keyless NISSAN TEANA 2003 Service Manual

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS

BCM STATUS CONTROL
BCM changes its status depending on the operation status in order to save power consumption.
1. CAN communication status

With ignition switch ON, CAN communicates with other control units normally.

Control by BCM is being operated properly.

When ignition switch is OFF, switching to sleep mode is possible.

Even when ignition switch is OFF, if CAN communication with IPDM E/R, Intelligent Key unit or unified
meter and A/C amp. is active, CAN communication status is active.
2. Sleep transient status

This status shuts down CAN communication when ignition switch is turned OFF.

It transmits sleep request signal to IPDM E/R, Intelligent Key unit, driver seat control unit and unified
meter and A/C amp.

2 seconds after CAN communication of all control units stops, sleep transient status switches to CAN
communication inactive status.
3. CAN communication inactive status

With ignition switch OFF, CAN communication is not active.

With ignition switch OFF, control performed only by BCM is active.

When all controls that BCM performs stop, CAN communication inactive status switches to sleep sta-
tus.
4. Sleep status

BCM is activated with low power mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state.
–Ignition switch (ACC, ON)
–Key switch
–Ignition knob switch
–Hazard switch
–Door lock/unlock switch
–Front door switch (driver side, passenger side)
–Rear door switch (RH, LH)
–Trunk lid opener switch
–Trunk room lamp switch
–Combination switch (passing, lighting switch 1ST position, front fog lamp)
–Remote keyless entry receiver (lock/unlock signal)

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.

BCS-8
BCM (BODY CONTROL MODULE)

SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM, COMBINATION METER AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
System Reference
Power door lock systemBL-21, "
POWER DOOR LOCK SYSTEM"
Remote keyless entry systemBL-46, "REMOTE KEYLESS ENTRY SYSTEM"
Power window system NOTEGW-17, "POWER WINDOW SYSTEM"
Sunroof NOTERF-10, "SUNROOF"
Interior room lamp timerLT-219, "INTERIOR ROOM LAMP"
Interior room lamp battery saver controlLT-222, "INTERIOR ROOM LAMP BATTERY SAVER CONTROL"
Rear fog lampLT-142, "REAR FOG LAMP"
System Reference
NATSBL-139, "
NATS(Nissan Anti-Theft System)"
Headlamp
LT- 6 , "HEADLAMP - XENON TYPE -"

LT-38, "HEADLAMP - HALOGEN TYPE -"
Auto light systemLT-64, "AUTO LIGHT SYSTEM"
Parking, license plate and tail lamps LT-196, "PARKING, LICENSE PLATE AND TAIL LAMPS"
Front fog lampLT-126, "FRONT FOG LAMP"
Exterior lamp battery saver controlLT-197, "EXTERIOR LAMP BATTERY SAVER CONTROL"
Front wiper and washer systemWW-4, "FRONT WIPER AND WASHER SYSTEM"
Headlamp washerWW-40, "HEADLAMP WASHER"
Rear window defoggerGW-54, "REAR WINDOW DEFOGGER"
System Reference
Warning chimeDI-56, "
WARNING CHIME"
Turn signal and hazard warning lampsLT-152, "TURN SIGNAL AND HAZARD WARNING LAMPS"
System Reference
Oil pressure warning lampDI-35, "
WARNING LAMPS"
System Reference
Intelligent Key systemBL-68, "
INTELLIGENT KEY SYSTEM"

BCM (BODY CONTROL MODULE)
BCS-9
C
D
E
F
G
H
I
J
L
MA
B
BCS

MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote control entry system

Remote keyless entry receiver

Key switch

Front door switch (driver side)

Front door switch (passenger side)

Rear door switch RH

Rear door switch LH

Front door lock assembly
(driver side) (door lock actuator)

Front door lock assembly
(passenger side) (door lock actuator)

Rear door lock actuator RH

Rear door lock actuator LH

Trunk lid opener actuator

Turn signal lamp (RH, LH)

Combination meter
(turn signal indicator, warning chime)
Intelligent Key system

Intelligent Key unit

Front door switch (driver side)

Front door switch (passenger side)

Rear door switch RH

Rear door switch LH

Front door lock assembly
(driver side) (door lock actuator)

Front door lock assembly
(passenger side) (door lock actuator)

Rear door lock actuator RH

Rear door lock actuator LH

Trunk lid opener actuator

Turn signal lamp (RH, LH)

Combination meter
(turn signal indicator, warning chime)
Power door lock system

Power window main switch
(door lock and unlock switch)

Front door lock assembly (driver side)
(door unlock sensor)

Key switch

Front door switch (driver side)

Front door switch (passenger side)

Rear door switch RH

Rear door switch LH

Front door lock assembly
(driver side) (door lock actuator)

Front door lock assembly
(passenger side) (door lock actuator)

Rear door lock actuator RH

Rear door lock actuator LH
Trunk lid openerTrunk lid and fuel lid opener switch
(Trunk lid opener switch)Trunk lid lock assembly
(trunk lid opener actuator)
Power supply (IGN) to power window,
sunroofIgnition power supply Power window and sunroof system
Power supply (BAT) to power window,
sunroof and power seatBattery power supply Power window, sunroof system and power seat
Headlamp Combination switch

IPDM E/R

Combination meter
(HIGH beam indicator)
Exterior lamp battery saver control

Ignition switch

Combination switchIPDM E/R
Auto light system

Optical sensor

Combination switch

Ignition switch (ACC, ON)IPDM E/R
Parking, license plate and tail lamps Combination switch

IPDM E/R

Combination meter (Tail lamp indicator)
Front fog lamp Combination switch

IPDM E/R

Combination meter
(Front fog lamp indicator)

BCS-10
BCM (BODY CONTROL MODULE)

CAN Communication UnitBKS001UH
Refer to LAN-49, "CAN System Specification Chart" .
Rear fog lamp Combination switch

Rear fog lamp

Combination meter
(Rear fog lamp indicator)
Turn signal lamp

Combination switch

Ignition switch (ON)

Turn signal lamp

Combination meter
(turn signal indicator, warning chime)
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
(turn signal indicator, warning chime)
Interior room lamp timer

Key switch

Remote keyless entry receiver

Power window main switch
(door lock and unlock switch)

Front door lock assembly (driver side)

Front door switch (driver side)

Front door switch (passenger side)

Rear door switch LH

Rear door switch RH

Ignition switch (ON)

Map lamp

Personal lamp RH

Personal lamp LH

Ignition keyhole illumination
Key warning chime

Key switch

Front door switch (driver side)

Ignition switch (ON)Combination meter (warning buzzer)
Light warning chime

Combination switch

Front door switch (driver side)

Ignition switch (ON)Combination meter (warning buzzer)
Oil pressure warning lamp

IPDM E/R

Ignition switch (ON)Combination meter (warning lamp)
Front wiper and washer system

Combination switch

Combination meter

Ignition switch (ON)IPDM E/R
Headlamp washer

Headlamp washer switch

Combination switch

Ignition switch (ON)IPDM E/R
Rear window defogger

Rear window defogger switch

Ignition switch (ACC, ON)IPDM E/R
A/C switch signal

Unified meter and A/C amp.

Ignition switch (ON)ECM
Blower fan switch signal

Unified meter and A/C amp.

Ignition switch (ON)ECM System Input Output

BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS

CONSULT-II Function (BCM)BKS001UK
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
×:Applicable
NOTE:
This item is displayed, but should not be used.BCM diagnostic test item Check item, diagnostic test mode Content
Inspection by partWORK SUPPORT Changes setting of each function.
SELF-DIAGNOSIS RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
CAN DIAG SUPPORT MNTRThe result of transmit/receive diagnosis of CAN communication
can be read.
ACTIVE TEST Gives a drive signal to a load to check the operation.
ECU PART NUMBER ECM part number can be read.
CONFIGURATION (Not be used.)
CONSULT-II display System and itemDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSDATA
MONITORCAN
DIAG
SUP-
PORT
MNTRACTIVE
TESTECU
PA R T
NUMBERCON-
FIGU-
RATION
BCM BCM×× × ×
×
NOTE
DOOR LOCK Power door lock system×××
REAR DEFOGGER Rear window defogger××
BUZZER Warning chime××
INT LAMP Room lamp timer×××
MULTI REMOTE ENTRemote keyless entry
system×××
HEAD LAMP Headlamp×××
WIPER Wiper×××
FLASHERTurn signal lamp
Hazard lamp××
AIR CONDITONERBlower fan switch signal
A/C switch signal×
INTELLIGENT KEY Intelligent Key system×
COMB SW Combination switch×
IMMU NATS××
BATTERY SAVER Room lamp battery saver×× ×
TRUNK Trunk lid opener××
SIGNAL BUFFER Oil pressure switch××
PANIC ALARM Panic alarm×

BL-2 Check Door Lock Actuator Output Signal ............... 39
Check Door Lock Actuator Circuit .......................... 40
(DRIVER SIDE AND REAR LH) .......................... 40
(PASSENGER SIDE AND REAR RH) ................. 41
Check Door Unlock Sensor .................................... 42
FUEL FILLER LID OPENER ..................................... 44
Component Part and Harness Connector Location ... 44
Wiring Diagram –F/LID– ......................................... 45
REMOTE KEYLESS ENTRY SYSTEM ..................... 46
Component Parts and Harness Connector Location ... 46
System Description ................................................. 46
INPUTS ............................................................... 46
OPERATED PROCEDURE ................................. 47
CAN Communication System Description .............. 48
CAN Communication Unit ....................................... 48
Schematic ............................................................... 49
Wiring Diagram — KEYLES— ................................ 50
FIG. 1 ................................................................... 50
FIG. 2 ................................................................... 51
FIG. 3 ................................................................... 52
Terminals and Reference Value for BCM ................ 53
Terminals and Reference Value for IPDM E/R ........ 54
CONSULT-II Function (BCM) .................................. 54
CONSULT-II START PROCEDURE .................... 54
CONSULT-II APPLICATION ITEMS .................... 54
Work Flow ............................................................... 56
Trouble Diagnosis Symptom Chart ......................... 56
Check Key Fob Battery and Function ..................... 57
Check ACC Switch ................................................. 58
Check Door Switch ................................................. 59
CHECK DOOR SWITCH (EXCEPT TRUNK
ROOM LAMP SWITCH) ...................................... 59
CHECK TRUNK ROOM LAMP SWITCH ............ 61
Check Key Switch ................................................... 63
Check Hazard Function .......................................... 64
Check Map Lamp and Ignition Keyhole Illumination
Function .................................................................. 64
ID Code Entry Procedure ....................................... 64
KEY FOB ID SET UP WITH CONSULT-II ........... 64
KEY FOB ID SET UP WITHOUT CONSULT-II .... 66
Key Fob Battery Replacement ................................ 67
INTELLIGENT KEY SYSTEM ................................... 68
Component Parts and Harness Connector Location ... 68
System Description ................................................. 70
DOOR LOCK/UNLOCK, TRUNK OPEN FUNC-
TION .................................................................... 70
REMOTE KEYLESS ENTRY FUNCTIONS ......... 71
ENGINE START FUNCTION ............................... 72
WARNING AND ALARM FUNCTION .................. 73
CHANGE SETTINGS FUNCTION ....................... 76
INTELLIGENT KEY REGISTRATION .................. 76
STEERING LOCK UNIT REGISTRATION .......... 77
CAN Communication System Description .............. 77
CAN Communication Unit ....................................... 77
Schematic ............................................................... 78
Wiring Diagram — I/KEY— .................................... 80
Terminals and Reference Value for Intelligent Key
Unit ......................................................................... 88
Terminals and Reference Value for Steering Lock Unit .......................................................................... 90
Terminals and Reference Value for BCM ................ 90
Diagnosis Procedure ............................................... 91
WORK FLOW ...................................................... 91
ENGINE START FUNCTION DIAGNOSTIC
PROCEDURE ...................................................... 92
CONSULT-II Functions (INTELLIGENT KEY) ......... 93
CONSULT-II Inspection Procedure ......................... 93
BASIC OPERATION ............................................ 93
CONSULT-II Application Items ................................ 93
SELF-DIAGNOSTIC RESULTS ........................... 93
DATA MONITOR .................................................. 93
WORK SUPPORT ............................................... 94
ACTIVE TEST ...................................................... 95
Trouble Diagnosis Symptom Chart ......................... 96
ALL FUNCTIONS OF THE INTELLIGENT KEY
ARE NOT OPERATING ....................................... 96
REMOTE KEYLESS ENTRY FUNCTION MAL-
FUNCTION .......................................................... 96
DOOR LOCK FUNCTION MALFUNCTION ......... 97
TRUNK OPEN FUNCTION MALFUNCTION ....... 97
HAZARD REMINDER FUNCTION MALFUNC-
TION .................................................................... 98
ENGINE START FUNCTION MALFUNCTION .... 98
WARNING CHIME FUNCTION MALFUNCTION ... 99
Check CAN Communication System ....................100
Check Intelligent Key Unit Power Supply and
Ground Circuit .......................................................100
Check Key Switch (Intelligent Key Unit Input) .......101
Check Key Switch (BCM Input) .............................102
Check Ignition knob Switch ...................................103
Check Door Switch ...............................................105
CHECK DOOR SWITCH (EXCEPT TRUNK
ROOM LAMP SWITCH) .....................................105
CHECK TRUNK ROOM LAMP SWITCH ...........107
Check Door Request Switch .................................109
Check Intelligent Key Warning Buzzer .................. 111
Check Outside Key Antenna .................................112
Check Inside Key Antenna ....................................114
Check Steering Lock Unit ......................................115
Check Headlamp Function ....................................117
Removal and Installation of Intelligent Key Unit ....117
REMOVAL ..........................................................117
INSTALLATION ..................................................117
Intelligent Key Battery Replacement .....................117
DISASSEMBLY AND ASSEMBLY OF INTELLI-
GENT KEY .........................................................117
INTELLIGENT KEY BATTERY INSPECTION ...118
DOOR ......................................................................119
Fitting Adjustment .................................................119
FRONT DOOR ...................................................119
REAR DOOR .....................................................119
STRIKER ADJUSTMENT ..................................120
Removal and Installation of Front Door ................120
REMOVAL ..........................................................120
INSTALLATION ..................................................120
Removal and Installation of Rear Door .................120
REMOVAL ..........................................................121

