NISSAN TEANA 2014 Service Manual

HOOD
DLK-173
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
2. Remove cowl top side trim covers (LH/RH). Refer to EXT-24, "Removal and Installation".
3. Loosen hood hinge (LH/RH) nuts and bolts. NOTE:
The anticorrosive agent applied between the hoodledge and the hood hinges also acts as an adhesive.
This seal must be broken before the hinges will move.
4. Release the radiator core support upper cover clips (A), then remove radiator core support upper cover.
5. Loosen the hood lock assembly bolts.
6. Adjust the hood assembly so the clearance m easurements are within specifications provided.
7. Tighten the hood hinge nuts and bolts to specified torque.
8. Tighten the hood lock assembly bolts to specified torque.
9. Install the radiator core support upper cover.
10. Install the hoodledge finishers.
11. Install cowl top side trim covers. Refer to EXT-24, "Removal and Installation"
.
HEIGHT ADJUSTMENT
1. Release the radiator core support upper cover clips (A), then
remove radiator core support upper cover.
2. Loosen the hood lock assembly bolts.
3. Adjust the surface height of hood assembly to front bumper fas- cia and front fender according to the specified values by rotating
hood bumper rubbers (LH/RH).
ALKIA2602ZZ
Hood hinge nuts 13.5 N·m (1.4 kg-m, 10 ft-lb)
Hood hinge to body bolts 13.5 N·m (1.4 kg-m, 10 ft-lb)
Hood lock assembly bolts 22 N·m (2.2 kg-m, 16 ft-lb)
ALKIA2602ZZ
ALKIA0023GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-174
< REMOVAL AND INSTALLATION >
HOOD
4. Temporarily tighten hood lock assembly bolts.
5. Adjust (A) and (B) as shown to the following val ue with hood's own weight by dropping it from approxi-
mately 200 mm (7.87 in) height or by pressing hood light ly [approximately 29 N-f (3.0 kg-f, 6.5 lb-f)].
6. After adjustment, tighten hood hinge nuts and bolts to the specified torque. CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After adjusting, apply touch-up paint (body color) onto the head of hood hinge bolts and nuts.
7. Tighten the hood lock assembly bolts to specified torque.
8. Install the radiator core support upper cover.
9. If the clearance measurements between the hood and fender cannot be corrected by adjusting the hood,
the fender must be adjusted. Refer to DLK-182, "Adjustment"
.
HOOD HINGE
HOOD HINGE : Removal and InstallationINFOID:0000000009461925
REMOVAL
1. Remove hood assembly. Refer to DLK-170, "HOOD ASSEMBLY : Removal and Installation".
2. Remove hood hinge bolts (A), and then remove hood hinge (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten hood hinge bolts to specified torque.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
1. Hood striker 2. Primary latch 3. Secondary striker
4. Secondary latch A. 21 ± 1 mm (0.8 ± 0.04 in) B. 6.8 mm (0.27 in)
PIIB5794E
Hood lock assembly bolts 22 N·m (2.2 kg-m, 16 ft-lb)
ALKIA2682ZZ
Hood hinge bolts 13.5 N·m (1.4 kg-m, 10 ft-lb)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

HOOD
DLK-175
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
• After installation, perform hood assem bly adjustment procedure. Refer to DLK-172, "HOOD ASSEM-
BLY : Adjustment".
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and InstallationINFOID:0000000009461926
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
HOOD LOCK CONTROL
HOOD LOCK CONTROL : Co mponent Parts LocationINFOID:0000000009461927
1. Hood lock assembly 2. Hood lock release cable 3. Hood lock/fuel filler door
release handle assembly
A. Hood lock release cable clip Clip
ALKIA2663ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-176
< REMOVAL AND INSTALLATION >
HOOD
HOOD LOCK CONTROL : Re moval and Installation
INFOID:0000000009461928
REMOVAL
1. Release the radiator core support upper cover clips, then remove the radiator core support upper cover.
2. Remove the hoodledge finisher clips (LH), then remove the hoodledge finisher LH.
3. Disconnect the hood switch harness connector (A) (if equipped). : Front
4. Remove the hood lock assembly bolts ( ).
5. Disconnect the hood lock release cable from t he hood lock assembly and unclip from the hoodledge.
6. Remove the fender protector LH. Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
7. Remove the bolts (A), then separate the hood lock/fuel filler door release handle assembly (1) from the hood lock release cable
(3) and fuel filler door release cable (2).
8. Remove the grommet from the upper dash assembly and pull the hood lock release cable into the passen- ger compartment.
CAUTION:
While pulling, be careful no t to damage (peel) the outsid e of the hood lock release cable.
INSTALLATION
1. Pull the hood lock release cable through the upper dash assembly into the engine compartment.
CAUTION:
Be careful not to bend the cable too much , keep the radius 100 mm (3.94 in) or more.
ALKIA2664ZZ
ALKIA0027GB
ALKIA2665ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

