MITSUBISHI SHOGUN 2008 Owner's Manual (in English)

Maintenance
8-41
8
Position lamps
E01003700471
1. Turn the bulb socket an
ticlockwise to remove it.
2. Remove the bulb from the socket by pulling out. 3. To install the bulb, perform the removal steps in reverse.
Front turn-signal lamps
E01003800414
1. Turn the bulb socket anticlockwise to remove it. 2. Remove the bulb from the socket by pulling out 3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
41 Wednesday, January 9, 2008 4:50 PM

8-42 Maintenance
8
Front fog lamps*
E01004000774
1. Remove the 5 clips (A, C) and screw (B) by following
procedures then turn up the cover (D).
2. Depress the tab (E) on the harness connector (F) and pull
the harness connector to remove it.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
42 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-43
8
3. Remove the entire socket and bulb assembly (G) by turn-
ing it anticlockwise.
4. To install the bulb, perform the removal steps in reverse.
CAUTION
!●
Handle halogen lamp bulbs with care. The gas inside halogen lamp bulbs is highly pressurized, so drop-ping, knocking, or scratc
hing a halogen lamp bulb
can cause it to shatter.
●
Never hold the halogen lamp bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the fog lamps are used.If the glass surface is dirt
y, it must be cleaned with
alcohol, paint thinner, etc., and refit it after drying thoroughly.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
43 Wednesday, January 9, 2008 4:50 PM

8-44 Maintenance
8
NOTE●
When refitting the clips of the cover, push the pin (H).
Rear combination lamps
E01004200659
On corner side1. Remove the screws that hold the lamp unit. 2. Slide the lamp unit out sideways to remove it.Left side
BK-BK2008E1ENUK.en-uk-Section11.fm Page
44 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-45
8
3. Remove the socket and bulb assemblies by turning it anti-
clockwise. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
Right side
A- Rear turn-signal lamp* B- Stop and tail lamp*
Stop lamp*
C- Reversing lamp 3-door models 5-door models
BK-BK2008E1ENUK.en-uk-Section11.fm Page
45 Wednesday, January 9, 2008 4:50 PM

8-46 Maintenance
8
On bumper
*
1. Remove the lens mounting screws.
2. Remove the socket and bulb assembly together by turning
it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.D- Rear turn-signal lamp E- Tail lamp
BK-BK2008E1ENUK.en-uk-Section11.fm Page
46 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-47
8
Rear fog lamp
E01004100241
1. Open the spare wheel garnis
h (A). (Refer to “To remove
the spare tyre” on page 6-18.)
2. Remove the socket and bulb assembly (B) by turning it
anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
47 Wednesday, January 9, 2008 4:50 PM

8-48 Maintenance
8
High-mounted stop lamp
E01004500362
1. Insert the tip of a blade (or
minus) screwdriver at the edge
of the cover and pry gently to remove the cover.
2. Remove the socket and bulb assembly together by turning
it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
48 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-49
8
Licence plate lamps
E01004600477
1. Remove the lens mounting screws and remove the socket
and bulb assembly.
2. Remove the socket and bulb assembly (A) together by
turning it anticlockwise and then remove the bulb by pull- ing it out.
3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
49 Wednesday, January 9, 2008 4:50 PM

8-50 Maintenance
8
NOTE●
When installing the lens, make
sure the direction of the
lens is installed as shown in the illustration. *: Right side of the vehicle
Room & map lamps
E01004700306
1. Insert a straight blade (or minus) screwdriver with a cloth
over its tip into the lens and pry gently to remove it.
2. Remove the bulb from the lamp holder. 3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
50 Wednesday, January 9, 2008 4:50 PM