MITSUBISHI OUTLANDER PHEV 2020 (in English) Manual PDF

NOTE

zWhen the outside air temperature is low
and the following warning display ap- pears.
z When charging is completed.
z When the normal charge connector is
disconnected.
z When the charging stop operation is per-
formed by the quick charger.
z When the quick charging time has
passed 60 minutes.
z When the stop condition (charging
amount/charging time) on the quick charger is satisfied.
z When charging stops due to an electrical
power outage.
z When charging stops due to a failure.
z When operating the selector lever to the
“N” (NEUTRAL) position. (charging al-
so stops)
NOTEz Even when the operation mode automatical-
ly puts off, air conditioners, car navigation systems, audio equipment, etc. will stop.
Also, the vehicle status will be the same as putting the operation mode OFF (for exam-
ple: the lights go off, the room lamp is illu- minated or the electric mirrors are retracted).Automatic stop of the air con-
ditioner
In the following cases, the air conditioner au- tomatically stops. When the air conditioner stops, the air conditioner control panel turns
off.
z When the remaining amount of the drive
battery becomes low and the following
warning display appears.
Refer to “Warning display list” on page 6-25.
z When the temperature of the drive bat-
tery becomes extremely low and the fol-
lowing warning display appears.
Refer to “Warning display list” on page 6-25.
NOTEz To use the air conditioner again after the air
conditioner automatically stops, press the
power switch to turn the operation mode
OFF with the following message appeared, then press the power switch again to turn ON the operation mode of the power switch
so as to use the air conditioner.
Refer to “Warning display list” on page 6-25.
How to use an electric device during charging
3-262**(20(1Charging3

Energy flow display duringcharging
It shows the flow of energy during charging.
A: Various electrical devices
B: Drive battery
C: Charger
Blue arrow: Flow of electric energy
Display of energy flow (exam-
ple)
When charging the drive battery
When discharging from the drive battery
V2H power supply
No energy flow
NOTEz Even when you are not operating the air con-
ditioner, car navigation system, audio equip- ment, etc., since the on-board computer con-
sumes electricity, arrows may be displayed from the charger or the drive battery.NOTEz Energy flow display may change regardless
of the operation of the air conditioner, car
navigation system, audio equipment, etc.
z If you change the setting of the air condi-
tioner, it may take time until the display of
the energy flow stabilizes.
How to use an electric device during charging
3-272**(20(1Charging3

Charging troubleshooting guideSymptomPossible causePossible solutionCharging cannot be
started.The operation mode of the power
switch is in the “ON” position.Put the operation mode of the power switch in “OFF” before charging.The drive battery is already fully
charged.Charging cannot be performed if the drive battery is already fully charged. Charg- ing automatically turns off if the drive battery is fully charged.The temperature of the drive bat-
tery is too high or too low to
charge.Confirm the drive battery temperature.
Refer to “Cautions and actions to deal with intense heat” on page 2-10 and “Cau-
tions and actions to deal with intense cold” on page 2-10.The auxiliary battery is dis-
charged.The drive battery cannot be charged if the vehicle electrical systems cannot be
turned on. If the auxiliary battery is discharged, charge or emergency start the aux-
iliary battery.
Refer to “Emergency starting” on page 9-02.The vehicle or the charging cable
has a malfunction.The vehicle or charging cable may have a malfunction. Confirm if the warning
lamp on the meter is illuminated. Confirm if the indicator on the control box is in-
dicating a malfunction. If a warning is displayed, stop charging and contact a
MITSUBISHI MOTORS Authorized Service Point.Normal charging can-
not be started.There is no electrical power com-
ing from the outlet.Confirm that there has not been a power failure. Make sure the breaker is on. If an outlet with a timer device installed is used, power will only be available at the time set by the timer.
Confirm if the POWER indicator on the control box is illuminated.The charge connector is not con-
nected correctly.Confirm the charge connector is connected correctly.The charge connector was connec-
ted and disconnected repeatedly in
a short time.Disconnect the charge connector, wait for a while, then start charging procedure again from the beginning.
Charging troubleshooting guide
3-282**(20(1Charging3

SymptomPossible causePossible solutionA charging cable for other vehicle
is used.Use the EV charging cable only for your vehicle.A normal charger which does not
correspond to your vehicles is
used.Consult an administrator or a maker of the normal charger that it corresponds to
your vehicle. Also perform normal charging according to the operating procedure indicated on the body of normal charger.The reservation of Charging timer
is set up by MITSUBISHI Remote
Control (if so equipped), the
Smartphone-link Display Audio
(SDA) (if so equipped) or the
Smartphone-link Display Audio
(SDA) navigation system (if so
equipped).The normal charging cannot be started when the charging cable is connected, if the charging timer is set. Cancel all the charging timer settings, if you want to start thenormal charging immediately.
Refer to “MITSUBISHI Remote Control” on page 3-20.
For the Smartphone-link Display Audio (SDA) or the Smartphone-link Display Audio (SDA) navigation system, refer to the separate owner’s manuals.Normal charging is dis-
continued.There is no power coming from
the outlet.There may have been a electrical power failure, or the breaker may have failed. Charging will resume when the power source is reset.The EV charging cable has been
disconnected.Check that the EV charging cable has not been disconnected.The button on the normal charge
connector has been pressed.If the charge connector button is pressed for a long period of time, charging will be
stopped. Start the charging procedure again.The temperature of the drive bat-
tery is too high or too low to
charge.Confirm the drive battery temperature.
Refer to “Cautions and actions to deal with intense heat” on page 2-10 and “Cau-
tions and actions to deal with intense cold” on page 2-10.Charging is stopped by the normal
charge timer.Charging will stop depending on the timer function setting of the normal charge de- vice. Try it again with cancelling the timer settings.
Charging troubleshooting guide
3-292**(20(1Charging3

SymptomPossible causePossible solutionThe Charging timer was set up by
the MITSUBISHI Remote Control
(if so equipped), the Smartphone-
link Display Audio (SDA) (if so
equipped) or the Smartphone-link
Display Audio (SDA) navigation
system (if so equipped) after start-
ing of normal charging.Cancel all the charging timer settings. Charging is automatically restarted if you cancel the charging timer.
Refer to “MITSUBISHI Remote Control” on page 3-20.
For the Smartphone-link Display Audio (SDA) or the Smartphone-link Display
Audio (SDA) navigation system, refer to the separate owner’s manuals.Quick charging cannot
be started.The charge connector is not con-
nected correctly and/or not locked.Check that the charge connector is connected correctly and that it is locked.The self-diagnostic function of the
quick charge device returns a neg-
ative result.There is a possibility that the vehicle has a malfunction. Stop charging and contact
a MITSUBISHI MOTORS Authorized Service Point.The power switch of the quick
charger is off.Check the power switch of the quick charger.
Consult an administrator or a maker of the quick charger.Quick charge is discon-
tinued.Charging is stopped by the quick
charge timer.Charging will stop depending on the timer function setting of the quick charge de- vice. If you need to charge the drive battery more, start the charging procedureagain.Charging stops at 80 % capacity.Charging is designed to stop when the drive battery capacity reaches 80 %. If you
need to charge the drive battery more than 80 %, start the charging procedure again.The power supply for the quick
charger is off.Check whether the power supply for the quick charger is off.
Consult an administrator or a maker of the quick charger.
Charging troubleshooting guide
3-302**(20(1Charging3

SymptomPossible causePossible solutionThe charging indicator
is continuously blink-
ing even if the quick
charge connector is
not connected into the
quick charge port
when you start the
plug-in hybrid EV sys-
tem after quick charg-
ing.Quick charging has not finished
normally.Perform quick charging again and finish it normally or contact a MITSUBISHI
MOTORS Authorized Service Point.Plug-in Hybrid EV
System does not start
after quick charging.The vehicle has a malfunction.There is a possibility that the vehicle has a malfunction. After turning the operation
mode of the power switch to “ON” and putting the select position to “N”, ask the
support of the fellow passenger or people nearby to move the vehicle by pushing it
into safety.
After moving, contact a MITSUBISHI MOTORS Authorized Service Point.

Charging troubleshooting guide
3-312**(20(1Charging3

2**(20(1

Keys.................................................................................................... 4-02Electronic immobilizer (Anti-theft starting system)........................... 4-03
Keyless entry system...........................................................................4-03
Keyless operation system.................................................................... 4-07
Doors................................................................................................... 4-14
Central door locks............................................................................... 4-16
Dead Lock System*............................................................................ 4-16
“Child-protection” rear doors..............................................................4-18
Tailgate*.............................................................................................. 4-19
Electric tailgate*................................................................................. 4-20
Inside tailgate release.......................................................................... 4-26
Security alarm system*....................................................................... 4-27
Electric window control...................................................................... 4-34
Sunroof*.............................................................................................. 4-36Lockingandunlocking
2**(20(14

Keys
The key fits all locks.

without MITSUBISHI Remote Control
with MITSUBISHI Remote Control
1- Keyless operation key
2- Keyless operation key (with electric tail-
gate switch)
3- Emergency key:ARN,NGz When taking a key on flights, do not press
any switches on the key while on the
plane. If a switch is pressed on the plane, the key emits electromagnetic waves,which could adversely affect the plane’s
flight operation.
When carrying a key in a bag, be careful
that no switches on the key can be easily pressed by mistake.NOTEz The key (except for the emergency key) is a
precision electronic part with a built-in sig-
nal transmitter. Please observe the following in order to prevent a malfunction.