MITSUBISHI OUTLANDER SPORT 2013 3.G Owners Manual

7-10 Vehicle care and maintenance
7
To replace the oil filterThe oil filter should be replaced at the time or mileage speci-
fied in the “WARRANTY AND MAINTENANCE MAN-
UAL”.
Only use high quality replacement filters on this vehicle. The
manufacturer’s specifications for Genuine Mitsubishi oil filters
require that the filter can withstand a pressure of 256 psi (1.8
MPa). A Genuine Mitsubishi oil filter is the best replacement
filter.
Follow the installation instructions printed on the filter.
Engine coolant
N00937800584
To check the coolant levelThe engine coolant reserve tank (A) lets you quickly see when
you need to add coolant. When the engine is cold, the level of
the coolant in the reserve tank should be between the FULL
and LOW marks. The radiator usually stays full so there is no
reason to remove the radiator cap (B) except when you check
the coolant freeze point or replace the antifreeze coolant.
FULLLOW
BK0150700US.book 10 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-11
7
To add coolantMitsubishi Motors Genuine Coolant provides excellent protec-
tion against corrosion and rust formation on all metals, includ-
ing aluminum, and prevents clogs in some parts of the engine.
If you need to add coolant often, or if the level in the reserve
tank does not drop when the engine cools, the cooling system
should be pressure-tested for leaks. Take your vehicle to an
authorized Mitsubishi Motors dealer or a repair facility of your
choice for testing.
Radiator capThe radiator cap must be tight sealed to prevent losing coolant,
which may result in engine damage. Only use a Genuine
Mitsubishi Parts radiator cap, or an approved equivalent.Points to remember
Do not overfill the reserve tank.

Your vehicle uses a special radiator cap that stays sealed
and lets the coolant flow from the reserve tank back to the
radiator when the engine cools down. If you need to
change the cap, use the exact same kind.

Check the coolant freeze point in the radiator with the
proper gauge, and only when it is safe. If you add anti-
freeze, the contents of the reserve tank must be protected
against freezing.
Use “Mitsubishi Motors Genuine Super Long Life Coolant Pre-
mium” or equivalent*.
*: similar high quality ethylene glycol based non-silicate, non-
amine, non-nitrate and non-borate coolant with long life
hybrid organic acid technology
CAUTION
!
Do not use alcohol or methanol antifreeze or any
engine coolants that contain them. Using the wrong
antifreeze can corrode aluminum parts.
The required concentration of anti-freeze differs
depending on the expected ambient temperature.
Above -31 °F (-35 ° C) : 50 % concentration of anti-
freeze
Below -31 °F (-35 °C) : 60 % concentration of anti-
freeze
You can check the concentration level with a gauge
from an automotive supply store, or your authorized
Mitsubishi Motors dealer or service station can
check it for you.

Do not use water to adjust the concentration of cool-
ant.
Do not top off the tank with plain water only. Water
by itself boils at a lower temperature and does not
stop rust or freezing. If the water freezes, it will
damage your cooling system. Do not use tapwater. It
can cause corrosion and rust.
WARNING
!
Wait for the engine to cool down before opening the
radiator cap. Otherwise hot steam or boiling coolant
could spray up from the radiator and scald you.
CAUTION
!
BK0150700US.book 11 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-12 Vehicle care and maintenance
7

Keep the front of the radiator and condenser clean.

If the engine coolant temperature does not rise after the
engine is warmed-up, take your vehicle to an authorized
Mitsubishi Motors dealer or a repair facility of your
choice to have the thermostat checked, and replaced if
necessary.
Air cleaner filter
N00937900400
The air cleaner filter will get dirty and dusty from use and not
filter properly. Replace it with a new filter using the schedule
in the “WARRANTY AND MAINTENANCE MANUAL”.
1. Remove the upper cover and duct. For details, refer to “Removing and installing the upper cover and duct” on
page 7-14.
2. While holding down the tab (A), pull out the connector (B).
BK0150700US.book 12 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-13
7
3. Unclamp the cover. Open up the top of the cover and takeout the air cleaner filter. 4. Replacing the air cleaner filter and put the cover back on
in its original position.
NOTE
Genuine Mitsubishi Motors Parts are recommended when
replacing the air cleaner filter.

