MITSUBISHI OUTLANDER 2012 3.G Owners Manual

7-70 Vehicle care and maintenance
7
4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
BK0138000US.book 70 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

Vehicle care and maintenance
7-71
7
License plate lights
N00944000360
1. When removing the light unit (A), push it toward the left
side of the vehicle body.2. Use a screw driver to gently pry up the tab (B) and remove
the lens.
NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0138000US.book 71 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

7-72 Vehicle care and maintenance
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the light unit, insert tab (C) first then
align tab (D) with its hole.
BK0138000US.book 72 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

Vehicle care and maintenance
7-73
7
High-mounted stop light
N00943900102
NOTE
The high-mounted stop light uses an LED instead of the
bulb. Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when the light needs to
be repaired or replaced.
Dome light (front)/Reading lights
N00944500251
1. Insert a screwdriver into the notch of the light assembly.
Gently pry to remove the lens.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0138000US.book 73 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

7-74 Vehicle care and maintenance
7
2. While holding down the tab (A), pull out the bulb. 3. To install the bulb, perform the removal steps in reverse.
NOTE
Before replacing the bulb, put the dome light (front)/read-
ing lights switch into the “OFF” position.

When mounting the lens, align the tab (B) with the hole
on the vehicle body.
BK0138000US.book 74 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

Vehicle care and maintenance
7-75
7
Dome light (rear)/ Cargo room light
N00944100316
1. Insert a screwdriver into the notch of the light assembly
and pry gently to remove the lens.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. While holding down the tab (A), pull out the bulb.
BK0138000US.book 75 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

7-76 Vehicle care and maintenance
7
3. To install the bulb, perform the removal steps in reverse.NOTE
Before replacing the bulb, put the dome light (rear)/cargo
room light switch into the “OFF” position.

When mounting the lens, align the tabs (B) with the holes
on the vehicle body.
Glove compartment light
N00954200062
1. Turn the socket (A) counterclockwise to remove it.
BK0138000US.book 76 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

Vehicle care and maintenance
7-77
7
2. Pull out the bulb.
3. To install the bulb, perform the removal steps in reverse.
Vanity mirror lights
N00952800080
1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
BK0138000US.book 77 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

7-78 Vehicle care and maintenance
7
Center console down light
N00954700025
NOTE
The center console down light uses an LED instead of the
bulb. Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when the light needs to
be repaired or replaced.
Vehicle care precautions
N00945100166
In order to maintain the value of your vehicle, perform regular
maintenance using the proper materials and procedures. Be
sure to use only those materials and procedures that meet your
local environmental pollution control regulations. Choose the
materials you will use carefully, to be sure that they do not con-
tain corrosives. If you are not sure, contact an authorized Mit-
subishi Motors dealer for help in choosing these materials.
CAUTION
!
Cleaning products can be dangerous. Some are poi-
sonous and others are highly flammable. Some are
dangerous if you breathe their fumes in a closed
space. When you use anything in a container to
clean your vehicle, be sure to follow the instructions.
Always open your vehicle doors or windows when
you’re cleaning the inside. Never use the following
chemicals to clean your vehicle:
• Gasoline
• Carbon Tetrachloride
• Benzine
• Kerosene
• Naphtha
• Acetone
• Turpentine
• Paint Thinner
• Lacquer Thinner
• Nail Polish Remover
BK0138000US.book 78 ページ ２０１１年４月１３日　水曜日　午前１１時１７分

Vehicle care and maintenance
7-79
7
These can all be dangerous, and they all can damage your vehi-
cle.
Cleaning the inside of your vehicle
N00945200095
After washing the inside of your vehicle with any cleaner, wipe
it dry in a shady, well ventilated area.NOTE
Always read the instructions on the cleaner label.Plastic, vinyl leather, fabric and flocked parts
N00945300155
1. Lightly wipe these off with a soft cloth soaked in a 3%
solution of gentle soap and water.
2. To rinse, dip the cloth in fresh water, wring it out well, and
wipe off all the soap.
CAUTION
!
Do not use organic substances (solvents, benzine,
kerosene, alcohol, gasoline, etc.) or alkaline or acidic
solutions.
These chemicals can cause discoloring, staining or
cracking of the surface.
If you use cleaners or polishing agents, make sure
their ingredients do not include the substances men-
tioned above.
BK0138000US.book 79 ページ ２０１１年４月１３日　水曜日　午前１１時１７分