HOOD
DLK-177
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
2. Attach the hood lock release cable (3) and the fuel filler door release cable (2) to the hood lock/fuel filler door release handle
assembly (1).
3. Place hood lock/fuel filler door release handle assembly in posi- tion and retain with bolts (A).
4. Check that the cable is not offset from the center of the grommet
and seat the grommet into the upper dash hole.
NOTE:
Make sure that the marked area (A) of the cable is located as
shown after mounting grommet to dash upper assembly.
Apply sealant around the grommet at * mark.
5. Position the hood lock release cable and clip it into place.
6. Install the hoodledge finisher (LH) and retain with clips.
7. Connect the hood lock release cable to the hood lock assembly.
8. Install the fender protector (LH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
9. Perform hood fitting adjustment. Refer to DLK-172, "HOOD ASSEMBLY : Adjustment"
.
10. Perform the hood lock control inspection.
INSPECTION
NOTE:
If the hood lock release cable is bent or deformed, replace it.
1. Check that the secondary latch is properly engaged wi th the secondary striker and meets specification
provided (B) with hood's own weight.
ALKIA2665ZZ
ALKIA2139ZZ
PIIB5802E
PIIB5794E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-178
< REMOVAL AND INSTALLATION >
HOOD
2. While operating the hood lock release handle, carefully check that the front end of the hood assembly is
raised and meets the specification provided (A). Al so check that the hood lock release handle returns to
the original position.
3. Check that the hood lock release handle operating force is 49 N (5.0 kg-f, 11 lb-f) or less.
4. Install so the static closing force of the hood assembly is 254 – 490 N (25.9 – 50 kg-f, 57.1 - 110.2 lb-f).
5. Check the hood lock assembly lubrication condition. If neces- sary, apply a suitable multi-purpose grease as shown.
1. Hood striker 2. Primary latch 3. Secondary striker
4. Secondary latch A. 21 ± 1 mm (0.8 ± 0.04 in) B. 6.8 mm (0.27 in)
ALKIA0028GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

RADIATOR CORE SUPPORTDLK-179
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
RADIATOR CORE SUPPORT
Removal and InstallationINFOID:0000000009461929
CAUTION:
Before servicing, turn igni tion switch OFF, disconnect both batt ery terminals and wait at least three
minutes.
REMOVAL
1. Remove crash zone sensor. Refer to SR-22, "Removal and Installation".
2. Remove radiator. Refer to CO-17, "Removal and Installation"
(QR25DE) or CO-41, "Removal and Installa-
tion" (VQ35DE).
3. Remove the hood lock. Refer to DLK-176, "HOOD LOCK CONTROL : Removal and Installation"
.
4. Remove air guides (LH/RH).
5. Remove and disconnect all remaining harness connectors and clips from the radiator core support assembly, and position aside.
6. Remove the bolts and the radiator core support assembly.
7. Remove the following parts after removing radiator core support assembly. • Cooling fan. Refer to CO-18, "Exploded View"
(QR25DE) or CO-42, "Exploded View" (VQ35DE).
1. Radiator core support 2. Air guide (QR25DE only) 3. Air guide (VQ35DE only)
4. Hood switch bracket A. Bolt B. Clips
ALKIA2744ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-180
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
• Hood switch bracket (if equipped).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing, perform hood fitting adjustment. Refer to DLK-172, "HOOD ASSEMBLY : Adjustment"
.
Radiator core support
bolts 21 N·m (2.1 kg-m, 15 ft-lb)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT FENDERDLK-181
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
FRONT FENDER
Exploded ViewINFOID:0000000009461930
Removal and InstallationINFOID:0000000009461931
NOTE:
LH side shown; RH side similar.
REMOVAL
1. Remove fender protector LH. Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation".
2. Remove the front combination lamp. Refer to EXL-126, "Removal and Installation - Xenon"
(Xenon) or
EXL-128, "Removal and Installation - Halogen"
(Halogen).
3. Remove the cowl top side trim cover. Refer to EXT-24, "Removal and Installation"
.
4. Remove mudguard. Refer to EXT-30, "Removal and Installation"
.
5. Remove the bolts and the front fender. CAUTION:
Use a shop cloths to protect the body from being damaged during removal and installation.
6. Remove front fender baffle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform fender adjustment procedure. Refer to DLK-182, "Adjustment"
.
1. Hoodledge finisher (LH) 2. Front fender stay (LH) 3. Front fender (LH)
4. Front fender baffle (LH) 5. Cowl top side cover
ALKIA2698ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-182
< REMOVAL AND INSTALLATION >
FRONT FENDER
Adjustment
INFOID:0000000009461932
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dures.
Unit: mm (in)
Adjustment
1. Remove hoodledge finisher.
2. Remove the cowl top side trim cover. Refer to EXT-24, "Removal and Installation"
.
3. Remove front fascia. Refer to EXT-17, "Removal and Installation"
.
4. Remove the front fender protector. Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
5. Remove the mudguard. Refer to EXT-30, "Removal and Installation"
.
6. Loosen the front fender bolts.
7. Adjust the clearance (J) and surface height (K ) between the front fender and the front door.
8. Tighten the rear upper and lower front fender bolts.
1. Hood assembly 2. Front fender 3. Front fascia
4. Body side outer 5. Front door assembly
Section Item Measurement Standard Parallelism Equality A – A E Clearance 3.5
± 1 (0.14 ± 0.04) < 1.5 (0.06) < 2.0 (0.08)
F Surface height 0.0 + 1 (0.0 + 0.04) — < 1.5 (0.06)
B – B G Clearance 0.0 + 0.8,
− 0.0 (0.0 + 0.03, − 0.0) — —
H Surface height 0.7 ± 1.0 (0.03 ± 0.04) ≤ 1.0 (0.04) ≤ 1.0 (0.04)
C – C J Clearance 3.6
± 1.0 (0.14 ± 0.04) — —
K Surface height 0.0 ± 1.0 (0.0 ± 0.04) — —
D – D M Clearance 2.35
± 1.0 (0.09 ± 0.04) ≤ 1.0 (0.04) —
N Surface height − 0.0 ± 1.0 (0.0 ± 0.04) — —
AWKIA2563ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM