NISSAN ALMERA 2001 Service Manual

Components-2 3AX00, 3AX01, 3AX19, 3AX63
and 3AX64 models
NJAT0233
SAT102K
OVERHAUL
Components-2 3AX00, 3AX01, 3AX19, 3AX63 and 3AX64 models
AT-359

Components-2 3AX10 and 3AX18 modelsNJAT0234
SAT936J
OVERHAUL
Components-2 3AX10 and 3AX18 models
AT-360

Components-3 3AX00, 3AX01, 3AX19, 3AX63
and 3AX64 models
NJAT0235
SAT061K
OVERHAUL
Components-3 3AX00, 3AX01, 3AX19, 3AX63 and 3AX64 models
AT-361

Components-3 3AX10 and 3AX18 modelsNJAT0236
SAT103K
OVERHAUL
Components-3 3AX10 and 3AX18 models
AT-362

Oil ChannelNJAT0118
SAT032K
OVERHAUL
Oil Channel
AT-363

Locations of Adjusting Shims, Needle
Bearings, Thrust Washers and Snap Rings Ð
3AX00, 01, 19, 63 and 64 models
NJAT0117
AAT416A
OVERHAUL
Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap Rings Ð 3AX00, 01, 19, 63 and 64 models
AT-364

Locations of Adjusting Shims, Needle
Bearings, Thrust Washers and Snap Rings Ð
3AX10 and 3AX18 models
NJAT0237
SAT067K
OVERHAUL
Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap Rings Ð 3AX10 and 3AX18 models
AT-365

NJAT0120
SAT049K
1. Drain ATF through drain plug.
SAT008D
2. Remove torque converter.
SAT009D
3. Check torque converter one-way clutch using check tool as
shown at left.
a. Insert check tool into the groove of bearing support built into
one-way clutch outer race.
b. While fixing bearing support with check tool, rotate one-way
clutch spline using flat-bladed screwdriver.
c. Check inner race rotates clockwise only. If not, replace torque
converter assembly.
SAT586H
4. Remove oil charging pipe and oil cooler tube.
DISASSEMBLY
AT-366

SAT023JB
5. Set manual shaft to ªPº position.
6. Remove PNP switch.
SAT128E
7. Remove oil pan and oil pan gasket.
+Do not reuse oil pan bolts.
8. Check foreign materials in oil pan to help determine cause of
malfunction. If the fluid is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indi-
cates varnish build up. Varnish can cause valves, servo, and
clutches to stick and may inhibit pump pressure.
+If frictional material is detected, replace radiator after
repair of A/T. Refer to LC-16, section ªRadiatorº.
9. Remove control valve assembly according to the following pro-
cedures.
AAT260A
a. Remove control valve assembly mounting bolts A, B and C.
DISASSEMBLY
AT-367

AAT262A
b. Remove stopper ring from terminal body.
c. Push terminal body into transmission case and draw out sole-
noid harness.
SAT017D
10. Remove manual valve from control valve assembly as a pre-
caution.
SAT877J
11. Remove return spring from servo release accumulator piston.
SAT019DA
12. Remove servo release accumulator piston with compressed
air.
13. Remove O-rings from servo release accumulator piston.
SAT020D
14. Remove N-D accumulator piston and return spring with com-
pressed air.
15. Remove O-rings from N-D accumulator piston.
DISASSEMBLY
AT-368