MITSUBISHI OUTLANDER XL 2011 Owners Manual

Page 661 of 714

7-64 Vehicle care and maintenance
7
Side turn signal lights (on fender) (if so equipped)
N00943500111
NOTEIt is not possible to repair or replace only the bulb for the
side turn-signal light.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.
Side turn signal lights (on outside rearview mir-
ror) (if so equipped)
N00943500124
NOTEThe side turn signal lights (on outside rearview mirror)
uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.
BK0122500US.book 64 ページ 2010年5月12日 水曜日 午前11時11分

Page 662 of 714

Vehicle care and maintenance
7-65
7
Front fog lights
(if so equipped)
N00943600633
1. Turn the bezel (A) counterclockwise to remove it.2. Remove the 3 screws (B) and remove the light unit.*- Front of the vehicle
*- Front of the vehicle
BK0122500US.book 65 ページ 2010年5月12日 水曜日 午前11時11分

Page 663 of 714

7-66 Vehicle care and maintenance
7
NOTEWhen unfastening the screws, be careful not to move the
beam position adjustment screw (C).3. While holding down the tab (D), pull out the socket (E).
BK0122500US.book 66 ページ 2010年5月12日 水曜日 午前11時11分

Page 664 of 714

Vehicle care and maintenance
7-67
7
4. Turn the bulb (F) counterclockwise to remove it. 5. To install the bulb, perform the removal steps in reverse.
CAUTION
!Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.Never hold the halogen light bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the fog lights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0122500US.book 67 ページ 2010年5月12日 水曜日 午前11時11分

Page 665 of 714

7-68 Vehicle care and maintenance
7
Rear combination lights
N00943700432
1. Remove the screws (A) that hold the light unit and remove
the light unit.2. Turn the socket and bulb assembly counterclockwise to
remove it.
NOTEThe tail and stop light uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.B- Tail and stop light (LED) - cannot be replaced
C- Rear turn-signal light
BK0122500US.book 68 ページ 2010年5月12日 水曜日 午前11時11分

Page 666 of 714

Vehicle care and maintenance
7-69
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTEWhen mounting the light unit, align the clips (D) on the
light unit with the hole in the body.
BK0122500US.book 69 ページ 2010年5月12日 水曜日 午前11時11分

Page 667 of 714

7-70 Vehicle care and maintenance
7
Back-up lights
N00929100041
1. Open the tailgate.
2. Insert a screwdriver into the notch of the cover and pry
gently to remove the cover.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the cover.3. Turn the socket (A) counterclockwise to remove it.
BK0122500US.book 70 ページ 2010年5月12日 水曜日 午前11時11分

Page 668 of 714

Vehicle care and maintenance
7-71
7
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
Rear side-marker lights
N00935400094
1. Open the lower gate and pull back the cover between the
passenger compartment and the lower gate.
2. Remove the cover after you remove each of the 4 clips (A)
by inserting a screw driver into the clip groove and lever-
ing it toward the vehicle body.
BK0122500US.book 71 ページ 2010年5月12日 水曜日 午前11時11分

Page 669 of 714

7-72 Vehicle care and maintenance
7
3. Remove the light mounting screw (B) and remove the
light unit.4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
BK0122500US.book 72 ページ 2010年5月12日 水曜日 午前11時11分

Page 670 of 714

Vehicle care and maintenance
7-73
7
NOTEWhen mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
License plate lights
N00944000360
1. When removing the light unit (A), push it toward the left
side of the vehicle body.
BK0122500US.book 73 ページ 2010年5月12日 水曜日 午前11時11分

Page:   < prev 1-10 ... 621-630 631-640 641-650 651-660 661-670 671-680 681-690 691-700 701-710 ... 720 next >