D-12
NG
Repair
Check the harness between the solenoid valve assembly and
the A/T control relay, and repair if necessary.
Check the following connectors:<6G7> D-122, E-113, D-12,
<4M4> D-107, E-113,D-12NG
NG
RepairCheck the following connector:C-04
Replace the 2nd solenoid valve.
L
OK
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the solenoid
valve side.
DResistance between terminals 4 and 9
OK:2.7 - 3.4
W
OK
Measure at engine-A/T-ECU connector D-122 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal 106 and earth
D<4M4> Voltage between terminal 16 and earth
OK:System voltage
DCheck the harness between the solenoid valve assembly
and the engine-A/T-ECU, and repair if necessary. <6G7>
DCheck the harness between the solenoid valve assembly
and the A/T-ECU, and repair if necessary.<4M4>
DCheck the harness between the solenoid valve assembly
and the A/T control relay, and repair if necessary.RepairNG
NG
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminals 9 and earth
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk