NISSAN TERRANO 2002 Service Repair Manual

Trouble Diagnoses
WORK FLOW
CHECK IN
Listen to customer complaints or request. (Get symptoms)
TROUBLEKEY SERVICE REQUEST (Additional key ID registration)H
Verify the security indicator and MI*.INITIALISATION
(Refer to CONSULT-II operation
manual NATS.)
EUsing the CONSULT-II program card for NATS check the
ªSELF-DIAG RESULTSº with CONSULT-II.F
Self-diagnostic results referring to NATS, but no information
about engine self-diagnostic results is displayed on CONSULT-
II.
Turn ignition switch ªOFFº.
Repair NATS.
(If necessary, carry out ªC/U INITIALIZATIONº with CONSULT-
II.)
Turn ignition switch ªONº.
Erase the NATS ªSELF-DIAG RESULTSº by using CONSULT-
II. (Touch ªERASEº.)
Start the engine.
NGVerify no lighting up of the security indicator.
OK
CHECK OUT
Perform running test with CONSULT-II in engine ªSELF-DIAG
RESULTSº mode.
NGVerify ªNO DTC IS DETECTEDº displayed on the CONSULT-II
screen.
OK
CHECK OUT
Self-diagnostic results referring to NATS and ªDON'T
ERASE BEFORE CHECKING ENG DIAGº are displayed on
CONSULT-II.
(This means that engine trouble data has been detected in
ECM.)
Turn ignition switch ªOFFº.
Repair NATS according to self-diagnostic results referring to
NATS.
(If necessary, carry out ªC/U INITIALIZATIONº with CON-
SULT-II.)
Do not erase the NATS ªSELF-DIAG RESULTSº by using
CONSULT-II.
Check the engine ªSELF-DIAG RESULTSº with CONSULT-II
by using the CONSULT-II generic program card.
(Engine diagnostic software included)
OK
F
Repair engine control system (Refer to EC section.) when
self-diagnostic results except ªNATS MALFUNCTIONº are
detected. When only ªNATS MALFUNCTIONº is detected,
erase the self-diagnostic results and go to the next step.
Start the engine. Does the engine start properly?NG
Erase the NATS and engine ªSELF-DIAG RESULTSº by
using the CONSULT-II program card for NATS and generic
program card.
Start the engine.
H
H
H
HH
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
NATS (Nissan Anti-Theft System)
EL-195

SYMPTOM MATRIX CHART 1
(Self-diagnosis related item)
SYMPTOMDisplayed ªSELF-DIAG
RESULTSº on
CONSULT-II screenDIAGNOSTIC
PROCEDURE
(Reference page)SYSTEM
(Malfunctioning part or mode)REFERENCE PART NO.
OF ILLUSTRATION ON
NEXT PAGE
ISecurity indicator light-
ing up*
IEngine does not startECM INT CIRC-IMMUPROCEDURE 1
(EL-198)ECM B
ISecurity indicator light-
ing up*
IEngine does not startCHAIN OF ECM-IMMUPROCEDURE 2
(EL-199)Open circuit in battery voltage line
of IMMU circuitC1
Open circuit in ignition line of IMMU
circuitC2
Open circuit in ground line of IMMU
circuitC3
Open circuit in communication line
between IMMU and ECMC4
Short circuit between IMMU and
ECM communication line and bat-
tery voltage lineC4
Short circuit between IMMU and
ECM communication line and
ground lineC4
ECM B
IMMU A
DIFFERENCE OF KEYPROCEDURE 3
(EL-201)Unregistered key D
IMMU A
CHAIN OF IMMU-KEYPROCEDURE 4
(EL-202)Malfunction of key ID chip E
IMMU A
Open circuit in ground line of
dongle circuitC6
Open or short circuit in communica-
tion line between IMMU and dongle
control unitC5
Dongle control unit G
ID DISCORD, IMM-ECMPROCEDURE 5
(EL-204)System initialisation has not yet
been completed.F
ECM B
LOCK MODEPROCEDURE 7
(EL-206)LOCK MODE D
IMI staying ON
ISecurity indicator light-
ing up*DON'T ERASE BEFORE
CHECKING ENG DIAGWORK FLOW
(EL-195)Engine trouble data and NATS
trouble data have been detected in
ECM.Ð
*: When NATS detects trouble, the security indicator lights up while ignition key is in the ªONº position.
*: When the vehicle is equipped with dongle control unit (RHD models), the security indicator blinks 6 times just after ignition switch is turned
to ON. Then the security indicator lights up while ignition key is in the ªONº position.
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-196

