ESP NISSAN CUBE 2010 3.G Quick Reference Guide

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
LOCK DOORS
Press the
button to lock all doors.

UNLOCK DOORS
Press the
button once to unlock the driver’s door only.
Press the button again within 5 seconds to unlock all doors.
USING THE PANIC ALARM
Press and hold the
button for longer than 1 second.
The panic alarm will sound and the headlights will stay on
for 25 seconds. The panic alarm stops when it has run for
25 seconds or when any button is pressed on the keyfob.
2
NISSAN INTELLIGENT KEY™ (if so equipped)
The niSSA n intelligent key™ allows you to lock or unlock your vehicle, open
your back door and start the engine.
n OT e: it is important to make sure the intelligent key is with you (that is, in
your pocket or purse).

The operating range of the door and back door/unlock function is
approximately 31 in (80 cm).

Locking the vehicle - Push any door handle Request Switch
01 once.

unlocking the vehicle - Push any door handle
Request Switch

01 once. The corresponding door
will unlock. Push the door handle Request Switch


01 again within 5 seconds; all other doors will unlock.
STARTin
G THe enGine
depress the brake pedal.

Push the ignition switch START/STOP button to start
the engine.
TuRnin G THe en Gine Off
Move the shift lever to the P (PAR k) position and apply
the parking brake.

Push the ignition switch START/STOP button to turn
the engine off.
01

CHILD SAFETY REAR DOOR LOCKS
The child safety lock levers are located on the edge of the rear doors.

child safety locks help prevent the rear doors from being opened
accidentally, especially when small children are in the vehicle.

When the lever is in the LO ck position, the door can only be
opened from the outside.
FUEL-FILLER DOOR RELEASE
The fuel-filler door release is located on the lower left side of the instrument
panel next to the hood release.

To open the fuel-filler door, pull the release handle.

To lock, close the fuel-filler door securely.
TILT STEERING COLUMN
TiLT Ad Ju STM enT
Push the lock lever down
01 .

Move the steering wheel up or down and stop in the
desired position.

Pull up on the lock lever
01 to lock the steering wheel in
position.01
FRONT SEAT ADJUSTMENTS
Pull up on the lever
01 under the front of the seat
and slide forward or backward. Release the lever
to lock the seat in position.

Pull up on the lever
02 on the side of the seat to
adjust your seatback forward or backward. Release
the lever when you have found a comfortable angle
and the seat belt fits properly.
SeAT LifTe R (driver’s seat)
Pull up or push down on the adjusting lever
03
repeatedly to adjust the seat height.
01
0203

To increase or decrease the volume of the voice prompts, press the VOL (volume) control
switch

or
on the steering wheel or turn the POWER/VOLUME knob on the
audio system while the system is responding.

if the Voice Recognition system does not recognize your voice commands, train th\
e system
using the Speaker Adaptation Mode. See your Owner’s Manual for detailed information.

Some commands are not available while the vehicle is in motion.

The “Help” command can be used in any menu to hear a list of availa\
ble commands.

Please refer to the cellular phone manufacturer’s Owner’s Manual for detailed information
regarding your Bluetooth® phone.

For recommended phones and detailed instructions, please visit
www.nissanusa.com/bluetooth.
cOnnec TinG YOu R PHOne
To use the hands-free feature, you need to set up, or connect, the system to recognize your
compatible cellular phone(s). five compatible Bluetooth®-enabled phones can be connected.
After setup, the system automatically connects with a connected phone wh\
en the ignition is in the
A cc or O n position, as long as the phone is on and in the vehicle.
n OTe: Some cellular phones require the user to enable the automatic reconnec\
tion feature. Please
refer to the cellular phone manufacturer’s Owner’s Manual for Blue\
tooth
® setup information.
cOnnec TinG PROcedu Re
n OTe: The vehicle must be stationary when connecting the phone.
1. Press the

button on the steering wheel. The system announces the available commands.
2. Say “connect Phone.”
3. The system acknowledges the previous command and announces the next set of available
commands. Say “Add phone.”
4. initiate connecting from the phone.

The connecting procedure varies according to each cellular phone model. for detailed
connecting instructions and a list of compatible phones, please visit
www.nissanusa.com/bluetooth.

When prompted for a Passkey code, enter “1234” from the handset. (The Passkey code
is assigned by ni SSAn and cannot be changed.)
5. Say a name for the phone when the system asks you to provide one. You can give the phone
a name of your choice.
MAkin G A PHO ne c ALL
1. Press the
button.
2. After the tone, do one of the following:

Say “call.” After the system responds, say the name of the person in the phonebook.

Say “ call Phone number.” After waiting for the tone, say [number]. for example, say “ call
Phone number.” After waiting for the tone, say “123-456-7891.”

Say “Redial” to redial the previous phone number.

16
Say “ call Phone number.” After the system responds, say “Special number” to dial more
than 10 digits or special characters.

You can say all the digits of a 7- or 10-digit phone number at one time.

for a 10-digit number, saying the phone number in groups of 3, 3 and 4 digits may
improve recognition for some speakers. To use this group dialing method, say only the
first 3 digits of the phone number. After the system recognizes the number, it will request
the next 3 digits and finally the last 4 digits.

if a phone number is incorrectly recognized, you can try entering the pho\
ne number again
using the 3-3-4 group dialing procedure by saying “correction.”

When you have finished speaking the phone number wait for the system to repeat it back
to you, then say “dial.”
Recei Vin G/ endin G A PHO ne c ALL
When you receive a phone call, a ring tone sounds through the audio syste\
m.

To accept the call, press the
button. To reject the call, press the button.

To hang up the phone at the end of a call or to disconnect during call placement, press
the
button.
HOW TO SAY nu MBeRS
ni SSAn Voice Recognition permits numbers to be spoken in a variety of ways.

Say “zero” or “oh” for “0.” example: 1-800-662-6200 – Say “one eight zero zero six six two
six two oh oh.”

Say “pound” for “#.” Say “star” for “*” (available when using the “call Phone number” then
“Special number” command and the “Send” command during a call).

Say “plus” for “+” (available only when using the “ call Phone number” then “Special number”
command).

Say “pause” for a 2-second pause.
uSinG YOu R PHOneBOOk
When a compatible phone is connected to the system, the phonebook is automatically downloaded.
This allows you to access your phonebook from the Bluetooth® system to call contacts by name.
u p to 1,000 phone numbers will be transferred. To access your phonebook:
1. Press the

button and wait for the tone.
2. Say “Phonebook.”
3. Wait for the tone, then say [a name] or say “List names.” The name must be said exactly as it
is entered in your phonebook for the system to recognize it. for example, say “Phonebook”
then after the system responds, say “Michelle.”
The phonebook can transfer multiple numbers for each entry. if you select a name with multiple
numbers, the system will ask you which number you want to dial.