Oil NISSAN TEANA 2003 Service Manual

GI-8
PRECAUTIONS

Precautions for Engine OilsBAS0008H
Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin contact
with used oil.
If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
HEALTH PROTECTION PRECAUTIONS

Avoid prolonged and repeated contact with oils, particularly used engine oils.

Wear protective clothing, including impervious gloves where practicable.

Do not put oily rags in pockets.

Avoid contaminating clothes, particularly underpants, with oil.

Heavily soiled clothing and oil-impregnated footwear should not be worn. Overalls must be cleaned regu-
larly.

First aid treatment should be obtained immediately for open cuts and wounds.

Use barrier creams, applying them before each work period, to help the removal of oil from the skin.

Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help). Prepa-
rations containing lanolin replace the natural skin oils which have been removed.

Do not use gasoline, kerosene, diesel fuel, gas oil, thinners or solvents for cleaning skin.

If skin disorders develop, obtain medical advice without delay.

Where practical, degrease components prior to handling.

Where there is a risk of eye contact, eye protection should be worn, for example, chemical goggles or face
shields; in addition an eye wash facility should be provided.
Precautions for Air Conditioning BAS0008I
Use an approved refrigerant recovery unit any time the air conditioning system must be discharged. Refer to
ATC/MTC section “HFC-134a (R-134a) Service Procedure”, “REFRIGERANT LINES” for specific instructions.

GI-32
SERVICE INFORMATION FOR ELECTRICAL INCIDENT


Do not apply excessive shock to the control unit by dropping or
hitting it.

Be careful to prevent condensation in the control unit due to
rapid temperature changes and do not let water or rain get on it.
If water is found in the control unit, dry it fully and then install it in
the vehicle.

Be careful not to let oil to get on the control unit connector.

Avoid cleaning the control unit with volatile oil.

Do not disassemble the control unit, and do not remove the
upper and lower covers.

When using a DMM, be careful not to let test probes get close to
each other to prevent the power transistor in the control unit
from damaging battery voltage because of short circuiting.

When checking input and output signals of the control unit, use
the specified check adapter.
SAIA0255E
SEF348N

LIFTING POINT
GI-37
C
D
E
F
G
H
I
J
K
L
MB
GI

LIFTING POINTPFP:00000
Commercial Service Tools BAS0007R
CAUTION:

Every time the vehicle is lifted up, maintain the complete vehicle curb condition.

Since the vehicle's center of gravity changes when removing main parts on the front side (engine,
transmission, suspension etc.), support a jack up point on the rear side garage jack with a mission
jack or equivalent.

Since the vehicle's center of gravity changes when removing main parts on the rear side (rear axle,
suspension, etc.), support a jack up point on the front side garage jack with a mission jack or
equivalent.

Be careful not to smash or do not do anything that would affect piping parts.
Garage Jack and Safety Stand and 2-Pole LiftBAS0007S
WARNING:

Park the vehicle on a level surface when using the jack. Make sure to avoid damaging pipes,
tubes, etc. under the vehicle.

Never get under the vehicle while it is supported only by the jack. Always use safety stands when
you have to get under the vehicle.

Place wheel chocks at both front and back of the wheels on the ground.

When lifting the vehicle, open the lift arms as wide as possible and ensure that the front and rear
of the vehicle are well balanced.

When setting the lift arm, do not allow the arm to contact the brake tubes, brake cable, fuel lines
and sill spoiler.
Tool name Description
Board on attachment
Safety stand attachment
S-NT001
S-NT002

TOW TRUCK TOWING
GI-39
C
D
E
F
G
H
I
J
K
L
MB
GI

TOW TRUCK TOWINGPFP:00000
Tow Truck TowingBAS0007V
CAUTION:

All applicable local laws regarding the towing operation
must be obeyed.

It is necessary to use proper towing equipment to avoid
possible damage to the vehicle during towing operation.
Towing is in accordance with Towing Procedure Manual at
dealer.

Always attach safety chains before towing.

When towing, make sure that the transmission, steering
system and power train are in good order. If any unit is
damaged, dollies must be used.
NISSAN recommends that the vehicle be towed with the driving
(front) wheels off the ground as illustrated.
TOWING AN AUTOMATIC TRANSAXLE MODEL WITH THE FRONT WHEELS ON THE GROUND
CAUTION:
Never tow an automatic transaxle model with the front wheels on the ground as this will cause serious
and expensive damage to the transaxle.
Vehicle Recovery (Freeing a Stuck Vehicle) BAS0007W

Always pull the cable straight out from the front or rear of the
vehicle. Never pull on the vehicle at an angle.

Remove the front spoiler when you pull the vehicle forward. Oth-
erwise, the towing device may damage the spoiler.

Pulling devices such as ropes or canvas straps are not recom-
mended for use in vehicle towing or recovery.

Use the recovery hooks only, not other parts of the vehicle. Oth-
erwise, the vehicle body will be damaged.

Use the recovery hooks only to free a vehicle stuck in sand,
snow, mud, etc. Never tow the vehicle for a long distance using
only the recovery hooks.

The recovery hooks are under tremendous force when used to
free a stuck vehicle.

Stand clear of a stuck vehicle.
SGI805
PAIA0251E
PAIA0252E

GW-72
REAR WINDOW DEFOGGER

Check Filament BIS0010E
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2. Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3. If a filament is burned out, circuit tester shows 0 or battery volt-
age.
4. To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament RepairBIS0010F
REPAIR EQUIPMENT

Conductive silver composition (Dupont No. 4817 or equivalent)

Ruler 30 cm (11.8 in) long

Drawing pen

Heat gun

Alcohol

Cloth
SEL122R
SEL263
SEL265

IDX-2
ALPHABETICAL INDEX
Numerics
3rd position switch ............................. AT-161
, AT-210
A
A/C air flow ...................................................... ATC-31
A/C component layout ..................................... ATC-20
A/C compressor clutch removal and installation ...........
ATC-136
A/C compressor mounting ............................. ATC-134
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-15
A/C control operation (auto A/C) ...................... ATC-29
A/C diagnostic work flow (auto A/C) ................ ATC-94
A/C evaporator ............................................... ATC-144
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure .......
ATC-131
A/C HFC134a (R134a) system service tools ... ATC-16
A/C HFC134a system service equipment precaution ...
ATC-12
A/C lubricant (R134a) ...................................... ATC-21
A/C lubrication oil ........................................... ATC-150
A/C operational check ...................................... ATC-54
A/C self-diagnoses (auto A/C) .......... ATC-46, ATC-94
A/C service data specification ........................ ATC-150
A/C system description (auto A/C) ................... ATC-24
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-14, MA-35
A/T fluid replacement ............................. AT-15, MA-36
A/T IND - Wiring diagram .................................... DI-48
A/T shift control system ................................... AT-213
A/T shift lock system ........................................ AT-216
A/T shift lock system - Wiring diagram ............ AT-217
A/T trouble diagnoses ........................................ AT-34
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-251,
EC-258
, EC-272, EC-631, EC-638, EC-652
Accelerator pedal released position learning .... EC-47,
EC-389
AFS ..................................................................... LT-75
AFS - Wiring diagram ......................................... LT-79
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-48
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(QR20DE) .................... EM-17
Air cleaner and air duct(VQ23DE and VQ35DE) ..........
EM-131
Air cleaner filter replacement(QR20DE) ........... MA-20
Air cleaner filter replacement(VQ23DE and VQ35DE) .
MA-30
Air cleaner filter(QR20DE) ................................ EM-17
Air cleaner filter(VQ23DE and VQ35DE) ........ EM-132
Air conditioner cut control .................... EC-25, EC-362
Air flow meter - See Mass air flow sensor ...... EC-124,
EC-466
Air mix. door motor ......................... ATC-66, ATC-124
Ambient sensor ............................... ATC-96, ATC-109
Angular tightening application(QR20DE) ............ EM-6
Angular tightening application(VQ23DE and VQ35DE)
EM-120
Antenna ............................................................. AV-38
APPS1 - Wiring diagram ................... EC-253, EC-633
APPS2 - Wiring diagram ................... EC-260, EC-640
APPS3 - Wiring diagram ................... EC-274, EC-654
ASC/BS - Wiring diagram ................................ EC-605
ASC/SW - Wiring diagram ............................... EC-597
ASCBOF - Wiring diagram ............................... EC-661
ASCD ............................................................... EC-363
ASCD (automatic speed control device) ........... ACS-2
ASCD brake switch ........................... EC-602, EC-660
ASCD indicator lamp ....................................... EC-667
ASCD steering switch ...................................... EC-595
ASCIND - Wiring diagram ................................ EC-668
AT indicator lamp ................................................ DI-48
Audio ........................................................ AV-4, AV-18
AUDIO - Wiring diagram .......................... AV-7, AV-21
Auto air conditioner - Wiring diagram ............. ATC-39
Auto amp ...................................................... ATC-108
Auto anti-dazzling inside mirror ....................... GW-80
Automatic amplifier ........... ATC-44, ATC-56, ATC-108
AV communication line .......................... AV-49, AV-73
Axle ................................................................... MA-42
B
BA/FTS - Wiring diagram ................................. AT-111
BACK/L - Wiring diagram ................................. LT-193
Back-up lamp ................................................... LT-193
Basic inspection .................................. EC-40, EC-381
Battery ................................................................. SC-4
BCM (Body control module) .............................. BCS-3
Blower motor ................................... ATC-72, ATC-115
Blower unit .................................................... ATC-113
Boring/horning cylinder block(QR20DE) ......... EM-104
Boring/horning cylinder block(VQ23DE and VQ35DE) .
EM-250
Brake fluid level ................................................ MA-40
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-41
Brake lines and cables inspection .................... MA-40
Brake pedal .......................................................... BR-6
Brake switch ......... EC-245, EC-602, EC-626, EC-660
BRK/SW - Wiring diagram ................ EC-247, EC-627
Bulb specifications ........................................... LT-261
Bumper, front ...................................................... EI-14
Bumper, rear ....................................................... EI-17
C
Camshaft inspection(QR20DE) ........................ EM-44
Camshaft inspection(VQ23DE and VQ35DE) EM-194
Camshaft position sensor (PHASE) .. EC-176, EC-524
Camshaft(QR20DE) .......................................... EM-41
Camshaft(VQ23DE and VQ35DE) .................. EM-192
CAN - Wiring diagram ......... EC-114, EC-459, AT-134,
CVT-54

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
CAN (Controller Area Network) . BL-23, BL-48, BL-77,
GW-56
, SE-16
CAN communication EC-113, EC-458, AT-27, CVT-19,
CVT-53
, BL-23, BL-48, BL-77, GW-56, SE-16, WW-9
Canister-See EVAP canister ............... EC-29, EC-369
CHARGE - Wiring diagram ................................ SC-28
Charging system ................................................ SC-27
Chassis and body maintenance ........................ MA-35
CHIME - Wiring diagram ..................................... DI-60
CIGAR - Wiring diagram .................................. WW-60
Cigarette lighter ............................................... WW-60
Circuit breaker ................................................... PG-16
Closed loop control .............................. EC-22, EC-359
Collision diagnosis ........................................... SRS-55
Combination meter ............................................... DI-4
COMM - Wiring diagram ........................ AV-49, AV-73
Component Location (auto A/C) ...................... ATC-36
Compression pressure(QR20DE) ...................... EM-65
Compression pressure(VQ23DE and VQ35DE) ...........
EM-210
Compressor clutch removal and installation .. ATC-136
Compressor special service tool ...................... ATC-15
Condenser ..................................................... ATC-142
Connecting rod bearing clearance(QR20DE) .. EM-105
Connecting rod bearing clearance(VQ23DE and
VQ35DE) ......................................................... EM-251
Connecting rod bushing clearance(QR20DE) . EM-101
Connecting rod bushing clearance(VQ23DE and
VQ35DE) ......................................................... EM-247
Connecting rod(QR20DE) ............................... EM-101
Connecting rod(VQ23DE and VQ35DE) ......... EM-247
CONSULT-II for engine ....................... EC-80, EC-425
CONSULT-II Reference value (CVT) .............. CVT-43
Control units (terminal arrangement) ................. PG-74
Control valve (CVT) ......................................... CVT-23
Controller Area Network (CAN) . BL-23, BL-48, BL-77,
GW-56
, SE-16
Converter housing installation ............ AT-244, AT-355
COOL/F - Wiring diagram .................. EC-222, EC-579
Coolant mixture ratio ......................................... MA-15
Coolant replacement(QR20DE) ......................... MA-16
Coolant replacementVQ35DE ........................... MA-25
Cooling circuit (engine)(QR20DE) ....................... CO-8
Cooling circuit (engine)(VQ32DE and VQ35DE) CO-32
Cooling fan control ........................................... EC-575
Cooling fan motor ............................................ EC-575
Cooling fan relay .............................................. EC-575
Cooling fan(QR20DE) ........................................ CO-20
Cooling fan(VQ23DE and VQ35DE) .................. CO-44
Cowl top ............................................................... EI-21
Cowl top cover ..................................................... EI-21
Crankcase ventilation system - See Positive crankcase
ventilation ............................................ EC-30
, EC-370
Crankshaft position sensor (POS) ..... EC-169, EC-517
Crankshaft(QR20DE) ...................................... EM-104
Crankshaft(VQ23DE and VQ35DE) ................ EM-251
Crash zone sensor .......................................... SRS-44
CVT air breather hose ................................... CVT-186
CVT control system ......................................... CVT-16
CVT cross-sectional view ................................ CVT-15
CVT Electrical parts location ............................ CVT-30
CVT fluid checking ................ CVT-13, CVT-32, MA-36
CVT Fluid Cooler ........................................... CVT-189
CVT fluid replacement ........................ CVT-14, MA-38
CVT fluid temparature sensor .......................... CVT-69
CVT hydraulic control system .......................... CVT-17
CVT indicator ...................................................... DI-52
CVT self-diagnoses ......................................... CVT-47
CVT shift lock system .................................... CVT-180
CVT trouble diagnoses .................................... CVT-24
CVTIND - Wiring diagram ................................... DI-52
Cylinder block boring(QR20DE) ..................... EM-104
Cylinder block(QR20DE) .................................. EM-81
Cylinder block(VQ23DE and VQ35DE) .......... EM-228
Cylinder head bolt tightening(QR20DE) ........... EM-68
Cylinder head bolt tightening(VQ23DE and VQ35DE) .
EM-213
Cylinder head(QR20DE) ................................... EM-65
Cylinder head(VQ23DE and VQ35DE) ........... EM-210
D
D/LOCK - Wiring diagram .................................. BL-25
Diagnosis sensor unit ..................................... SRS-47
Diagnostic trouble code (DTC) for OBD system EC-10,
EC-34
, EC-347, EC-375
Diagnostic trouble code (DTC) inspection priority chart
EC-58
, EC-400, CVT-24
Differentil side oil seal .................................... CVT-187
Display and amp.assembly ............... ATC-44, ATC-56
Display Control Unit ........................................... AV-61
Display Unit ........................................................ AV-41
Door glass ........................................... GW-46, GW-50
Door glass Fitting Adjustment(Front) ................ GW-49
Door glass Fitting Adjustment(Rear) ................. GW-53
Door lock .......................................................... BL-123
Door mirror .......................................... GW-74, GW-77
Door trim ............................................................. EI-35
Door, front ........................................... BL-119, GW-46
Door, rear ............................................ BL-119, GW-50
Drive belt inspection(QR20DE) ......................... MA-16
Drive belt inspection(VQ23DE and VQ35DE) ... MA-24
Drive belt(QR20DE) .......................................... EM-14
Drive belt(VQ23DE and VQ35DE) .................. EM-128
Drive shaft ......................................................... MA-43
Driver air bag .................................................. SRS-35
Dropping resistor (A/T) .................................... AT-132
Duct and grilles .............................................. ATC-126
E
ECM input/output signal ....................... EC-72
, EC-415
ECM power supply EC-106, EC-193, EC-451, EC-541
ECM/PW - Wiring diagram ................. EC-194, EC-542
ECTS - Wiring diagram ...................... EC-133, EC-476
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-197, EC-200,
EC-213
, EC-552, EC-555

IDX-4
ALPHABETICAL INDEX
Electric throttle control actuator (VQ23DE and VQ35DE)
EM-137
Electrical load signal circuit ................ EC-280, EC-670
Electrical unit ..................................................... PG-74
Electrical units location ...................................... PG-67
Electronic ignition (EI) system ............. EC-23, EC-360
EMNT - Wiring diagram ................................... EC-673
ENG SS - Wiring diagram ................................ AT-117
Engine control circuit diagram ............. EC-70, EC-413
Engine control component parts location .......... EC-64,
EC-406
Engine control module (ECM) ............ EC-190, EC-538
Engine control system diagram and chart ........ EC-20,
EC-357
Engine coolant temperature sensor (ECTS) ... EC-131,
EC-474
Engine coolant(QR20DE) ................................. CO-10
Engine coolant(VQ23DE and VQ35DE) ........... CO-34
Engine fail-safe system ........................ EC-59, EC-401
Engine mounting control (Front) ...................... EC-672
Engine oil filter replacement(QR20DE) ............. MA-21
Engine oil filter replacement(VQ23DE and VQ35DE) ...
MA-31
Engine oil precautions .......................................... GI-8
Engine oil replacement(QR20DE) .................... MA-20
Engine oil replacementVQ23DE and VQ35DE . MA-30
Engine oil(QR20DE) ............................................ LU-7
Engine oil(VQ23DE and VQ35DE) .................... LU-19
Engine removal(QR20DE) ................................ EM-77
Engine removal(VQ23DE and VQ35DE) ........ EM-223
Engine trouble diagnoses ................................ EC-394
ETC1 - Wiring diagram ...................... EC-201, EC-556
ETC2 - Wiring diagram ...................... EC-209, EC-564
ETC3 - Wiring diagram ...................... EC-214, EC-569
EVAP canister ...................................... EC-29, EC-369
EVAP canister purge volume control solenoid valve ....
EC-282
, EC-677
EVAP vapor lines inspection ............................. MA-23
EVAP vapor lines inspection(VQ23DE and VQ35DE) ..
MA-34
EVAP vapor lines inspectionVQ23DE and VQ35DE ....
MA-33
Evaporative emission (EVAP) system . EC-27, EC-366
Evaporator ..................................................... ATC-144
Exhaust manifold(QR20DE) ............................. EM-23
Exhaust manifold(VQ23DE and VQ35DE) ..... EM-140
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-35
Expansion valve ............................................. ATC-145
F
F/FOG - Wiring diagram ................................... LT-129
F/LID - Wiring diagram ....................................... BL-45
F/PUMP - Wiring diagram .................. EC-296, EC-691
Floor trim ............................................................. EI-52
Flow charts ......................................................... GI-24
Fluid temparature sensor (CVT) ...................... CVT-69
Fluids ................................................................ MA-14
Fluorescent leak detector ............................. ATC-146
Fog lamp, front ................................................. LT-126
Freeze frame data .............................. EC-35, EC-376
FRO2 - Wiring diagram ..................... EC-302, EC-309
FRO2B1 - Wiring diagram ................ EC-697, EC-707
FRO2B2 - Wiring diagram ................ EC-699, EC-709
Front bumper ...................................................... EI-14
Front door ............................. BL-119, BL-123, GW-46
Front fog lamp .................................................. LT-126
Front passenger air bag .................................. SRS-39
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-46
Front side air bag ............................................ SRS-40
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ...................................... CVT-70
Fuel cut control (at no load high engine speed) EC-24,
EC-361
Fuel gauge ............................................................ DI-4
Fuel injector and fuel tube(QR20DE) ................ EM-34
Fuel injector and fuel tube(VQ23DE and VQ35DE) ......
EM-155
Fuel lid opener, electric ...................................... BL-44
Fuel line inspection .............................................. FL-3
Fuel line inspection(QR20DE) .......................... MA-20
Fuel line inspectionVQ23DE and VQ35DE ....... MA-30
Fuel pressure check ........................... EC-49, EC-392
Fuel pressure release ......................... EC-49, EC-392
Fuel pump ......................................... EC-295, EC-690
Fuel pump and gauge .......................................... FL-4
Fuel system ......................................................... FL-3
Fuel tank .............................................................. FL-8
Fuel tank vacuum relief valve ............. EC-29, EC-369
Fuse .................................................................. PG-16
Fuse and fusible link box .................................. PG-80
Fusible link ........................................................ PG-16
G
Gauges ................................................................. DI-4
Glass ...................................... GW-11, GW-46, GW-50
Grease .............................................................. MA-14
Grille - See Exterior ............................................ EI-20
Ground distribution ........................................... PG-29
H
H/AIM - Wiring diagram ................................... LT-122
H/LAMP - Wiring diagram .................................. LT-42
Harness connector ............................................ PG-71
Harness layout .................................................. PG-42
Hazard warning lamp ....................................... LT-152
Headlamp aiming control ...................... LT-99, LT-122
Headlamp leveler - See Headlamp aiming control ........
LT-122
Headlining - See Roof trim .................................. EI-54
Heated oxygen sensor 1 ..... EC-143, EC-150, EC-301
Heated oxygen sensor 1 (bank 1) .... EC-486, EC-496,
EC-696

