NISSAN X-TRAIL 2003 Service Repair Manual

REAR DOOR GLASS AND REGULATOR
GW-85
C
D
E
F
G
H
J
K
L
MA
B
GW

16. Remove regulator assembly and the guide rail mounting bolts
through the access hole.
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER REMOVAL
Check regulator assembly for the following items. If a malfunction is
detected, replace or grease it.

Gear wear

Regulator deformation

Spring damage

Grease condition for each sliding part
The arrows in the figure show body grease application points of the
grease “Dow Corning Moly Coat SK 623” or equivalent.
FITTING INSPECTION

Check that glass is securely fit into glass run groove.

While raising and lowering the window, check for abnormal operation.

Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the sash
is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass & carrier plate mounting bolts to correct the glass position.
PIIA0556E
OCC3565D

GW-86
DOOR MIRROR

DOOR MIRRORPFP:96301
Precautions to Handle Retractable Power Door MirrorsEIS004JO

Do not manually operate retractable power door mirrors. If mirror
is operated manually, be sure to use the retracting switch to
move mirror fully to the opposite direction until it stops. In this
case, a loud click sound is heard, but it is not abnormal. (If mirror
body is manually moved to the neutral position, door mirror will
have some disturbing symptoms during driving, including vibra-
tion, rough retracting movement, or sometimes no retracting.)
CAUTION:
Tilting mirror body forward with excessive force may dam-
age it.

When operating retracting switch to move mirror from the neu-
tral position to the fully-closed (backward limit) position, at the
beginning of the movement a faint click sound is heard, but it is not abnormal.

RH and LH retractable power door mirror bodies have different mounting angles in the neutral position.
This is why the RH mirror body delays slightly when operated with the retracting switch.
NOTE:

When the retractable power door mirror body is in the neutral
position, if retracting switch is operated to the opening direc-
tion while pressing it forward, mirror body is moved to the for-
ward limit position, but it is not abnormal. In this case, be sure
to operate retracting switch to move mirror to the fully-closed
(backward limit) position.

When the retracting switch is operated continuously 5 times
or more, the retractable power door mirror may be inactivated
to prevent overheating. In this case, wait for approximately 5
minutes to recover.
PIIA0513E
PIIA0514E

DOOR MIRROR
GW-87
C
D
E
F
G
H
J
K
L
MA
B
GW

Wiring Diagram — MIRROR — / For LHD modelsEIS004JP
TIWA0458E

GW-88
DOOR MIRROR

TIWA0459E

DOOR MIRROR
GW-89
C
D
E
F
G
H
J
K
L
MA
B
GW

Wiring Diagram — MIRROR — / For RHD modelsEIS004JQ
TIWA0460E

GW-90
DOOR MIRROR

TIWA0461E

DOOR MIRROR
GW-91
C
D
E
F
G
H
J
K
L
MA
B
GW

Removal and InstallationEIS004JR
REMOVAL
1. Remove front door finisher. Refer to EI-32, "Removal and Installation" .
2. Remove corner cover.
3. Remove door mirror harness connector.
4. Remove door mirror mounting nuts, and remove door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
1. Door mirror 2. Connector 3. Corner cover
SIIA0186E

GW-92
DOOR MIRROR

Disassembly and AssemblyEIS004JS
DISASSEMBLY
1. Pull out all the terminals from the connector.
NOTE:
Before pulling out the terminal, note the connector terminal arrangement.
2. Turn the mirror glass surface upward.
3. Apply a protective tape to the housing.
4. Insert a narrow slotted screwdriver in the concave gap between mirror glass and power unit to push up
tabs (2 locations) on mirror holder to disengage lower part of mirror holder, and remove mirror body
assembly.
NOTE:
When pushing up the tabs, do not forcefully push up only 1 concave but try to push up using 2 concave
positions.
5. Remove packing.
6. Remove base.
7. Remove electric retracting unit.
8. Remove power unit, and disconnect the connector.
9. Separate the electric retracting unit from the bracket.
1. Mirror body 2. Power unit 3. Bracket
4. Electric retracting unit 5. Housing 6. Base
7. Packing 8. Connector
SIIA0187E

DOOR MIRROR
GW-93
C
D
E
F
G
H
J
K
L
MA
B
GW

ASSEMBLY
1. Install bracket to the electric retracting unit.
2. Connect power unit connector. Install electric retracting unit (bracket).
3. Install electric retracting unit and base to the housing.
4. Place power unit and mirror body assembly in a horizontal position.
5. Engage upper tabs of mirror glass with power unit. Then, press lower part of mirror glass down until the
lower part snaps to allow engagement of lower tabs.
NOTE:
After installation, visually check that the lower tabs (2) are securely engaged when viewed from the bot-
tom of mirror surface.
6. Install the packing to the base.
7. Insert the harness terminal into the connector.
NOTE:
Make sure to insert the harness terminal into the correct connector. Do not confuse the locations.

GW-94
INSIDE MIRROR

INSIDE MIRRORPFP:96321
Removal and InstallationEIS008O4
REMOVAL
Remove the screws securing inside mirror assembly and mirror base
as shown in the figure.
INSTALLATION
Install in the reverse order of removal.
SIIA1024E