NISSAN 350Z 2007 Z33 Body, Lock And Security System Workshop Manual

TRUNK LID
BL-111
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Removal and Installation of Trunk Lid Emergency Opener CableNIS0002I
REMOVAL
1. Remove trunk lid weatherstrip. Refer to BL-113, "Removal and Installation of Trunk Lid Weatherstrip" .
2. Remove trunk floor carpet, spare tire cover, trunk rear finisher, trunk front finisher, and trunk side box.
Refer to EI-49, "
TRUNK ROOM TRIM & TRUNK LID FINISHER" .
3. Remove floor box lid. Refer to EI-41, "
Removal and Installation (for Roadster Models)" .
4. Disconnect trunk lid emergency opener cable from trunk lid lock.
5. Disconnect each clamp of trunk lid emergency opener cable.
INSTALLATION
Install in the reverse order of removal.
1. Trunk lid lock assembly 2. Trunk lid emergency opener cable 3. Trunk lid emergency opener cable
hook
4. Trunk lid emergency opener lever
(secondary)5. Trunk lid emergency opener lever
holder6. Clip
7. Panel 8. Bolt 9. Nut
PIIB1490E

BL-112
TRUNK LID
Revision: 2006 November2007 350Z
Removal and Installation of Trunk Lid HingeNIS0002J
REMOVAL
1. Remove trunk lid stay. Refer to BL-109, "Removal and Installation of Trunk Lid Stay" .
2. Remove trunk lid assembly. Refer to BL-108, "
Removal and Installation of Trunk Lid Assembly" .
3. Remove trunk lid hinge mounting bolts, and then remove trunk
lid hinge.
INSTALLATION
1. Position trunk lid hinge to body side. Temporarily tighten front side bolt and rear side bolt in this order, and
then tighten them to the specified torque.
2. Install trunk lid to trunk lid hinge.
3. Install trunk lid stay.
CAUTION:

Before installing trunk lid hinge, apply anticorrosive agent onto the mounting surface of the vehi-
cle body.

After installation, perform trunk lid fitting adjustment. Refer to BL-107, "Fitting Adjustment" .

Check trunk lid open/close operation after installation.

Apply sealant and the same body color paint to trunk lid hinge and mounting bolts to cover broken
seal area.
Removal and Installation of Lift SpringNIS0002K
REMOVAL
Rotate lift spring bottom clockwise/counterclockwise by approxi-
mately 90 deg, and then remove lift spring.
INSTALLATION
Install in the reverse order of removal.
PIIB1181E
PIIB1180E

TRUNK LID
BL-113
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Removal and Installation of Trunk Lid WeatherstripNIS0002L
REMOVAL
Pull up and remove engagement with body from weatherstrip joint.
CAUTION:
After removal, do not pull strongly on the weatherstrip.
INSTALLATION
Install in the reverse order of removal.
1. Install the weatherstrip from the front with the vehicle center mark aligned to the weatherstrip mark.
2. At rear side, align the weatherstrip seam to the center of the striker.
3. After installing, pull the weatherstrip lightly to check for looseness.
CAUTION:
The weatherstrip should fit tightly onto the corners and trunk lid rear plate.
1. Storage lid 2. Trunk lid assembly 3. Trunk lid weatherstrip
4. Rear bumper fascia
PIIA7604E

BL-114
TRUNK LID OPENER
Revision: 2006 November2007 350Z
TRUNK LID OPENERPFP:84640
Component Parts and Harness Connector LocationNIS0002M
System DescriptionNIS0002N
Power is supplied at all times

