wheel torque MITSUBISHI TRITON 1997 Workshop Manual

AUTOMATIC TRANSMISSION ± On-vehicle Service23-19
CONVERTER STALL TEST 23100540138
In this test, the engine maximum speed when the
torque converter stalls with the shift lever in the
ªDº or ªRº range is measured to check operation
of the torque converter, starter and one-way clutch
and check holding performance of the transmission
clutch (including brake).
Caution
Do not stand in front or at rear of the vehicle
during this test.
(1) Check the transmission fluid level. The fluid
temperature should be at the level after normal
operation (70 ± 80
C). The engine coolant
temperature should also be at the level after
normal operation (80 ± 90
C).
(2) Apply chocks to the rear wheels (right and left).
(3) Mount an engine tachometer.
(4) Apply fully the parking and service brakes.(5) Start the engine.
(6) With the selector lever in the ªDº range, fully
depress the accelerator pedal and read off the
engine maximum speed.
Standard value:
2,100 ± 2,400 r/min <4G63>
2,300 ± 2,600 r/min <4D56>
NOTE
When doing so, do not keep the engine running
with throttle full open for more than 5 seconds.
If two or more stall tests are needed, place
the selector lever in the ªNº position and run
the engine at about 1,000 r/min to allow the
transmission fluid to cool before another stall
test.
(7) Place the selector lever in the ªRº range and
perform the test as above.
JUDGEMENT OF STALL TEST RESULTS
Stall speed in ªDº and ªRº range is equal to each other
but lower than the nominal value.(1) Engine output is low.
(2) Starter one-way clutch is faulty. (Faulty torque
converter is suspected if it is lower than nominal
by more than 600 r/min)
Stall speed in ªDº range is higher than nominal.(1) Overdrive clutch slipping
(2) Overdrive one-way clutch faulty
(3) Forward clutch slipping
(4) One-way clutch No. 2 faulty
(5) Low line pressure
Stall speed in ªRº range is higher than nominal.(1) Overdrive clutch slipping
(2) Overdrive one-way clutch faulty
(3) Direct clutch slipping
(4) Brake No. 3 slipping
(5) Low line pressure

FRONT AXLE ± General Information26-2
GENERAL INFORMATION26100010111
2WD
The front hub assembly which uses a double taper
roller bearing is mounted on the knuckle spindle.For vehicles with ABS, a rotor for detecting the
wheel speed is press-fitted into the front hub.
4WD
The front axle consists of the hub assembly, drive
shaft, inner shaft, front differential, freewheel clutch
assembly and actuator. The features are:

The wheel bearing uses a double taper roller
bearing. For vehicles with ABS, a rotor for
detecting the wheel speed is bolted to the brake
disc.

Drive shafts of almost identical length reduce
torque steer. In addition, a D.O.J.-B.J.-type
constant velocity ball joint has high power
transmission efficiency and reduces vibration
and noise.
A vacuum-type freewheel clutch has been
adopted in the freewheel mechanism. Its
solenoid valve and actuator switch powertrain
between 2WD and 4WD.

There are two types of differential gear. The
difference between them is gear ratio.
2WD
ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm65.1 x 34.9
Outer bearing (O.D. x I.D.) mm50.0 x 21.4
4WD
<Bearings>
ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm73 x 45
Outer bearing (O.D. x I.D.) mm73 x 45
Drive shaftJoint typeOuter: B.J.
Inner: D.O.J.
Shaft length (joint to joint) mmRight: 318
Left: 291
Inner shaftO.D. x length mm31.5 x 304.2
Bearing (O.D. x I.D.) mm62 x 35

FRONT AXLE ± Service Specifications/Lubricants26-4
SERVICE SPECIFICATIONS26100030131
ItemStandard valueLimit
Front axle total backlash mm±11
Drive shaft axial play mm0.4 ± 0.7±
Solenoid valve resistance W36 ± 46±
Hub rotary sliding resistance N7 ± 26±
(Hub rotation starting torque) Nm0.5 ± 1.8±
Amount of movement of far the wheel bearing in an axial
direction mm0.05 or less±
Setting of D.O.J. boot length mm80 + 3±
Clutch gear play (bearing axial play) mm0.05 ± 0.30±
Drive gear backlash mm0.11 ± 0.16±
Differential gear backlash mm0 ± 0.076±
Drive pinion rotation torque NmWithout oil sealWhen replacing (with anti-rust agent)
0.3 ± 0.5±
When replacing or reusing (with gear oil
applied) 0.15 ± 0.25±
With oil sealWhen replacing (with anti-rust agent)
0.5 ± 0.7±
When replacing or reusing (with gear oil
applied) 0.3 ± 0.4±
Drive gear runout mm±0.05
Differential gear backlash mm±0.2
LUBRICANTS26100040141
ItemsSpecified lubricantsQuantity
Front differential gear oilHypoid gear oil API classification
GL-5 or higher SAE viscosity No. 90,
80W0.9

D.O.J. boot greaseRepair kit grease100 g

FRONT SUSPENSION ± Service Specifications/Sealant33A-3
SERVICE SPECIFICATIONS33200030088
ItemsStandard valueLimit
Toe-inAt the centre of tyre thread mm0 ± 7±
Toe-angle
(per wheel)
2WD0
± 0
19'±
(er wheel)
4WD
<Vehicles with
205/80 R16 tyre>0
± 0
16'±
4WD
<Vehicles with 31
x 10.50 R15 tyre>0
± 0
15'±
Camber0
10' ± 1
10' (Difference between
right and left within 30')±
Caster2WD1
45' ± 3
45' (Difference between
right and left within 30')±
4WD1
15' ± 3
15' (Difference between
right and left within 30')±
Kingpin inclination2WD15
00'±
4WD14
50'±
Shock absorber attaching dimension mm1 ± 2±
Upper arm ball joint starting torque Nm2WD0.8 ± 3.4±
Strut bar attaching dimension mm79±
Lower arm ball joint end play mm±0.5
Lower arm bush press-fitting force kN9.8±
Clearance between bump stopper and
bump stopper bracket mm4WD21 ± 23±
Stabilizer link assembly attaching
dimension mm4WD16 ± 18±
SEALANT33200050015
ItemSpecified sealant
Upper arm ball joint dust cover <2WD>3M ATD Part No. 8661 or equivalent

STEERING ± Service Specifications37A-3
SERVICE SPECIFICATIONS37100030021
ItemsStandard valueLimit
Steering wheel free play mmWith engine running±50
With engine stopped10 or less±
Steering angle2WDInner wheel33
55' ± 36
55'±
Outer wheel30
57'±
4WDInner wheel29
40' ± 32
40'±
Outer wheel29
30'
Steering gear backlash mm±0.5
Variation of tie rod end ball joint shaft direction mm±1.5
Tie rod end ball joint starting torque Nm3.0±
Steering gear oil level mm22±
Engine idle speed r/min4G6750 + 100±
4D56750 + 100±
Stationary steering effort N39.2 or less±
Oil pump
p
ressure MPa
Oil pump relief pressure8.3 ± 9.0±
ressure MPa
Pressure under no-load conditions0.8 ± 1.0±
Steering gear retention hydraulic pressure8.3 ± 9.0±
Oil pressure switch operating pressure MPaOFF
ON1.5 ± 2.0±
ON
OFF0.7 ± 1.2±
Mainshaft starting torque Nm0.49 ± 0.78±
Cross-shaft axial play mm0.05 or less±
Mainshaft total starting torque Nm<2WD>0.98 ± 1.47±
<4WD>0.69 ± 1.28±
Pitman arm ball joint starting torque Nm0.5 ± 1.5±
Mainshaft axial play mm0.03 or less±
Backlash between ball groove of rack piston and balls mm±0.05
Idler arm sliding resistance N2WD8.8 ± 30±
4WD2.4 ± 16±

2
SERIVICE SPECIFICATIONS
ItemsStandard value Limit
With engine running - 50Steering W heel free play mm
With engine stopped 10 or less -
Inner wheel 33°55’-36°55’ -2W D
Outer wheel 30°57’ -
Inner wheel 29°40’-32°40’ -
Steering angle
4W D
Outer wheel 29°30’
Steering gear backlash mm - 0.5
Variation of tie rod end ball joint shaft direction mm - 1.5
Tie rod end ball joint starting torque Nm 3.0 -
Steering gear oil level mm 22 -
4G6 750 ± 100 -Engine idle speed r/min
4D56 750 ± 100 -
Stationairy steering effort N 39.2 or less -
Oil pump relief pressure 8.3 - 9.0 -
Pressure under no-load conditions 0.8 - 1.0 -
Oil pump
pressure MPa
Steering gear retention hydraulic pressure 8.3 - 9.0 -
OFF →
ON 1.5 – 2.0 -Oil pressure switch operating pressure Mpa
ON →
OFF 0.7 – 1.2 -
Mainshaft starting torque Nm 0.49 – 0.78 -
Cross-shaft axial play mm 0.05 or less -
<2WD> 0.98 – 1.47 -Mainshaft total starting torque Nm
<4WD> 0.69 – 1.28 -
Pitman arm ball joint starting torque Nm 0.5 – 1.5 -
Mainshaft axial play mm 0.03 or less -
Backlash between ball groove of rack piston and balls mm - 0.05
2WD 8.8 – 30 -Idler arm sliding resistance N
4WD 2.4 – 16 -
STEERING – Service Specifications37A-3
37100030021
<Deleted>

13
Items Specifications
Pressure switch activation oil pressure
Mpa (kg/cm2, psi)
OFF
→ ON1.5 – 2.0 (15 – 20, 21-284)
ON
→ OFF0.7 – 1.2 (7.2 – 12, 100-171)
Mainshaft starting torque (Manual steering)
Nm (kgcm, in.lbs.) 0.35 – 0.55 (3.5 – 5.5, 3 – 5)
Mainshaft axial play (Power steering)mm (in.)0.03 – (0.0012) or less
Cross-shaft axial play mm (in.)
Manual steering’ 0.05 (0.0020)
Power steering 0.05 (0.0020)
Mainshaft total starting torque Nm (kgcm, in.lbs.)
Manual steering 0.65 – 0.85 (6.5 – 8.5, 5.7 – 7.3)
Power steering 0.45 – 1.25 (4.5 – 12, 5, 4 – 11)
Ball joint starting torque Nm (kgcm, in.lbs.)
Tie rod end 1 – 3 (10 – 30, 8.9 – 26)
Idler arm 0.5 – 2.0 (5 – 520, 4 – 17)
Idler arm turning torque Nm (kgcm, in.lbs.) 0.3 – 2.0 (3 – 20, 3 – 17)
Spring balance reading N (kg,lbs) 2.3 – 15.4 (0.23 – 1.54, 0.5 – 33.9)
Limit
Steering wheel free play mm (in.)
Manual steering 50 (1.97)
Power steering 50 (1.97)
Steering gear backlash mm (in.) 0.5 (0.020)
Ball joint axia play mm (in.) 1.5 (0.059)
Backlash between ball groove of rack piston
And balls mm (in.) 0.05 (0.0020)
Gap between vane and rotor groove mm (in.) 0.06 (0.0024)
Clearance between oil pump drive shaft
And pump body mm (in.) 0.1 (0.004)
STEERING – Specifications37-3
<Deleted>