key NISSAN MAXIMA 2003 A33 / 5.G Navigation Manual

2. Select theRoute Info key .
3. Select the
T urn List key .A list of destinations, waypoints and guide
points will be displayed. Guidance will be
made at each guide point about which direction
to turn.
The distance between the guide points and the
required time will also be displayed.
It may take time to prepare the turn list. In such
cases, the
T urn List key will be highlighted
and you can not select it until calculation is
completed.
INFO:

In the turn list, turning points more than 60
miles (100 km) away from the current ve-
hicle location will not be displayed.

When calculated routes include a freeway ,
information about freeway entrances and
exits will also be displayed.
REQUESTING THE SIMULA-
TION DRIVE TO THE DESTI-
NA TION
Y ou can simulate driving the entire suggested
route to the destination on the screen.
1. T ouch the screen.
Keys will be displayed on the screen.
2. Select the
Route Info key .
INV0440
INV0441
INV0437
HOW DO I ADJUST THE DISPLAY?
11-10

3. Select theRoute Simulation key .
The screen will display a simulated drive withvoice guidance on the suggested route to the
destination.
4. Press the MAP button to go back to the
map display .
INFO:
If you select the
Pause key , simulation is in-
terrupted. If you select the key again, the simu-
lation will restart.
DISPLAYING THE TRACK
Y ou can have the system track the road you
have taken, and display it with indication mark
().
1. Change to the current vehicle location
screen.
2. Select the
Setting key .3. Select the
System Setting key on the
[SETTINGS] screen.
INV0442
INV0443
INV0259
HOW DO I ADJUST THE DISPLAY?
11-11

4. Select theT racking key .
5. Select the
On key .6. Press the MAP button.
The location of the vehicle will be displayed.
INFO:

Y ou can select the
On key to display the
indicator (), and the
Off key to get rid
of it.

The locus indicator () may be spaced dif-
ferently , according to the scale of the map.

If you re-set the current vehicle location, the
indicator () will be cleared.
GPS INFORMA TION DIS-
PLA Y
The following GPS information will be dis-
played on the screen: latitude, longitude, alti-
tude, signal reception, and satellite locations.
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
3. Select the
System Setting key on the
[SETTINGS] screen.
INV0444
INV0445
INV0446
INV0259
HOW DO I ADJUST THE DISPLAY?
11-12

4. Select theGPS Information key .
GPS information will be displayed.INFO:

The satellite with a strong enough signal
will be indicated in green.

The display will read, [3-dimensional po-
sitioning], [2-dimensional positioning], or
[positioning impossible], depending on the
signal strength. (Altitude will not be dis-
played in 2-dimensional positioning.)

When the MAP button is pressed, the
[CURRENT LOCA TION] screen will appear .
When the
Previous key is touched, the[SYSTEM SETTING] screen will appear .
UPDATING THE CURRENT VE-
HICLE LOCATION AND THE
DIRECTION
If the vehicle icon does not indicate the correct
location or the direction does not match the ac-
tual road, you can adjust them on the map
screen.
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
INV0447INV0448
HOW DO I ADJUST THE DISPLAY?
11-13

3. Select theSystem Setting key on the
[SETTINGS] screen.4. Select theAdjust Current Location key
on the [SYSTEM SETTINGS] screen.5. Align the correct location to the cross point
on the map using the joystick, and select
the
Set key . The current location will be
corrected, and the direction adjustment
screen will appear .
INV0259INV0449INV0450
HOW DO I ADJUST THE DISPLAY?
11-14

6. Adjust the direction using theand
key .
The arrow on the display shows the direction
of the vehicle icon.
7. Select the
Set key .INFO:

It is not possible to update the vehicle lo-
cation when the vehicle is moving.

Depending on the driving conditions, the
vehicle icon may not exactly correspond to
the actual location of the vehicle. T o verify
position, refer to map books or check actual
landmarks.

If you notice that the system is displaying
a different road from the one the vehicle is
actually traveling, and the vehicle icon doesnot go back to the right road after traveling
approximately 6-1/4 miles (10 km), update
the vehicle location.
CHANGING THE DISPLA Y
MODE
Y ou can split the screen into two sections to
display the map and A/C setting at the same
time.
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
INV0451INV0452
HOW DO I ADJUST THE DISPLAY?
11-15

3. Select theSystem Setting key on the
[SETTINGS] screen.4. Select theMap & A/C key .
5. Select the
On key .6. After setting, press the MAP button.
The right section displays the air conditioner
control screen and the left section displays the
map.
When the enlarged view is displayed, the air
conditioner control screen will not be dis-
played.
CHANGING THE DISPLA Y
COLOR
Y ou can change the display color .
INV0259INV0453
INV0464
INV0504
HOW DO I ADJUST THE DISPLAY?
11-16

1. Change to the current vehicle location
screen.
2. Select the
Setting key .
The display shows the [SETTINGS] screen.
3. Select the
System Setting key .
The display shows the [SYSTEM SETTINGS]
screen.4. Select the
Display Setting key .
The display shows the [DISPLA Y SETTING]
screen.
5. Select the
Background key .
When pressed, the display color is changed.6. T ouch the
Previous key .
The [SYSTEM SETTINGS] will be displayed.
The D/N button is used to change the display
color the same way as the
Background key .INV0259
INV0456INV0457
HOW DO I ADJUST THE DISPLAY?
11-17

ADJUSTING THE DISPLA Y
BRIGHTNESS
Y ou can choose the best brightness for the dis-
play .
INFO:

Y ou can have two different brightness set-
tings for the display . One setting for when
the headlights are on and the other setting
when headlights are off.

When the headlights are turned on, the
original factory (brightness) display setting
will adjust to the brightness suitable for
night (dim screen).
1. Change to the current vehicle location
screen.
2. Select the
Setting key .3. Select the
System Setting key .
The display shows the [SYSTEM SETTINGS]
screen.4. Select theDisplay Setting key .
The display shows the [DISPLA Y SETTING]
screen.
INV0259INV0456
HOW DO I ADJUST THE DISPLAY?
11-18

5. T ouch the Darker/Brighter key to adjust the
contrast.
6. T ouch the
Previous key .
The screen returns to the [SYSTEM SETTINGS]
screen.
SETTING AUTOMA TIC BEEP
SOUND
Y ou can set the automatic beep sound. (Acti-
vated during automatic rerouting, etc.)
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
3. Select the
System Setting key on the
[SETTINGS] screen.4. Select the
Beep on/off key .
The display shows the [BEEP ON/OFF] screen.
INV0458
INV0259
INV0459
HOW DO I ADJUST THE DISPLAY?
11-19