NISSAN VERSA 2006 Workshop Service Repair Manual

FRONT SEAT
SE-13
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: June 20062007 Versa
3. Remove seat cushion trim and seat cushion pad from the seat cushion frame.
Assembly
Assembly is the reverse order of removal.
SEAT CUSHION FRAME
Disassembly
1. Remove the seat cushion trim and pad. Refer to SE-12, "SEAT CUSHION TRIM AND PAD" .
2. Remove the seat cushion finisher B. (Driver seat)
3. Remove the seat cushion lower finisher.
4. Remove the front seat belt buckle.
Assembly
Assembly is the reverse order of removal.
PIIB2607E
PIIB2609E

SE-14
REAR SEAT
Revision: June 20062007 Versa
REAR SEATPFP:88300
Component Parts DrawingEIS0097N
60:40 SPLIT FOLD DOWN SEAT
WIIA1231E

REAR SEAT
SE-15
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: June 20062007 Versa
Removal and InstallationEIS0097O
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
60:40 SPLIT FOLD DOWN SEAT
Removal
1. Pull seat cushion up, and then remove the seat cushion from the
seat cushion hook.
2. Remove the center seatbelt anchor bolt from under the seat.
3. Remove the seatback mounting bolts from the right rear seat
back brackets.
1. Seat cushion trim 2. Seat cushion pad 3. Seatback side
4. Armrest 5. Rear seat bushing 6. Armrest hinge cover
7. Headrest 8. Headrest holder (free) 9. Headrest holder (locked)
10. Striker cover 11. Seatback trim 12. Seatback pad
13. Rear seatback lock knob 14. Rear seat lock assembly 15. Seatback frame
16. Rear seatback center bracket 17. Rear seatback side bracket 18. Rear seat striker
19. Seat cushion hook 20. Center seat belt assembly
PIIB4085J
WIIA1234E
WIIA1287E

SE-16
REAR SEAT
Revision: June 20062007 Versa
4. Remove the seatback mounting bolts from the left rear seat
back brackets.
5. Remove the seatback from the vehicle.
6. Remove the kicking plate rear inner. Refer to EI-32, "
Removal and Installation" .
7. Remove the bolt under the seatback side.
8. Pull seatback side up, and then remove seatback side.
9. Remove the bolts, and then remove rear seatback center bracket.
10. Remove the bolt, and then remove rear seatback side bracket
from the vehicle.
11. Remove the rear seatback finisher. Refer to EI-42, "
Removal and Installation" .
12. Remove the bolts, and then remove the rear seat striker.
Installation
Installation is the reverse order of removal. Be careful of the following point.

Seatback assembly and rear seatback side bracket installation procedure.
WIIA1288E
PIIB2482J
PIIB2483J
PIIB2484J

REAR SEAT
SE-17
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: June 20062007 Versa
1. Install the rear seatback side bracket in the vehicle.
2. Temporarily tighten the seatback assembly and rear seatback side bracket.
3. Lift to fold up seatback assembly. Be sure to lock seatback assembly to rear seat striker.
4. Tighten the bolt.
NOTE:
Confirm that side hinge bracket location pin is set to the hole on the seatback backside.
Disassembly and AssemblyEIS0097P
60:40 SPLIT FOLD DOWN SEAT
Disassembly of Armrest
1. Fold up the backside of the seatback trim and then remove the
armrest nuts.
2. Push the armrest toward left side while pulling backward to
remove.
3. Remove the rear seat bushing, and then remove the armrest
hinge cover by pulling it backward.
PIIB2484J
PIIB2913J
PIIB2915J
PIIB6507E

SE-18
REAR SEAT
Revision: June 20062007 Versa
Assembly of Armrest
Assembly in the reverse order of disassembly.
Disassembly of Seatback Trim and Pad
1. Remove the headrest.
2. Remove the retainer under the back of seatback.
3. Remove the clips, and then remove the striker cover.
4. Remove the headrest holder.
5. To remove armrest, refer to SE-17, "
Disassembly of Armrest" .
6. Remove the seatback trim.
7. Remove the bolts, and then remove the rear seat lock assembly.
8. Remove the seatback pad from the seatback frame.
9. Remove the seatback center bracket bolt and then remove the seatback frame.
PIIB2486J
PIIB2485J
PIIB4084J
PIIB2487J

REAR SEAT
SE-19
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: June 20062007 Versa
Assembly of Seatback Trim and Pad
Assembly is the reverse order of disassembly. Be careful of the following one point.

Before installing headrest holder, check its orientation (front/rear and right/left).
Disassembly of Seat Cushion Trim and Pad
Remove the rings to separate the trim and pad.
Assembly of Seat Cushion Trim and Pad
Assembly is the reverse order of disassembly.

SE-20
REAR SEAT
Revision: June 20062007 Versa

SRS-1
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
H RESTRAINTS
CONTENTS
C
D
E
F
G
I
J
K
L
M
SECTION SRS
A
B
SRS
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for SRS “AIR BAG” and “SEAT BELT
PRE-TENSIONER” Service ..................................... 3
Occupant Classification System Precaution ............ 3
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) ....... 4
SRS Configuration ................................................... 4
Driver Air Bag Module .............................................. 5
Front Passenger Air Bag Module ............................. 5
Front Side Air Bag .................................................... 5
Side Curtain Air Bag ................................................. 5
Front Seat Belt Pre-tensioner with Load Limiter ...... 6
Occupant Classification System (OCS) ................... 6
Direct-connect SRS Component Connectors ........... 8
TROUBLE DIAGNOSIS .............................................. 9
Trouble Diagnosis Introduction ................................. 9
DIAGNOSIS FUNCTION ....................................... 9
HOW TO PERFORM TROUBLE DIAGNOSES
FOR QUICK AND ACCURATE REPAIR ............... 9
WORK FLOW ...................................................... 10
SRS Components Parts Location ............................11
Schematic .............................................................. 12
Wiring Diagram — SRS — ..................................... 13
CONSULT-II Function (AIR BAG) ........................... 19
HOW TO CHANGE BETWEEN SELF-DIAGNO-
SIS MODE AND USER MODE WITH CONSULT-
II .......................................................................... 19
HOW TO ERASE SELF-DIAGNOSIS RESULTS ... 20
Self-Diagnosis Function (Without CONSULT-II) ..... 20
HOW TO CHANGE BETWEEN USER MODE
AND SELF-DIAGNOSIS MODE WITHOUT
CONSULT-II ........................................................ 21
HOW TO ERASE SELF-DIAGNOSIS RESULTS ... 21
SRS Operation Check ............................................ 21
DIAGNOSTIC PROCEDURE 1 ........................... 21
Trouble Diagnosis With CONSULT-II ..................... 23
DIAGNOSTIC PROCEDURE 2 ........................... 23DIAGNOSTIC PROCEDURE 3 ........................... 27
DIAGNOSTIC PROCEDURE 4 ........................... 29
DIAGNOSTIC PROCEDURE 5 ........................... 29
Trouble Diagnosis Without CONSULT-II ................. 34
DIAGNOSTIC PROCEDURE 6 ........................... 34
WARNING LAMP FLASH CODE CHART ........... 35
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn Off ............................................................ 39
DIAGNOSTIC PROCEDURE 7 ........................... 39
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn On ............................................................ 40
DIAGNOSTIC PROCEDURE 8 ........................... 40
DRIVER AIR BAG MODULE .................................... 41
Removal and Installation ........................................ 41
REMOVAL ........................................................... 41
INSTALLATION ................................................... 42
SPIRAL CABLE ........................................................ 44
Removal and Installation ........................................ 44
REMOVAL ........................................................... 44
INSTALLATION ................................................... 45
FRONT PASSENGER AIR BAG MODULE .............. 46
Removal and Installation ........................................ 46
REMOVAL ........................................................... 46
INSALLATION ..................................................... 46
SIDE CURTAIN AIR BAG MODULE ........................ 47
Removal and Installation ........................................ 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 48
CRASH ZONE SENSOR ........................................... 49
Removal and Installation ........................................ 49
REMOVAL ........................................................... 49
INSTALLATION ................................................... 49
SIDE AIR BAG (SATELLITE) SENSOR ................... 50
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION ................................................... 50
FRONT SEAT BELT PRE-TENSIONER ................... 51
Removal and Installation ........................................ 51

SRS-2Revision: June 20062007 Versa DIAGNOSIS SENSOR UNIT ..................................... 52
Removal and Installation ........................................ 52
REMOVAL ........................................................... 52
INSTALLATION .................................................... 52
ECU DISCRIMINATED NO. ................................. 52
OCCUPANT CLASSIFICATION SYSTEM CON-
TROL UNIT ................................................................ 53
Removal and Installation ........................................ 53
COLLISION DIAGNOSIS .......................................... 54
For Frontal Collision ................................................ 54SRS INSPECTION (FOR FRONTAL COLLI-
SION) ...................................................................54
For Side and Rollover Collision ...............................55
WHEN SRS IS ACTIVATED IN THE SIDE OR
ROLLOVER COLLISION .....................................55
WHEN SRS IS NOT ACTIVATED IN THE SIDE
OR ROLLOVER COLLISION ...............................55
SRS INSPECTION (FOR SIDE AND ROLLOVER
COLLISION) .........................................................56