SYMPTOM MATRIX CHART 2
(Non self-diagnosis related item)
SYMPTOMDIAGNOSTIC PROCEDURE
(Reference page)SYSTEM
(Malfunctioning part or mode)REFERENCE PART
NO. OF ILLUSTRATION
ON NEXT PAGE
ISecurity ind. does not light up.PROCEDURE 6
(EL-205)Security ind.
Open circuit between Fuse and
NATS IMMU
Continuation of initialization mode
NATS IMMU
Security ind. does not blink just
after initialization even if the vehicle
is equipped with dongle unit.
PROCEDURE 8
(EL-207)NATS might be initialized without connecting dongle unit properly.
Open circuit in ground line of
dongle control circuitC6
Security ind. does not blink just
after ignition switch is turned to ON
when some malfunction related to
NATS is detected even if the
vehicle is equipped with dongle
unit.Open or short circuit in communica-
tion line between IMMU and dongle
control unitC5
Dongle control unit G
DIAGNOSTIC SYSTEM DIAGRAM
NEL559
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-197

DIAGNOSTIC PROCEDURE 1
Self-diagnostic results:
ªECM INT CIRC-IMMUº displayed on CONSULT-II screen
Confirm SELF-DIAGNOSTIC RESULTS ªECM INT CIRC-IMMUº dis-
played on CONSULT-II screen.
Ref. part No. B.
Replace ECM.
Perform initialisation with CONSULT-II.
For the operation of initialisation, refer to ªCONSULT-II operation manual
NATSº.
SEL314W
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-198

DIAGNOSTIC PROCEDURE 2
Self-diagnostic results:
ªCHAIN OF ECM-IMMUº displayed on CONSULT-II screen
Confirm SELF-DIAGNOSTIC
RESULTS ªCHAIN OF ECM-IMMUº
displayed on CONSULT-II screen.
OK
CHECK POWER SUPPLY CIRCUIT FOR
IMMU.
Check voltage between IMMU terminalq
8
and ground.
Battery voltage should exist.
OK
ENG
Check the following.
I10A fuse (ZD30DDTi
models) or 20A fuse
(TD27Ti models) (No.
16)
IHarness for open or
short between fuse and
IMMU connector
Ref. part No. C1
CHECK IGN SW. ON SIGNAL.
Check voltage between IMMU terminalq
7
and ground while ignition switch is ªONº
position.
Battery voltage should exist.
OK
ENG
Check the following.
I10A fuse (No.
11 ,
located in the fuse
block)
IHarness for open or
short between fuse and
IMMU connector
Ref. part No. C2
CHECK GROUND CIRCUIT FOR IMMU.
Check continuity between IMMU terminal
q
4and ground.
Continuity should exist.
OK
ENG
Repair harness.
Ref. part No. C3
CHECK COMMUNICATION OPEN CIR-
CUIT.
Check continuity between IMMU terminal
q
1and ECM terminal410(TD27Ti mod-
els) orq
55(ZD30DDTi models).
Continuity should exist.
OK
ENG
Repair harness.
Ref. part No. C4
qA
YEL471B
YEL322D
YEL323D
YEL324D
YEL325D
H
H
H
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-199

qA
CHECK COMMUNICATION LINE SHORT
CIRCUIT.
1. Disconnect ECM connector and IMMU
connector.
2. Check continuity between IMMU termi-
nalq
1and ground.
Continuity should not exist.
3. Turn ignition switch to ON.
4. Check voltage between IMMU terminal
q
1and ground.
No voltage should exist.
OK
ENG
Repair harness.
Ref. part No. C4
Check the signal from ECM to IMMU.
1. Check the signal between ECM termi-
nal
410(ZD30DDTi models) orq55
(TD27Ti models) and ground with
CONSULT-II or oscilloscope when igni-
tion switch is turned ON.
2. Some signals can be detected during
750 msec. just after ignition switch is
turned ªONº.
OK
ENG
ECM is malfunctioning.
1. Replace ECM.
Ref part No. B
2. Perform initialization
procedure, refer to
ªCONSULT-II operation
manual NATSº.
IMMU is malfunctioning.
1. Replace IMMU.
Ref. part No. A
2. Perform initialization with CONSULT-II.
For the initialization procedure, refer to
ªCONSULT-II operation manual NATSº.
YEL326D
NEL543
H
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-200