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Heated oxygen sensor 1 (bank 2) .... EC-486, EC-496,
EC-696
Heated oxygen sensor 1 heater ...................... EC-308
Heated oxygen sensor 1 heater (bank 1) ........ EC-706
Heated oxygen sensor 1 heater (bank 2) ........ EC-706
Heated oxygen sensor 2 .................................. EC-313
Heated oxygen sensor 2 (bank 1) ..... EC-714, EC-723
Heated oxygen sensor 2 (bank 2) ..... EC-714, EC-723
Heated oxygen sensor 2 heater ...................... EC-319
Heated seat ....................................................... SE-61
Heater and cooling unit (Heater core) ........... ATC-119
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-131
HFC134a (R134a) system service tools .......... ATC-16
HFC134a system service equipment precaution ..........
ATC-12
HLC - Wiring diagram ...................................... WW-43
HO2S1 - Wiring diaram ..................... EC-145, EC-152
Horn ................................................................. WW-62
HORN - Wiring diagram ................................... WW-62
How to erase DTC for OBD system ..... EC-35, EC-376
HSEAT - Wiring diagram ................................... SE-70
I
IATSEN - Wiring diagram .................. EC-325
, EC-731
Idle air volume learning ....................... EC-47, EC-389
Idle speed .............................. EC-40, EC-381, EC-387
Ignition coil ......................................... EC-329, EC-735
Ignition coil(QR20DE) ........................................ EM-31
Ignition coil(VQ23DE and VQ35DE) ................ EM-152
Ignition control system ....................... EC-329, EC-735
Ignition timing ........................ EC-40, EC-381, EC-387
IGNSYS - Wiring diagram .................. EC-330, EC-736
In vehicle sensor ............................. ATC-99, ATC-110
INF/D - Wring diagram ........................... AV-43, AV-65
INJECT - Wiring diagram ................... EC-290, EC-685
Injector ............................................... EC-289, EC-684
Input/Output signal of TCM .............................. CVT-19
Instrument panel .................................................. IP-10
INT/L - Wiring diagram ..................................... LT-217
Intake air temperature sensor ............ EC-324, EC-730
Intake door control linkage adjustment ............ ATC-71
Intake door motor ........................... ATC-69, ATC-117
Intake manifold collector(VQ23DE and VQ35DE) ........
EM-133
Intake manifold(QR20DE) ................................. EM-19
Intake manifold(VQ23DE and VQ35DE) ......... EM-138
Intake sensor ................................ ATC-105, ATC-112
Intake valve timing control ............................... EC-116
Intake valve timing control (Bank 1) ................ EC-461
Intake valve timing control (Bank 2) ................ EC-461
Intake valve timing control solenoid valve (Bank 1) ......
EC-545
Intake valve timing control solenoid valve (Bank 2) ......
EC-545
Interior ................................................................. EI-38
Interior lamp ........................................ LT-217, LT-219
IPDM (Intelligent power distribution module engine room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-119
IVCB1 - Wiring diagram ................................... EC-546
IVCB2 - Wiring diagram ................................... EC-548
K
Knock sensor (KS) ............................. EC-164
, EC-512
KS - Wiring diagram ........................... EC-165, EC-513
L
L/USSV - Wiring diagram ............................... CVT-148
LAN system circuit ........................................... ATC-59
LCD display ....................................................... AV-61
Line pressure and secondary pressure control CVT-20
Line pressure solenoid valve .......... CVT-97, CVT-102
Line pressure test (A/T) ..................................... AT-46
Liquid gasket application(QR20DE) ........... EM-6, LU-3
Liquid gasket application(VQ23DE and VQ35DE) ........
EM-120
, LU-15, CO-3, CO-27
Location of electrical units ................................. PG-67
Lock-up and select control ............................... CVT-21
Lock-up select solenoid valve ........................ CVT-147
LPSV - Wiring diagram ...................... AT-127, CVT-98
Lubricant (R134a) A/C ..................................... ATC-21
Lubricants ......................................................... MA-14
Lubrication circuit (engine)(QR20DE) .................. LU-5
Lubrication circuit (engine)(VQ23DE and VQ35DE) .....
LU-17
Lubrication oil A/C .......................................... ATC-150
M
MAFS - Wiring diagram ..................... EC-126
, EC-468
Magnet clutch ................................. ATC-78, ATC-136
MAIN - Wiring diagram ........ EC-106, EC-451, AT-158
Maintenance (engine)(VQ23DE and VQ35DE) MA-24
Malfunction indicator (MI) .................... EC-36, EC-377
Mass air flow sensor (MAFS) ............. EC-124, EC-466
Meter ..................................................................... DI-4
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ......... EC-344, EC-763
MIL/DL - Wiring diagram .................... EC-344, EC-763
Mirror, door ......................................... GW-74, GW-77
Mirror, out side .................................... GW-74, GW-77
MMSW - Wiring diagram ................................ CVT-114
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-123
Molding - See Exterior EI-25, EI-27, EI-28, EI-29, EI-30
Mud guard - See Exterior .................................... EI-24
Multiport fuel injection (MFI) system .... EC-21, EC-358
Multiport fuel injection precautions ....................... GI-6
N
NATS - Wiring diagram .................................... BL-143
NATS (Nissan anti-theft system) precautions ....... GI-3
NONDTC - Wiring diagram .............. AT-168, CVT-160

