cr with euro obd NISSAN TIIDA 2007 Service Repair Manual

INSPECTION AND ADJUSTMENT
BRC-11
< BASIC INSPECTION >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
>> GO TO 2
2.PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1. On the CONSULT-III screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0±2.5°.
Is the steering angle within the specified range?
YES >> GO TO 4
NO >> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
 ABS actuator and electric unit (control unit): Refer to BRC-25, "
CONSULT-III Function (ABS)".
 ECM, refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
Are the memories erased?
YES >> INSPECTION END
NO >> Check the items indicated by the self-diagnosis.
CALIBRATION OF DECEL G SENSOR
CALIBRATION OF DECEL G SENSOR : DescriptionINFOID:0000000001731357
Refer to the table below to determine if calibration of the decel G sensor is required.
×: Required –: Not required
Situation Calibration of decel G sensor
Removing/Installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit)×
Removing/Installing steering angle sensor×
Replacing steering angle sensor×
Removing/Installing steering components×
Replacing steering components×
Removing/Installing suspension components×
Replacing suspension components×
Change tires to new ones—
Tire rotation—
Adjusting wheel alignment×

BRC-12
< BASIC INSPECTION >[ABS]
INSPECTION AND ADJUSTMENT
CALIBRATION OF DECEL G SENSOR : Special Repair Requirement
INFOID:0000000001731358
CALIBRATION OF DECEL G SENSOR
CAUTION:
To calibrate the decel G sensor, make sure to use CONSULT-III
(Calibration cannot be done without CONSULT-III)
1.ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2
2.PERFORM CALIBRATION OF DECEL G SENSOR
1. On the CONSULT-III screen, touch “WORK SUPPORT” and “DECEL G SEN CALIBRATION” in order.
2. Touch “START”.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “DECEL G SEN” is within ±.
Is the inspection result normal?
YES >> GO TO 4
NO >> Perform calibration of decel G sensor again, GO TO 1
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
 ABS actuator and electric unit (control unit): Refer to BRC-25, "
CONSULT-III Function (ABS)".
 ECM, refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
Are the memories erased?
YES >> INSPECTION END
NO >> Check the items indicated by the self-diagnosis.

BRC-52
< COMPONENT DIAGNOSIS >[ABS]
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
DescriptionINFOID:0000000001731271
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication
line.
DTC LogicINFOID:0000000001731272
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-52, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000001731273
INSPECTION PROCEDURE
1.CHECK ENGINE SYSTEM
1. Perform ECM self-diagnosis. Repair or replace items indicated, then perform ECM self-diagnosis again.
Refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
2. Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-25, "
CONSULT-III Func-
tion (ABS)".
Is any item indicated on the self-diagnosis display?
YES >> Repair or replace the affected part.
NO >> INSPECTION END
Special Repair RequirementINFOID:0000000001731274
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
DTC Display item Malfunction detected condition Possible cause
C1130 ENGINE SIGNAL 1
Based on the signal from ECM, ABS actuator and electric
unit (control unit) judges that engine fuel cut system is
malfunctioning. Harness or connector
 ABS actuator and electric unit
(control unit)
ECM
 CAN communication line C1131 ENGINE SIGNAL 2
C1132 ENGINE SIGNAL 3
C1133 ENGINE SIGNAL 4
C1136 ENGINE SIGNAL 6
Self-diagnosis results
ENGINE SIGNAL 1
ENGINE SIGNAL 2
ENGINE SIGNAL 3
ENGINE SIGNAL 4
ENGINE SIGNAL 6

INSPECTION AND ADJUSTMENT
BRC-91
< BASIC INSPECTION >[ESP/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
>> GO TO 2
2.PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1. On the CONSULT-III screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0±2.5°.
Is the steering angle within the specified range?
YES >> GO TO 4
NO >> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
 ABS actuator and electric unit (control unit): Refer to BRC-25, "
CONSULT-III Function (ABS)".
 ECM, refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
Are the memories erased?
YES >> INSPECTION END
NO >> Check the items indicated by the self-diagnosis.
CALIBRATION OF DECEL G SENSOR
CALIBRATION OF DECEL G SENSOR : DescriptionINFOID:0000000001731365
Refer to the table below to determine if calibration of the decel G sensor is required.
×: Required –: Not required
Situation Calibration of decel G sensor
Removing/Installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit)×
Removing/Installing steering angle sensor×
Replacing steering angle sensor×
Removing/Installing steering components×
Replacing steering components×
Removing/Installing suspension components×
Replacing suspension components×
Change tires to new ones—
Tire rotation—
Adjusting wheel alignment×

BRC-92
< BASIC INSPECTION >[ESP/TCS/ABS]
INSPECTION AND ADJUSTMENT
CALIBRATION OF DECEL G SENSOR : Special Repair Requirement
INFOID:0000000001731366
CALIBRATION OF DECEL G SENSOR
CAUTION:
To calibrate the decel G sensor, make sure to use CONSULT-III
(Calibration cannot be done without CONSULT-III)
1.ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2
2.PERFORM CALIBRATION OF DECEL G SENSOR
1. On the CONSULT-III screen, touch “WORK SUPPORT” and “DECEL G SEN CALIBRATION” in order.
2. Touch “START”.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “DECEL G SEN” is within ±.
Is the inspection result normal?
YES >> GO TO 4
NO >> Perform calibration of decel G sensor again, GO TO 1
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
 ABS actuator and electric unit (control unit): Refer to BRC-25, "
CONSULT-III Function (ABS)".
 ECM, refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
Are the memories erased?
YES >> INSPECTION END
NO >> Check the items indicated by the self-diagnosis.

