light NISSAN GT-R 2015 R35 Multi Function Display Owners Manual

1-4About Multi function display system
CONTROL PANEL
Navigation, Multi function meter
&1Monitor:
Multi function screens appear here.
&2<PHONE>:
Push to access the phone settings.
&3<SETTING>:
Push to access the system settings.
&4<INFO>:
Push to display the vehicle information and the
navigation information, such as GPS and version
information, etc.
&5<DEST>:
Push to enter a destination. Various methods for
entering a destination are available.
&6<ROUTE VOICE>:
Push to access guidance control functions
(guidance cancellation, route priority, waypoint
settings on the route, etc.) .
&7<MAP>:
Push to display the current location map screen.
&8<FUNCTION>:
Push to display the multi function meter screen.
&9<BACK>:
Push to return to the previous screen. In a
settings screen, this button can also be used to
apply the setting. In a character input screen, this
button can also delete the characters that have
been entered.
&10Center dial/<ENTER>:
Turn to highlight an item on the screen or adjust a
setting. Push to select the highlighted item on the
screen. Use the center dial to adjust the map
scale. If this button is pushed while a map is
displayed, the map menu screen is displayed.
&11<OFF> (DAY/NIGHT):
Push to switch between the day screen (bright)
and the night screen (dark) . Push and hold to turn
off the display. Push again to turn on the display.
&12<STATUS>:
Push to display the current status of the air
conditioner, radio, audio, vehicle information
(drivable distance and average fuel economy)
and navigation systems.
CONTROL BUTTONS AND
FUNCTIONS

1-10About Multi function display system
MENU SCREEN AND HOW TO OP-
ERATE
Menu screens and their purposes
Push<DEST>, <ROUTE VOICE>,
<PHONE>, <INFO>or<SETTING> to dis-
play the corresponding menu screen.
How to select a menu item:
Example: <DEST> screen
1. Turn the center dial clockwise or counter- clockwise. An item is highlighted accord-
ingly. 2. To select the preferred menu item, highlight
the item and push <ENTER>. The next
screen is displayed.
3. Push <BACK> to return to the previous
screen without applying any changes.
Push <MAP> to return to the current
location map screen without applying any
changes.
INFO:
Depending on the menu selected, pushing
<MAP> may not return you to the current
location map screen.
BASIC OPERATION

Using controls to adjust values, levels, etc.
There are two main methods you can use to
control the navigation system: the center dial or
the touch panel. Use these controls to adjust the
volume of phone and voice guidance, the display
brightness, etc.
How to adjust:
1. Highlight the preferred setting item andpush <ENTER>. The color of the corre-
sponding adjustment item changes. 2. Use the center dial or the touch panel, and
the value or bar indicating levels increases
or decreases accordingly.
3. Push <ENTER> or<BACK> to apply the
setting.
INFO:
. This same adjustment can also be made by
the touch panel operation.
“List screen” (page 1-12)
About Multi function display system1-11

1-12About Multi function display system
LIST SCREEN
After searching for a point of interest, a list
screen is displayed.
Depending on the list displayed, it can be
sorted.
Items displayed in list
*1Highlight the preferred item from the list and push
<ENTER>to select it. If a location or facility
name is not completely displayed (due to length) ,
highlight the item to display the hidden part of the
name.
*2Distance from the current location
*3Direction to the point of interest
*4If the entire list cannot be displayed on the
screen, the system displays the total number of
items in the list and the entry number of the
selected item. Turn the center dial to scroll the
list.
*5An item that starts with the selected letter will be
displayed at the top of the list.
*6Highlight and push <ENTER>to sort the list in
the original order.
*7When the list is sorted by the shortest distance,
the selected location can be confirmed in the preview displayed on the right side of the screen.
*8Highlight and push
<ENTER>to modify the
search conditions.

1-14About Multi function display system
CHARACTER (letters and numbers)
INPUT SCREEN
Alphanumeric characters are entered to set a
destination, search for a facility, edit stored
locations, etc.
1. Use the touch panel or center dial tohighlight a character on the displayed key-
board.
2. Push <ENTER>. The highlighted character
is entered.
3. Push <BACK>, or highlight [Delete] and
push <ENTER> to delete the last character
entered.
Push and hold <BACK>to delete all the
characters entered.
Highlight [Space] and push <ENTER>to
enter a space.
4. After finishing the entry, highlight [List] and push <ENTER>.
INFO:
.Push <BACK> on the control panel to
return to the previous screen, but only
after deleting all the characters entered.
.Touch [BACK] on the screen to return to the previous screen even when charac-
ters have been entered.
.The list screen appears automaticallywhen text has been entered and the
matching list items have been narrowed
down to a number that will fit on the
screen.
Symbol input screen
.Symbol keys are displayed by highlighting
[Symbols] and pushing <ENTER>. Al-
phabet keys are displayed by highlighting
[A-Z] and pushing <ENTER>.
HOW TO INPUT LETTERS AND
NUMBERS

NUMBER INPUT SCREEN
A phone number or a street number can also be
entered as a search method to look for a
destination. Perform the following procedure to
enter a number.
INFO:
Only the locations included in the map data
database can be searched for by a phone
number.
1. Use the touch panel or center dial to highlight a number on the displayed key-
board.
2. Push <ENTER>. The highlighted number is
entered.
3. Push <BACK>, or highlight [Delete] and
push <ENTER> to delete the last number
entered.
Push and hold <BACK>to delete all the
numbers entered.
4. After finishing the entry, highlight [List] and push <ENTER>.
INFO:
. Push <BACK> on the control panel to
return to the previous screen, but only after
deleting all the numbers entered.
. Touch [BACK] on the screen to return to the
previous screen even when numbers have
been entered.
About Multi function display system1-15

Example: The most detailed level (2D map)
Example: The widest level (2D map)
Example: The most detailed level (BirdviewTMmap)
Example: The widest level (BirdviewTMmap)
INFO:
The traffic information icons are not displayed on
the map screen when the map scale is set to 32
miles (64 km) or higher.
“Traffic information display and scale le-
vels” (page 6-11)
CHANGING MAP VIEW
The map view can be changed between the 2D
and BirdviewTMmaps. The map can also be
displayed in the split screen mode.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.
Navigation2-11

2-12Navigation
3. Highlight [Change View] and push<ENTER>.
4. Highlight the preferred map view and push <ENTER>. The indicator of the selected
map view illuminates.
5. The display automatically returns to the map screen.
Available views
. [2D Map]:
Switches to the 2D map.
. [Birdview (3D)]:
Switches to the Birdview
TMmap.
. [Split: 2D Map]:
Changes to the split screen mode and both
halves display maps in 2D.
. [Split: Birdview Map]:
Changes to the split screen mode and the
left half displays the map in 2D and the right
half displays the map in Birdview
TM.
INFO:
. When the split screen mode is selected, the
map settings for the left screen can be
changed independently.
“Setting left screen display”
(page 2-16)
. If the split screen mode is selected, the
normal map scrolling and scale adjustment
are set in the right screen. However, if an
icon is touched before adjusting the map
direction or scale, then each screen can be
adjusted independently.
Split: 2D Map
Split: BirdviewTMMap
Other settings
The map view can also be set by performing the
following procedure.
1. Push <SETTING>.
2. Highlight [Navigation] and push <ENTER>.
3. Highlight [Map View] and push <ENTER>.
4. Highlight [Change View] and push <ENTER>.

5. Highlight the preferred item and push<ENTER>.
Setting by voice command
1. Push <
>located on the steering wheel.
2. After the tone sounds, speak a command.
. To display the 2D map:
“Plan View map” (Alternate Command
Mode)
. To display the Birdview
TMmap:
“Birdview map” (Alternate Command Mode)
MAP VIEW SETTINGS
Other settings are also available for the map
screen, such as changing the map direction,
map color, Birdview
TMangle, etc.
Basic operation
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.
3. Highlight [Map Settings] and push
<ENTER>.
4. Highlight the preferred item and push<ENTER>.
Available setting items
. [Map Orientation]:
Sets the map direction to North Up or
Heading Up.
“Setting map orientation” (page 2-14)
Navigation2-13

2-14Navigation
.[Long Range]:
Sets the long range map view display on/off.
“Settings long range map view”
(page 2-15)
. [Map Color]:
Changes the map color.
“Setting map color ” (page 2-15)
. [Birdview Angle]:
Changes the Birdview
TMangle.“Changing BirdviewTMangle”
(page 2-16)
. [Left Split Map Settings]:
Sets the map settings for the left screen of
the split map.
“Setting left screen display”
(page 2-16)
. [Show all Freeway Exits on Route]/[Auto.
Show Turn List on Freeway]:
Sets the display of the freeway exit informa-
tion on/off.
“Show exit information on freeways”
(page 2-51)
Other settings:
The orientation of the map can also be set by
performing the following procedure.
1. Push <SETTING>.
2. Highlight [Navigation] and push <ENTER>.
3. Highlight [Map View] and push <ENTER>.
Setting map orientation
The map direction (orientation) can also be
changed in the 2D map. These settings are
available only in the 2D map or 2D/2D split map.
1. Highlight [Map Orientation] and push
<ENTER>.
2. Highlight the preferred map orientation andpush <ENTER>. The indicator of the
selected map orientation illuminates.
3. Push <MAP>to return to the current
location map screen.
Available map orientations
. [North Up]:
The top of the map remains oriented to the
north.
. [Heading Up]:
The top of the map follows the traveling
direction.