IDX-6
ALPHABETICAL INDEX
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (EM)(QR20DE) ............... EM-12
NVH troubleshooting (EM)(VQ23DE and VQ35DE) .....
EM-126
O
O2S1B1 - Wiring diagram .................. EC-488
, EC-498
O2S1B2 - Wiring diagram .................. EC-490, EC-500
Oil cooler (engine)(VQ23DE and VQ35DE) ....... LU-23
Oil filter(QR20DE) .............................................. LU-10
Oil filter(VQ23DE and VQ35DE) ........................ LU-22
Oil pan (engine)(QR20DE) ............................... EM-26
Oil pan (engine)(VQ23DE and VQ35DE) ....... EM-145
Oil pressure (engine)(QR20DE) .......................... LU-7
Oil pressure (engine)(VQ23DE and VQ35DE) .. LU-20
Oil pump (engine)(QR20DE) ............................. LU-11
Oil pump (engine)(VQ23DE and VQ35DE) ....... LU-25
Oil pump regulator valve (engine)(QR20DE) ..... LU-11
Oil pump regulator valve (engine)(VQ23DE and
VQ35DE) ........................................................... LU-25
Oil seal replacement (engine)(QR20DE) ......... EM-53,
EM-62
, EM-70, EM-81
Oil seal replacement (engine)(VQ23DE and VQ35DE)
EM-207
On board diagnostic system ................ EC-33, EC-373
Out side mirror .................................... GW-74, GW-77
Overheat ............................................ EC-218, EC-575
Oversize piston(QR20DE) .............................. EM-103
Oversize piston(VQ23DE and VQ35DE) ........ EM-249
OVRCSV - Wiring diagram .............................. AT-101
P
Park/Neutral position switch .............. EC-238
, EC-614
Park/neutral position switch (A/T) ...... AT-161, AT-210
Park/neutral position switch (CVT) .................. CVT-62
PCV (positive crankcase ventilation) ... EC-30, EC-370
PHASE - Wiring diagram ................................. EC-178
PHSB1 - Wiring diagram .................................. EC-526
PHSB2 - Wiring diagram .................................. EC-528
Pilot bushing replacement - See Pilot
converter(QR20DE) .......................................... EM-81
Pilot bushing replacement - See Pilot
converter(VQ23DE and VQ35DE) .................. EM-228
Piston assembly(QR20DE) ............................... EM-92
Piston assembly(VQ23DE and VQ35DE) ....... EM-240
Piston pin inspection(QR20DE) ........................ EM-99
Piston pin inspection(VQ23DE and VQ35DE) EM-245
Piston ring inspection(QR20DE) ..................... EM-100
Piston ring inspection(VQ23DE and VQ35DE) EM-246
Piston to bore clearance(QR20DE) ................ EM-103
Piston to bore clearance(VQ23DE and VQ35DE) ........
EM-249
PNP/SW - Wiring diagram .. EC-239, EC-615, CVT-64
POS - Wiring diagram ........................ EC-171, EC-519
POWER - Wiring diagram ................... CVT-135, PG-4
Power door mirror .............................................. BL-21
Power seat ......................................................... SE-59
Power steering fluid level .................................. MA-42
Power steering gear ........................................... PS-17
Power steering oil pump .................................... PS-29
Power steering pressure (PSP) sensor .......... EC-185,
EC-533
Power supply routing .......................................... PG-3
Power window .................................................. GW-17
Precations for Leak detection dye .................. ATC-14
Precautions (General) ........................................... GI-4
Pressure control solenoid valve A .. CVT-97, CVT-102
Pressure control solenoid valve B CVT-105, CVT-108
Pressure test (CVT) ........................................ CVT-33
PRGVLV - Wirng diagram ................. EC-283, EC-678
Primary pressure sensor ............................... CVT-126
Primary Speed Sensor .................................... CVT-74
PRIPS - Wiring diagram ................................ CVT-127
PRSCVT - Wiring diagram .............................. CVT-75
PS/SEN - Wiring diagram ................. EC-186, EC-534
PT/SEN - Wiring diagram ................................ AT-121
R
R/FOG - Wiring diagram .................................. LT-144
Radiator(QR20DE) ............................... CO-13, CO-16
Radiator(VQ23DE and VQ35DE) ..................... CO-37
Radio - See Audio .................................... AV-4, AV-18
Rear bumper ....................................................... EI-17
Rear disc brake .................................................. BR-33
Rear door ............................................ BL-119, GW-50
Rear parcel shelf finisher .................................... EI-43
Rear seat ......................................................... SE-112
Rear window defogger ..................................... GW-54
Refrigerant connection precaution .................... ATC-6
Refrigerant discharging evacuating charging ATC-131
Refrigerant general precaution ......................... ATC-6
Refrigerant lines ............................................ ATC-131
Refrigerant pressure sensor EC-339, EC-748, ATC-83,
ATC-144
Refrigeration cycle .......................................... ATC-19
Removal and installation (A/T) ......................... AT-241
Road test ......... AT-48, AT-50, AT-51, AT-52, CVT-35
Rocker cover(QR20DE) .................................... EM-39
Rocker cover(VQ23DE and VQ35DE) ............ EM-160
Room lamp - See Interior lamp ........................ LT-219
ROOM/L - Wiring diagram ............................... LT-225
RP/SEN - Wiring diagram ................. EC-340, EC-749
RRO2 - Wiring diagram .................... EC-314, EC-320
RRO2B1 - Wiring diagram ................ EC-715, EC-724
RRO2B2 - Wiring diagram ................ EC-717, EC-726
S
SEAT - Wiring diagram ...................................... SE-59
Seat belt pre-tensioner disposal ..................... SRS-48
Seat belt, front ..................................................... SB-3
Seat, rear ......................................................... SE-112
Secondary pressure sensor .......................... CVT-118
Secondary Speed Sensor ............................... CVT-79
SECPS - Wiring diagram .............................. CVT-119