wiring MITSUBISHI MONTERO 2000 Service Owner's Manual

CHASSIS ELECTRICAL -Clock or Center Display54A-62
INSPECTION PROCEDURE 1
No display appears after the ignition key is turn to the ACC position.
OK
Measure voltages between D-03 display connector terminal (25),
(26) voltage and earth.
DIgnition switch: ACC
OK:System voltageNGRepair the fuse and wiring harness.
OK
Measure resistance between D-03 display connector terminal (28)
and earth.
OK:approx. 0
WNGRepair the wiring harness.
OK
Repair the center display unit.
Check the following connector: D-03NGRepair
INSPECTION PROCEDURE 2
Outside air temperature does not appear or abnormal outside air temperature appears.
<Vehicles without automatic air conditioner system>
Check the following connector: D-03NGRepair.
NO
Go to inspection procedure 3.
Check the wiring harness between the
Center Display and the outside air tem-
perature sensor.OKReplace the center display unit.OKEnd
NG
Replace the outside air temperature
sensor.NG
Check the wiring harness between the
center display unit and the outside air
temperature sensor, and replace if nec-
essary.
OK
Is a correct outside air temperature dis-
played in the servicemode?YESIs a correct vehicle speed displayed in
the servicemode?YESEnd (no abnormality).
NO
<Vehicles with automatic air conditioning system>
Select “Check of units connected into
the center display” on the service mode.
Does the symbol “AU” appear?NOGo to inspection procedure 7.
YES
Replace the center display unit.
YES
MUT-
IISelf-Diag code
Is A/C diagnosis code No.13 or 14 set?YESCheck the outside air temperature sen-
sor. (Refer to GROUP 55B.)
NO
Is a correct vehicle speed displayed in
the servicemode?NOGo to inspection procedure 3.
NOTE: It is necessary to drive for a while and get accurate temperature in display if you pass a area
in which temperature is much different. It might show high temperature on display in case it is high
around sensor due to high temperature of engine after battery is exchanged, or a display unit is reinstalled.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -Clock or Center Display54A-63
INSPECTION PROCEDURE 3
Abnormal vehicle speed is displayed on the service mode.
<Petrol-powered vehicles>
OK
NGRepair.
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 36 and
body earth.
OK:(Ignition switch: ON)
System voltage.
(Ignition switch: OFF)
0-1VNGCheck the wiring harness between the
center display unit and the junction
block, and repair if necessary.
NG
Check the wiring harness between the
center display unit and the engine-ECU,
and repair if necessary.
Select “Check of units connected into
the center display” on the service mode.
Does the symbol “MU” appear?YES NGDisconnect MUT-
II. Then check vehicle
wiring harnesses.Disconnect connector D-04.
Then check voltage at terminal 5 of that
connector.
DIgnition switch: ON
NG:More than 80% of system volt-
age
OK:Less than that
OK NO
OK
Check the connections between the
center display unit and the engine-ECU.OKReplace the center display unit.
Check the connector: D-04
<Diesel-powered vehicles>
Measure at center display unit connector D-03.
DDisconnect the connector.
DVoltage between terminal 36 and body earth.
OK:(Ignition switch: ON) System voltage.
(Ignition switch: OFF) 0 - 1 VNGCheck the wiring harness between the center display unit and
the junction block, and repair if necessary.
OK
Measure at center display unit connector D-03 .
DDisconnect the connector.
DVoltage between terminal 27 and body earth.
OK:HI: System voltage.
Lo: 0 - 1VNGCheck the wiring harness between the center display unit and
the vehicle speed sensor, and repair if necessary.
OK
Replace the center display unit.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -Clock or Center Display54A-64
INSPECTION PROCEDURE 4
Abnormal driving data are displayed:
DAbnormal average fuel consumption (momentary fuel consumption) and average vehicle speed
DAbnormal cruising distance
Are the average fuel consumption and average vehicle speed dis-
play correctly?NOGo to inspection procedure 3.1.
YES
Does the vehicle information on displayed on the screen meet
with the actual vehicle?
Is the vehicle type (long or short body) recognized correctly?
(Select “Check of units connected into the center display” and
“Check of vehicle information” on the service mode.)NOReplace the center display unit.
YES
Is remained fuel amount displayed correctly on servicemode?YESEnd (no abnormality).
NO
Measure at center display unit connector D-03.
DDisconnect the connector.
DVoltage between terminal 33 and body earth.
OK:0.1 - 3 VNGCheck the wiring harness between center display unit and the
fuel gauge unit, and repair ifnecessary. (relevant units: Combination
meter, fuel gauge unit)
OK
Replace the center display unit.
NOTE
(1) If the remained fuel amount is so small that the fuel gauge unit can not detect a correct amount,
incorrect cruising range may be displayed.
(2) Fuel consumption is updated each time fuel is supplied. Furthermore, the cruising range depends
on road and driving conditions.
INSPECTION PROCEDURE 5
Clock runs fast or slow.
NGRepair the fuse and wiring harness.
OK
YES
Does it receive a radio station on differ-
ent region where has timelag?YESTurn off the CT function.
NO
Replace the center display unit.
Measure at center display unit connec-
tor D-03.
DIgnition switch: OFF
DVoltage between terminal 26 and
body earth.
OK:System voltage
Is the symbol “CT” displayed?
NO


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -Clock or Center Display54A-65
INSPECTION PROCEDURE 6
The display screen is dim.
NOMeasure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 24 and
body earth.
OK:0 V (Lighting switch: off)
System voltage (Lighting
switch: ON)NGRepair the fuse and wiring harness.
Is the brightness of the center display
set correctly?NOAdjust the brightness of display on set-
ting mode.
OK
Replace the center display unit.
OK
Replace the center display unit.
YES
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DRheostat: max
DVoltage between terminal 32 and
body earth.
OK:Low voltage (0 - 3 V)NGRepair the wiring harness.
Does the brightness of display change
when the lighting switch is on or off?
YES


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -Clock or Center Display54A-66
INSPECTION PROCEDURE 7
Air conditioning display is not available.
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 36 and
body earth.
OK:System voltage (Ignition
switch: ON)
0 - 1 V (Ignition switch:
OFF)NGCheck the wiring harness between the
center display unit and the junction
block, and repair if necessary.
OK
NO OK
Check theaudio unit.
NG
NG
Repair wiring harness.
OK
OK
Replace the center display unit.
YES
Replace the A/C-ECU.
YES
Refer to GROUP 55 - A/C troubleshoot-
ing.Check the reoccurrence of symptom.OKEND
NG
Replace the center display unit.
Measure at center display unit connec-
tor D-04.
DDisconnect the connector.
DVoltage between terminal 9 and
body earth.
DVoltage between terminal 10 and
body earth.
DVoltage between terminal 19 and
body earth.
OK:Hi:4–5V
Lo:0–1V
Check the the wiring harnesses:
DBetween the center display and
A/C-ECU D-04, D-49
DBetween the center display and
AUDIO D-04, D-49
Check the reoccurrence of symptom.Select “Check of units connected into
the center display” on the service mode.
Does the symbol “AU” appear?
MUT-
IISelf-Diag code
Is the diagnosis code for A/C set?NG
NO


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -RV Meter54A-17
Termi-Input/out-
t
Signal sym-
bl
Terminal
lt
Harness problemTrouble symptoms when there is a
hblnal No.
p
put
gy
bolvoltage
(V)Open
circuitshort-cir-
cuit
yp
harness problem
11 - 1 4––––––
15Input/out-
putK (engine
K-LINE
signal)Hi: Sys-
tem volt-
age
Lo:0 - 1ExistsExistsDWiring communication error
DCommunication between the
engine-A/T-ECU <Petrol ve-
hicles> is not possible.
DAbnormal driving information
numerical display
16––––––
17Input/out-
putM-BUSY
(AUDIO)Hi:System
voltage
Lo:0 - 1ExistsExistsDAudio information does not
appear on the screen.
18–SHIELD-
EARTH
(AUDIO)––––
19Input/out-
putM-BUSY
(A/C)Hi:System
voltage
Lo:0 - 1ExistsExistsDAir conditioner information does
not appear on the screen.
DAmbient temperature is not
displayed.
20–SHIELD-
EARTH––––
22 - 21––––––
23InputAmbient
temperature
sensor–ExistsExistsDAmbient temperature is not
displayed.
24InputILL + (Light-
ing switch)Hi:System
voltage
Lo:0 - 1ExistsExistsDoes not illuminate.
25InputACC (ACC
power sup-
l)
System
voltageExists–Screen does not appear. No
operations are possible.
pp
ply)
g
–ExistsBlown multi-purpose fuse
26Input+BSystem
voltageExists–Screen does not appear. No
operations are possible.
g
–ExistsBlown multi-purpose fuse
27InputVSS (Vehicle
speed pulse
signal)Hi:System
voltage
Lo:0 - 1ExistsExistsDAbnormal “Distance km after
replacement” display in mainte-
nance screen
DSwitches which are not
supposed to operate during
driving do operate.
(Example:clock adjustment
screen, maintenance settings,
etc.)
DAmbient temperature display is
abnormally high.
28–Earth–Exists–Screen does not appear.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -RV Meter54A-19
Inspection procedure 3
Ambient temperature does not display normally.
OK
Ambient temperature sensor check
(Refer to GROUP 55B.)
NG
MUT-II diagnosis code
Is A/C diagnosis code No. 13 or No.
14 output?
Repair
Replace the RV meter. NG
Check the harness between the
A/C-ECU and the RV meter, and
repair if necessary.
Carry out a service function wiring
check.
Is the M-BUS signal normal?
YESNO
Replace the RV meter. NGNO
OK
Measure at RV meter connector D-39.
DConnector disconnected
DVoltage between terminal (27) and
body earth
OK:Hi: System voltage
Lo: 0 - 1 V
YES
Check the harness between the RV
meter and the vehicle speed sensor,
and repair if necessary.
Check the following connec-
tors:D-40, D-131
Carry out a service function wiring
check.
Is the SWS signal normal?Check the harness between the RV
meter and the ETACS-ECU, and
repair if necessary.NGMeasure at RV meter connector D-40.
DConnector disconnected
DVoltage between terminal (9) and
body earth
DVoltage between terminal (10) and
body earth
DVoltage between terminal (19) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
OK
OK
<Vehicles with automatic A/C>
Ambient temperature sensor check
(Refer to GROUP 55A.)
NGReplaceCarry out a service function wiring
check.
Is the ambient temperature sensor
signal normal?
YESNO
Replace the RV meter. NGNO
OKMeasure at RV meter connector D-39.
DConnector disconnected
DVoltage between terminal (27) and
body earth
OK:Hi: System voltage
Lo: 0 - 1 V
YES
Check the harness between the RV
meter and the vehicle speed sensor,
and repair if necessary.
Check the following connectors:
A - 30, D-27, D - 39
Carry out a service function wiring
check.
Is the SWS signal normal?Check the harness between the RV
meter and the ETACS-ECU, and repair if
necessary.
OK
<Vehicles without automatic A/C>
NO
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -RV Meter54A-21
Inspection procedure 5
Altimeter does not display normally.
NG
Replace the RV meter.
OKEnd (No abnormality)Carry out an altitude calibration mode check in service
mode.
Inspection procedure 6
Air conditioner information does not display normally.
NG
Replace the RV meter.
NG
Replace the RV meter.
(1)
Check the trouble symptoms. NO
MUT-II Self-diag code
Is A/C diagnosis code output?
Carry out a service function
communication and wiring check. One
of the following M-BUS outputs will
appear.
(1) E1 (Communication error)
(2) E2 (Open circuit or short-circuit)
(3) OKMeasure the wave pattern at RV meter
connector D-40.
DConnector disconnected
DVoltage between terminal (9) and
body earth
DVoltage between terminal (10) and
body earth
DVoltage between terminal (19) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
Malfunction of A/C-ECU OKMeasure the wave pattern at A/C-ECU
connector D-131.
DConnector disconnected
DVoltage between terminal (6) and
body earth
DVoltage between terminal (16) and
body earth
DVoltage between terminal (17) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V (2)Check the following
connectors:D-40, D-131
NG
OK
Check the harness between
the RV meter and the
A/C-ECU, and repair if
necessary. (3)
Refer to GROUP 55B - A/C
Troubleshooting.YES
OK
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

CHASSIS ELECTRICAL -RV Meter54A-22
Inspection procedure 7
Audio information does not display normally.
Replace the RV meter.
NG
Replace the radio and tape, CD
player
(1)
Check the trouble symptoms.
Carry out a service function
communication and wiring check. One
of the following M-BUS outputs will
appear.
(1) E1 (Communication error)
(2) E2 (Open circuit or short-circuit)
(3) OKMeasure the wave pattern at RV meter
connector D-40.
DConnector disconnected
DVoltage between terminal (7) and
body earth
DVoltage between terminal (8) and
body earth
DVoltage between terminal (17) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
Malfunction of radio and tape, CD
player OK
(2)
Check the harness between the RV
meter and the radio and tape, CD player,
and repair if necessary. (3)
YESOK
NG
Is error message “004” shown?NOReplace the RV meter.
NOTE:
The contents of error messages shown in the audio display screen are as follows:
Error messageLocation and cause of malfunction
EJECTA magazine for CD changeris not inserted.
NO DISCCD is not inserted.
ERROR 001Program error in audio
ERROR 002Error in CD disk
ERROR 003Mechanical error in audio system
ERROR 004Communication error in audio systemand RV meter,power supply error in audio
system, and other errors
ERROR HOTHeat protection for audio system


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SMART WIRING
SYSTEM (SWS)
Click on the applicable bookmark to selected the required model year.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk