display NISSAN 350Z 2005 Z33 Navigation Manual

Route calculation screen will be displayed.
The suggested route will be displayed with a
thick blue line. If you enter this route, the voice
guide will start.
INFO:

If you want to cancel the route calculation,
press the CANCEL button.

If you set a place which is not suitable as a
destination, the suggested route will not be
displayed. In such a case, the
OK key will be
displayed on the screen. Select the
OK key.
Reset a correct destination.
If route calculation is not possible with all the
set preferences, the system may look up a
route that does not exactly correspond to the
preferences.

When deleting the settings of destinations or
waypoints, press the ROUTE button.
Enlarged intersection displayThe enlarged map will be displayed during route
guidance, unless the Map button is pressed. If
the Map button is pressed after the route
guidance has been set, the display will switch to
the ordinary map, but when the vehicle ap-
proaches a guide point such as an intersection,
the enlarged map will automatically be dis-
played. Once you pass the guide point, the
display will return to the ordinary map.
INV1556
INV1557
How do I program a destination?
5-37


04.7.6/Z33-N


INFO:

When the Map button is pressed right
before the guide point, only the ordinary map
will be displayed for the guide point.

If route numbers are included in the map
data, route numbers will be displayed on the
left side of the screen.

If street names are displayed in two lines,
route numbers will not be displayed.NOTE:

When the guide point is close to the
guidance start point, the enlarged map
may not be displayed.

The guide point name may not be dis-
played.

The position of the vehicle icon on the
enlarged map may differ from the posi-
tion on the current display.
1. Press the MAP or PREVIOUS button.
The map screen will appear.
INFO:
To display the enlarged map, press the MAP
button or PREVIOUS button.
2. When the vehicle arrives at the neighborhood
of the destination, the route guidance will end
automatically.
INFO:

To alternate between the map and the en-
larged screen, press the MAP button or
PREVIOUS button.

In the map screen, the distance to the next
guide point and the turning direction will be
INV1558
INV1559
5-38
How do I program a destination?


04.7.6/Z33-N


displayed on the right side of the screen. Using the joystick, you canadjust the destina-
tion(waypoints).
1. Press the ROUTE button.
2. Select the
Edit Route key.
INV1560
ADJUSTINGAND DELETINGTHE
PRESET DESTINATION
(WAYPOINTS)
How do I program a destination?
5-39


04.7.6/Z33-N


3. Choose the destination (waypoints) you want
to adjust on the [EDIT ROUTE] screen.4. The map screen will be displayed for adjust-
ing. Use the joystick to adjust the location.
INFO:
When you move the joystick, the
Adjust key will
be displayed.5. Select the
Adjust key.
The new destination (waypoints) will be set.
INV1561
INV1562
INV1563
5-40
How do I program a destination?


04.7.6/Z33-N


The destination and waypoint can be deleted at
one time.
1. Press the ROUTE button.
Several keys will be displayed on the right of
the screen.
Select the
Edit Route key.2. The [EDIT ROUTE] screen will be displayed.
Select the
All Clear key.3. Select the
Yes key.
INV1560
INV1568
INV1569
ALL CLEAR5-42
How do I program a destination?


04.7.6/Z33-N


The system will display pre-defined POIs (Points
of Interest) in the current vicinity of the vehicle
and the distances to them. These POIs can be
gas stations, hotels, restaurants, ATM’s or
customer-programmed facilities. This function
will operate while the vehicle is moving.
1. Press the ROUTE button.
The display shows several keys on the right of
the screen.
Select the
Quick Stop key.2. The display shows the [QUICK STOP]
screen.
Select the category of your choice.
INFO:
Five categories are displayed on the screen. The
last one can be customized. When you use a
POI category frequently, it is convenient to use
the quick stop function. Please refer to “Quick
stop customer setting” on page 5-44.3. The cuisine selection screen is displayed only
when the
RESTAURANT key is selected.
Select theAll key or
Fast Food key.
INV1570
INV1571
INV1572
QUICK STOP
How do I program a destination?
5-43


04.7.6/Z33-N


4. The display shows the direction and distance
from the current vehicle position to the se-
lected facility.
Select the facility name you want to set as a
destination (waypoints).5. Set route priorities, then select the
OK key. Route calculation to the destina-
tion will be started.
INFO:
If quick stop is set after the destination was set,
the system starts the route calculation to the
location as the waypoint. Five waypoints can be
registered at the same time.
QUICK STOP CUSTOMER SETTING1. Press the SETTING button.
2. Select the
Navigation key on the [SET-
TINGS] screen.
INV1573
INV1574
INV1466
5-44
How do I program a destination?


04.7.6/Z33-N


3. Select the
Quick Stop Customer Settings
key on the [NAVIGATION SETTINGS]
screen.4. Select a facility you frequently visit. For ex-
ample, select the
NISSAN DEALER key.
When it is set, the screen returns to the
previous screen.
Press the MAP button to return to the map.5. Press the ROUTE button. Then, select the
Quick Stop key, and press the PUSH EN-
TER button. The display shows the selected
facility in the last row.
INV1576
INV1577
INV1578
How do I program a destination?
5-45


04.7.6/Z33-N


INFO:
When a hospital is set as a destination, a
telephone number of the destination will be
displayed, if available.This key is used to find the name of the street on
which the vehicle is currently located.
1. Press the ROUTE button.
Several keys appear on the right of the screen.
Select the
Where am I ? key.2. The display shows the [WHERE AM I ?]
screen, which includes the next, current, and
previous streets. Each one shows the streets
which the vehicle is approaching, currently
traveling on, and those streets the vehicle
was previously traveling on.
Press the MAP or PREVIOUS button to
return to the map.
INV1579
INV1580
INV1581
WHERE AM I ?
5-46
How do I program a destination?


04.7.6/Z33-N


6 How do I use the Point of Interest (POI)
feature?Setting with the
Point of Interest (POI) key ................. 6-2
Setting with the
List key .............................................. 6-2
Setting with theCategory key.................................... 6-5
Setting with theState key ........................................... 6-7
Setting with theCity key ........................................... 6-10
Setting with theNearby key ..................................... 6-12
POI categories ..................................................................... 6-14
Setting the nearby display icons ..................................... 6-15


04.7.6/Z33-N