DIAGNOSTIC PROCEDURE 3
Self-diagnostic results:
ªDIFFERENCE OF KEYº displayed on CONSULT-II screen
Confirm SELF-DIAGNOSTIC
RESULTS ªDIFFERENCE OF KEYº
displayed on CONSULT-II screen.
OK
PERFORM INITIALISATION.
Perform initialisation with CONSULT-II.
Re-register all NATS ignition key IDs.
For the initialisation procedure, refer to
ªCONSULT-II operation manual NATSº.
Can the system be initialized?
Note: If the initialisation is not completed
or fails, CONSULT-II shows
message on the screen.
Ye s
ENo
IIMMU is malfunctioning.
1. Replace IMMU.
Ref. part No. A
2. Perform initialisation
with CONSULT-II.
For the initialisation
procedure, refer to
ªCONSULT-II operation
manual NATSº.
Start engine.
END
(Ignition key ID had been unregistered.)
YEL478B
YEL479B
H
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-201

DIAGNOSTIC PROCEDURE 4
Self-diagnostic results:
ªCHAIN OF IMMU-KEYº displayed on CONSULT-II screen
Confirm SELF-DIAGNOSTIC
RESULTS ªCHAIN OF IMMU-KEYº
displayed on CONSULT-II screen.
OK
CHECK NATS IGNITION KEY ID CHIP.
Can the engine start with another regis-
tered NATS ignition key?
No
EYe s
IIgnition key ID chip is
malfunctioning.
1. Replace the ignition
key.
Ref. part No. E
2. Perform initialisation
with CONSULT-II.
For the initialisation
procedure, refer to
ªCONSULT-II operation
manual NATSº.
CHECK NATS IMMU INSTALLATION.
Refer to ªHow to Replace NATS IMMUº in
EL-208.
OK
ENG
Reinstall NATS IMMU cor-
rectly.
Is this vehicle equipped with dongle con-
trol unit (RHD models)?
Ye s
ENo
IMMU is malfunctioning.
1. Replace IMMU.
Ref part No. A
2. Perform initialisation
with CONSULT-II
For the initialisation
procedure, refer to
ªCONSULT-II operation
manual NATSº.
qA
YEL480B
H
H
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-202

qA
CHECK HARNESS CONNECTOR CON-
NECTION.
Check the following harness connector
connection.
M720
Does the engine start?
No
EYe s
System is OK.
(The malfunction is caused
by improper connector
connection.)
CHECK GROUND CIRCUIT FOR
DONGLE UNIT.
Check continuity between dongle control
unit terminalq
3and ground.
Continuity should exist.
Ye s
ENo
Repair harness.
CHECK INTERFACE CIRCUIT.
1. Check continuity between IMMU termi-
nalq
2and dongle control unit terminal
q
5(Open circuit check)
Continuity should exist.
2. Check continuity between IMMU termi-
nalq
2and ground. (Short circuit check)
Continuity should not exist.
Ye s
ENo
Repair harness.
Dongle unit is malfunctioning.
1. Replace dongle control unit.
2. Perform initialisation with CONSULT-II.
For the initialisation procedure, refer to
ªCONSULT-II operation manual NATSº.
YEL327D
YEL328D
YEL329D
H
H
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-203

DIAGNOSTIC PROCEDURE 5
Self-diagnostic results:
ªID DISCORD, IMM-ECMº displayed on CONSULT-II screen
Confirm SELF-DIAGNOSTIC
RESULTS ªID DISCORD, IMM-
ECM*º displayed on CONSULT-II
screen.* ªID DISCORD, IMM-ECMº:
Registered ID of IMMU is in
discord with that of ECM.
PERFORM INITIALISATION.
Perform initialisation with CONSULT-II.
Re-register all NATS ignition key IDs.
For the initialisation procedure, refer to
ªCONSULT-II operation manual NATSº.
Can the system be initialized?
Note: If the initialisation is not com-
pleted or fails, CONSULT-II shows
message on the screen.
Ye s
ENo
IECM is malfunctioning.
1. Replace ECM.
Ref. part No. B
2. Perform initialisation
with CONSULT-II.
For the initialisation
procedure, refer to
ªCONSULT-II operation
manual NATSº.
Start engine. (END)
(System initialisation was not completed.
Ref. part No. F)
C2SDD01
YEL479B
H
H
NATS (Nissan Anti-Theft System)
Trouble Diagnoses (Cont'd)
EL-204