C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
BRC-135
< COMPONENT DIAGNOSIS >[ESP/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
DescriptionINFOID:0000000001731128
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication
line.
DTC LogicINFOID:0000000001731129
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-52, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000001731130
INSPECTION PROCEDURE
1.CHECK ENGINE SYSTEM
1. Perform ECM self-diagnosis. Repair or replace items indicated, then perform ECM self-diagnosis again.
Refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
2. Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-25, "
CONSULT-III Func-
tion (ABS)".
Is any item indicated on the self-diagnosis display?
YES >> Repair or replace the affected part.
NO >> INSPECTION END
Special Repair RequirementINFOID:0000000001731131
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
DTC Display item Malfunction detected condition Possible cause
C1130 ENGINE SIGNAL 1
Based on the signal from ECM, ABS actuator and electric
unit (control unit) judges that engine fuel cut system is
malfunctioning. Harness or connector
 ABS actuator and electric unit
(control unit)
ECM
 CAN communication line C1131 ENGINE SIGNAL 2
C1132 ENGINE SIGNAL 3
C1133 ENGINE SIGNAL 4
C1136 ENGINE SIGNAL 6
Self-diagnosis results
ENGINE SIGNAL 1
ENGINE SIGNAL 2
ENGINE SIGNAL 3
ENGINE SIGNAL 4
ENGINE SIGNAL 6

VEHICLE JERKS DURING VDC/TCS/ABS CONTROL
BRC-177
< SYMPTOM DIAGNOSIS >[ESP/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
VEHICLE JERKS DURING VDC/TCS/ABS CONTROL
Diagnosis ProcedureINFOID:0000000001731206
1.SYMPTOM CHECK
Check if the vehicle jerks during VDC/TCS/ABS control.
Is the inspection result normal?
YES >> Normal.
NO >> GO TO 2
2.CHECK SELF-DIAGNOSIS RESULTS
Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to BRC-25, "
CONSULT-III Func-
tion (ABS)".
Are self-diagnosis results indicated?
YES >> Check corresponding items, make repairs, and perform ABS actuator and electric unit (control
unit) self-diagnosis.
NO >> GO TO 3
3.CHECK CONNECTOR
 Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector and check
terminal for deformation, disconnection, looseness, etc.
 Securely connect connectors and perform ABS actuator and electric unit (control unit) self-diagnosis.
Are self-diagnosis results indicated?
YES >> If poor contact, damage, open or short circuit of connector terminal is found, repair or replace.
NO >> GO TO 4
4.CHECK ECM AND TCM SELF-DIAGNOSIS RESULTS
Perform ECM and TCM self-diagnosis.
Are self-diagnosis results indicated?
YES >> Check the corresponding items.
 ECM, refer to:
-EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD)
-EC-462, "
CONSULT-III Function" (HR16DE without EURO-OBD)
-EC-772, "
CONSULT-III Function" (MR18DE)
-EC-1104, "
Diagnosis Description" (K9K)
 TCM, refer to:
-TM-35, "
CONSULT-III Function (TRANSMISSION)" (4AT:RE4F03B type 1)
-TM-348, "
CONSULT-III Function (TRANSMISSION)" (4AT:RE4F03B type 2)
-TM-620, "
System Description" (RS5F91R)
-TM-664, "
System Description" (6MT: RS6F94R)
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-184, "
Removal and Installa-
tion".

CCS-2
< FUNCTION DIAGNOSIS >
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
FUNCTION DIAGNOSIS
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
DescriptionINFOID:0000000001723096
HR16DE (WITH EURO-OBD)
For information regarding the ASCD system, refer to EC-61, "System Description" .
HR16DE (WITHOUT EURO-OBD)
For information regarding the ASCD system, refer to EC-424, "System Description" .
MR18DE
For information regarding the ASCD system, refer to EC-728, "System Description" .

EC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
N
O
P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE (WITH EURO-OBD)
BASIC INSPECTION ...................................
18
DIAGNOSIS AND REPAIR WORKFLOW .........18
Work Flow ...............................................................18
Diagnostic Work Sheet ............................................20
INSPECTION AND ADJUSTMENT ....................22
BASIC INSPECTION .................................................22
BASIC INSPECTION : Special Repair Require-
ment ........................................................................
22
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ........................................................
25
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ................................
25
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .....
25
IDLE SPEED ..............................................................25
IDLE SPEED : Description ......................................26
IDLE SPEED : Special Repair Requirement ...........26
IGNITION TIMING ......................................................26
IGNITION TIMING : Description ..............................26
IGNITION TIMING : Special Repair Requirement ....26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ................................................................
26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .........................................
26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ..............
26
THROTTLE VALVE CLOSED POSITION LEARN-
ING .............................................................................
27
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .........................................
27
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ..............
27
IDLE AIR VOLUME LEARNING ................................27
IDLE AIR VOLUME LEARNING : Description .........27
IDLE AIR VOLUME LEARNING : Special Repair
Requirement ............................................................
27
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR .......................................................................
29
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Description ................................................
29
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Special Repair Requirement .....................
29
FUNCTION DIAGNOSIS ..............................30
ENGINE CONTROL SYSTEM ..........................30
System Diagram .....................................................30
System Description ..................................................31
Component Parts Location ....................................31
Component Description ...........................................36
MULTIPORT FUEL INJECTION SYSTEM .......38
System Diagram .....................................................38
System Description ..................................................38
Component Parts Location ....................................41
Component Description ...........................................46
ELECTRIC IGNITION SYSTEM ........................47
System Diagram .....................................................47
System Description ..................................................47
Component Parts Location ....................................48
Component Description ...........................................53
AIR CONDITIONING CUT CONTROL ..............54
System Diagram ......................................................54
System Description ..................................................54
Component Parts Location ....................................55
Component Description ...........................................60
AUTOMATIC SPEED CONTROL DEVICE
(ASCD) ..............................................................
61
System Diagram ......................................................61
System Description ..................................................61

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P Component Function Check ..................................
316
Diagnosis Procedure .............................................316
Component Inspection (Fuel Pump) .....................318
IGNITION SIGNAL ...........................................319
Description ............................................................319
Component Function Check ..................................319
Diagnosis Procedure .............................................319
Component Inspection (Ignition Coil with Power
Transistor) .............................................................
322
Component Inspection (Condenser) .....................322
MALFUNCTION INDICATOR ...........................324
Description ............................................................324
Component Function Check ..................................324
Diagnosis Procedure .............................................324
POSITIVE CRANKCASE VENTILATION ........325
Description ............................................................325
Component Inspection ..........................................325
REFRIGERANT PRESSURE SENSOR ...........326
Description ............................................................326
Component Function Check ..................................326
Diagnosis Procedure .............................................326
ECU DIAGNOSIS .......................................328
ECM ..................................................................328
Reference Value ...................................................328
Wiring Diagram - ENGINE CONTROL SYSTEM - ..339
Fail Safe ...............................................................358
DTC Inspection Priority Chart .............................360
DTC Index ............................................................361
How to Set SRT Code ........................................363
Test Value and Test Limit ..................................365
SYMPTOM DIAGNOSIS ............................366
ENGINE CONTROL SYSTEM SYMPTOMS ....366
Symptom Table .....................................................366
NORMAL OPERATING CONDITION ...............370
Description ............................................................370
PRECAUTION ............................................371
PRECAUTIONS ................................................371
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
371
Precaution for Procedure without Cowl Top Cover ..371
Precautions For Xenon Headlamp Service ...........371
On Board Diagnostic (OBD) System of Engine
and A/T ..................................................................
372
General Precautions .............................................372
PREPARATION .........................................375
PREPARATION ................................................375
Special Service Tools ............................................375
Commercial Service Tools ....................................375
ON-VEHICLE MAINTENANCE ..................377
FUEL PRESSURE ...........................................377
Inspection ..............................................................377
EVAPORATIVE EMISSION SYSTEM .............379
Inspection ..............................................................379
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
380
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
380
Idle Speed .............................................................380
Ignition Timing .......................................................380
Calculated Load Value ..........................................380
Mass Air Flow Sensor ............................................380
HR16DE (WITHOUT EURO-OBD)
BASIC INSPECTION .................................
381
DIAGNOSIS AND REPAIR WORKFLOW ......381
Work Flow ..............................................................381
Diagnostic Work Sheet ..........................................383
INSPECTION AND ADJUSTMENT ................385
BASIC INSPECTION ...............................................385
BASIC INSPECTION : Special Repair Require-
ment .......................................................................
385
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ...............................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement ....
388
IDLE SPEED ............................................................388
IDLE SPEED : Description ....................................389
IDLE SPEED : Special Repair Requirement .........389
IGNITION TIMING ....................................................389
IGNITION TIMING : Description ............................389
IGNITION TIMING : Special Repair Requirement ..389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ...............................................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .......................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ............
389
THROTTLE VALVE CLOSED POSITION LEARN-
ING ...........................................................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .......................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ............
390
IDLE AIR VOLUME LEARNING ..............................390
IDLE AIR VOLUME LEARNING : Description .......390