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55

through 10A fuse [No.18, located in the fuse block (J/B)]

to BCM terminal 42.
Ground is supplied

to BCM terminal 52

through body grounds M30 and M66.
When trunk lid opener switch is ON (pushed) with trunk lid opener cancel switch is ON and driver's door
unlocked, ground is supplied

to BCM terminal 30

through trunk lid opener cancel switch terminals 1 and 2,

through trunk lid opener switch terminals 1 and 2,
PIIB9173E

TRUNK LID OPENER
BL-115
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z

through driver side door lock actuator (unlock sensor) terminals 2 and 4,

through grounds M30 and M66.
And power is supplied

to BCM terminal 68

through trunk lid lock assembly (trunk lid opener actuator) terminals 2 and 1

through grounds B5, B6 and T14.
Then trunk lid lock assembly (trunk lid opener actuator) opens trunk.
TRUNK LID OPENER CANCEL OPERATION
When trunk lid opener cancel switch is OFF (CANCEL), it cannot open trunk with trunk lid opener switch.
TRUNK OPENER OPERATION WITH KEY FOB
Open the trunk with key fob. Refer to BL-63, "Trunk Opener Operation/For Roadster" .

BL-116
TRUNK LID OPENER
Revision: 2006 November2007 350Z
Wiring Diagram—T/LID— NIS0002O
TIWT2267E

TRUNK LID OPENER
BL-117
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
TIWT2198E

BL-118
TRUNK LID OPENER
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCMNIS0002P
Te r -
minalWire
colorItemSignal input/
outputConditionVoltage (V)
(Approx.)
18 BRemote keyless entry
receiver (Ground)—— 0
19 YRemote keyless entry
receiver (Power supply)OutputKey is inserted in IGN key cylinder 0
All door closed
20 LRemote keyless entry
receiver (Signal)InputKey is inserted in IGN key cylinder 0
Waiting
(All door closed)
When signal is received
(All door closed)
30 P Trunk lid opener switch InputTrunk lid opener
cancel switch is
ONTrunk lid opener
switch is ON0
Trunk lid opener
switch is OFF5
Driver side door is
lockedTrunk lid opener
cancel switch is
OFF5
39 L CAN – H Input/Output — —
40 P CAN – L Input/Output — —
42 GY Ignition switch (ON) Input Ignition switch ON or START position Battery voltage
52 B Ground — — 0
55 RPower source (Fusible
link)Input — Battery voltage
68 L/RTrunk lid opener release
output signalOutput Closed (OFF) → Opened (ON) 0 → Battery voltage
OCC3881D
OCC3879D
OCC3880D

TRUNK LID OPENER
BL-119
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NIS0002Q
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
ACTIVE TEST
BCM diagnosis
partInspection item, self-diagnosis
modeContent
TrunkDATA MONITOR Displays the input data of BCM in real time basis.
ACTIVE TEST Give a drive signals to load to check the operation check.
Test item Content
TRUNK/BACK DOORThis test is able to check trunk lid opener actuator unlock operation. This actuator unlocks when “ON” on
CONSULT-III screen is touched.

BL-120
TRUNK LID OPENER
Revision: 2006 November2007 350Z
Trouble DiagnosisNIS0002R
TRUNK DOSE NOT OPEN WITH TRUNK LID OPENER SWITCH
1. CHECK TRUNK LID OPENER CANCEL SWITCH
Check trunk lid opener cancel switch position.
Ye s o r N o
Yes >> GO TO 2.
No >> Turn on trunk lid opener cancel switch.
2. CHECK TRUNK LID OPEN INPUT SIGNAL
1. Remove Key from ignition key cylinder.
2. Unlock driver side door.
3. Check voltage between BCM and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 6.
3. CHECK TRUNK LID OPEN OUTPUT SIGNAL
Check voltage between BCM and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace BCM. Refer to BCS-17, "
Removal and Installation of BCM" . Is trunk lid opener cancel switch in ON posi-
tion?
ConnectorTerminal
(Wire color)
ConditionVoltage (V)
(Approx.)
(+) (–)
M90 30 (P) GroundTrunk lid opener switch ON 0
Trunk lid opener switch OFF 5
PIIB9174E
ConnectorTerminal
(Wire color)
ConditionVoltage (V)
(Approx.)
(+) (–)
B83 68 (L/R) GroundTrunk lid opener switch
ONBattery voltage
Trunk lid opener switch
OFF0
PIIB1270E