BL-30
POWER DOOR LOCK SYSTEM

CONSULT-II Function (BCM)BIS000W3
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-34, "CONSULT-II Start Procedure" .
CONSULT-II APPLICATION ITEMS
Data Monitor
*: With Intelligent Key system
Active Test
BCM diagnosis
partInspection item, Self-diagnosis
modeContent
Door lockDATA MONITOR Displays BCM input data on real-time basis.
ACTIVE TEST Sends drive signals to door lock actuator to perform operation check.
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock and unlock switch.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch driver side.
DOOR SW-AS Indicates [ON/OFF] condition of front door switch passenger side.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW This is displayed even when it is not equipped.
LOCK STATUS Indicates [ON/OFF] condition of driver side door lock knob
SHOCK SENSOR Indicates [ON/OFF] condition of shock sensor
VEHICLE SPEED Indicates [km/h] condition of vehicle speed
KEYLESS LOCK Indicates [ON/OFF] condition of lock signal from keyfob.
KEYLESS UNLOCK Indicates [ON/OFF] condition of unlock signal from keyfob.
I-KEY LOCK* Indicates [ON/OFF] condition of lock signal from door request switch.
I-KEY UNLOCK* Indicates [ON/OFF] condition of unlock signal from door request switch.
Test item Content
DOOR LOCKThis test is able to check all door lock actuators lock or unlock operation.
These actuators lock or unlock when “LOCK” or “UNLOCK” on CONSULT-II screen is touched.

BL-46
REMOTE KEYLESS ENTRY SYSTEM

REMOTE KEYLESS ENTRY SYSTEMPFP:28596
Component Parts and Harness Connector LocationBIS000WE
System DescriptionBIS000WF
INPUTS
Power is supplied at all times

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55.

through 15A fuse [No. 17, located in the fuse block (J/B)]

to BCM terminal 42.
When the key switch is ON (key is inserted in ignition key cylinder), power is supplied

through 15A fuse [No. 17, located in the fuse block (J/B)]

through key switch terminals 1 and 4

to BCM terminal 37.
When the ignition switch is ACC or ON, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
When the ignition switch is ON or START, power is supplied

through 10A fuse [No. 1, located in the fuse block (J/B)]
1. BCM M3,M4,M5 2. Front door switch B10
(Driver side)3. Rear door switch (LH) B14
4. Key switch and key lock solenoid
connector M345. Trunk lid lock assembly T7
(Trunk room lamp switch)
PIIB8749E

REMOTE KEYLESS ENTRY SYSTEM
BL-47
C
D
E
F
G
H
J
K
L
MA
B
BL


to BCM terminal 38.
Ground supplied

to BCM terminal 52

through body ground M71 and M72.
When the front door switch (driver side) is ON (door is OPEN), ground is supplied

to BCM terminal 62

through front door switch (driver side) terminal 2

through front door switch (driver side) case ground.
When the front door switch (passenger side) is ON (door is OPEN), ground is supplied

to BCM terminal 12

through front door switch (passenger side) terminal 2

through front door switch (passenger side) case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 63

through rear door switch LH terminal 2

through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied

to BCM meter terminal 13

through rear door switch RH terminal 2

through rear door switch RH case ground.
When the trunk room lamp switch is ON (Door is OPEN), ground is supplied

to BCM terminal 57

through trunk lid lock assembly terminals 3 and 1

through body ground B214 and B217.
Key fob signal is inputted to BCM (the antenna of the system is combined with BCM).
The remote keyless entry system controls operation of the

power door lock

hazard reminder

auto door lock

panic alarm

room lamp and key ring illumination
OPERATED PROCEDURE
Power Door Lock Operation
BCM receives a LOCK signal from key fob. BCM locks all doors with input of LOCK signal from key fob.
BCM receives a UNLOCK signal from key fob. BCM unlocks all doors with input of UNLOCK signal from key
fob.
Hazard Reminder
When the doors are locked or unlocked by key fob, supply power to hazard warning lamp flashes as follows

LOCK operation: 3 or 4 mode (flash once)

UNLOCK operation: 2 or 4 mode (flash twice)
The hazard reminder has 1, 2, 3 or 4 mode
Operating function of hazard reminder
Hazard reminder does not operate if any door switch is ON (any door is OPEN).
How to change hazard reminder mode
mode 1 mode 2 mode 3 mode 4
Remote controller
operationLock Unlock Lock Unlock Lock Unlock Lock Unlock
Hazard warning lamp
flash— — — Twice Once — Once Twice

BL-48
REMOTE KEYLESS ENTRY SYSTEM

With CONSULT-II
Hazard reminder can be changed using “HAZARD LAMP SET” mode in “WORK SUPPORT”.
Refer to BL-54, "
Work Support" .
Auto Door Lock Operation
Auto lock function signal is sent for operation when any of the following signals are not sent within 30 seconds
after the unlock signal is sent from the key fob:

when door switch is turned ON for open.

when the key switch is turned ON.

when the lock signal is sent from the key fob.
Auto door lock mode can be changed using “AUTO LOCK SET” mode in “WORK SUPPORT”.
Refer to BL-54, "
Work Support" .
Room Lamp and Ignition Key ring Illumination Operation
When the following conditions come:

condition of interior lamp switch is DOOR position;

door switch OFF (when all the doors are closed);
Remote keyless entry system turns on interior lamp (for 30 seconds) with input of UNLOCK signal from key
fob. For detailed description, refer to LT- 2 1 9 , "
INTERIOR ROOM LAMP" .
CAN Communication System DescriptionBIS000WG
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBIS000WH
Refer to LAN-49, "CAN System Specification Chart" .