Make sure that the connector is properly reconnected.

After replacing the air cleaner filter, make sure that the
hinges at the bottom of cover are firmly set.
Type 1Type 2
CAUTION
!
Take care not to scratch the engine air flow sensor
when removing the air cleaner cover.
BK0150700US.book 13 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-14 Vehicle care and maintenance
7
5. Put the duct and upper cover back on in its original posi-tion. For details, refer to “Removing and installing the
upper cover and duct” on page 7-14.Removing and installing the upper cover and
ductTo replace the air cleaner filter, remove the upper cover and
duct.
To remove1. Remove the clips (A), and then remove the upper cover(B).
WARNING
!
Turn the ignition switch to the “OFF” position or
put the operation mode in OFF.
Make sure that your clothes cannot be caught by the
fan or drive belt. Personal injury could result.
BK0150700US.book 14 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-15
7
2. Remove the clips (C), and then remove the air duct (D).
To i n s t a l l1. Install the air duct (A), and then tighten the clips (B).
BK0150700US.book 15 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-16 Vehicle care and maintenance
7
2. Turn the upper cover over. Squeeze the head of the mould-ing clip (C) with pliers and remove the moulding. 3. Install the upper cover, and then attach the moulding (D).
NOTE

Attach the moulding with the wide part toward the front of
the vehicle.
BK0150700US.book 16 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-17
7
4. Install the clips (E).
Manual transaxle oil
(if so equipped)
N00938200178
Whenever the manual transaxle oil level is checked, add oil to
maintain the proper level, if necessary.
Refill or change the oil according to the table.Oil type
LubricantMitsubishi Motors Genuine NEW
MULTI GEAR OIL API Classifica- tion GL-3
Viscosity range SAE 75W-80
BK0150700US.book 17 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-18 Vehicle care and maintenance
7Continuously variable transmission (CVT)
fluid
(if so equipped)
N00938100089
The continuously variable transmission (CVT) should be main-
tained and serviced by an authorized Mitsubishi Motors dealer
or a repair facility of your choice to obtain the best perfor-
mance and longest life. It is important that the transmission
fluid is kept at the correct level.Fluid typeUse only “Mitsubishi Motors Genuine CVTF-J4” transmission
fluid to ensure optimum transmission performance.Special additivesDo not use any fluid additives to the transmission.
Transfer oil (All-wheel drive models)
N00938400271
Whenever the transfer oil level is checked, add oil as necessary
to maintain the proper level. Fill or change the oil according to
the table.Fluid type
Lubricant Mitsubishi Motors Genuine Super Hypoid
Gear Oil API classification GL-5
Viscosity range SAE 80
BK0150700US.book 18 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-19
7
Rear axle oil (All-wheel drive models)
N00915200269
Whenever the oil level is checked, add oil as necessary to
maintain the proper level.
Fill or change oil according to the table.Fluid type
Wa s h e r f l u i d
N00938600299
The windshield and rear window washer fluid reservoir is in
the engine compartment.
Check the washer fluid level at regular intervals and add
washer fluid to reservoir if necessary.
Open the reservoir cap and check the fluid level with the dip-
stick.
When freezing weather is anticipated, flush out the water in the
reservoir by operating the pump. Fill the reservoir with wind-
shield antifreeze (not radiator antifreeze), and operate the sys-
tem for a few seconds to flush out the residual water.
Lubricant
Mitsubishi Motors Genuine Super Hypoid
Gear Oil API classification GL-5
Viscosity range SAE 80
FULL
EMPTY
BK0150700US.book 19 ページ ２０１２年３月２２日　木曜日　午後６時４６分