NISSAN X-TRAIL 2003 Service Repair Manual

REAR COMBINATION LAMP
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in "EI EXTERIOR & INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
PKIA8620E
Rear combination lamp mounting bolts
Tightening torque
: 5.4 N·m (0.55 kg-m, 48 in-lb)

LT-64
COMBINATION SWITCH

COMBINATION SWITCHPFP:25567
Removal and InstallationEKS001V6
Refer to SRS-33, "SPIRAL CABLE" in "SUPPLEMENTAL RESTRAINT SYSTEM (SRS)" section for details.
Switch Circuit InspectionEKS001V7
Refer to LT- 4 0 , "Switch Circuit Inspection" in "LIGHTING AND TURN SIGNAL SWITCH" section, and WW-8,
"Terminal and Reference Values for Combination Switch" , WW-16, "Terminal and Reference Values for Com-
bination Switch" in “WW Wiper/Washer Horn” section for details.

ASHTRAY ILLUMINATION
LT-65
C
D
E
F
G
H
I
J
L
MA
B
LT

ASHTRAY ILLUMINATIONPFP:25860
Bulb Replacement, Removal and InstallationEKS00F86
1. Remove the instrument center lower panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" in “IP” section.
2. Turn bulb socket counterclockwise and unlock it.
3. Pull the bulb from socket.
4. Install in the reverse order of removal.Ashtray illumination lamp : 12V - 1.4W
PKIA6440E

LT-66
ILLUMINATION

ILLUMINATIONPFP:27545
System Description EKS003C7
Power is supplied at all times

through 10A fuse [No. 31, located in the fuse and fusible link box]

to lighting switch terminal 11.
The lighting switch must be in the 1ST or 2ND position for illumination.
The following chart shows the power and ground connector terminals for the components included in the illu-
mination system.
Component Connector No. Power terminal Ground terminal
Headlamp washier switch M23 3 4
Headlamp aiming switch M24 3 4
Door mirror remote control switch M26 10 1
ESP off switch M25 3 4
Hazard switch M51 7 8
4WD mode switch M39 4 3
Rear window defogger switch M50 5 6
A/C auto amp. M52 12 11
Combination meter (LHD models) M46 56 66
Combination meter (RHD models) M46 45 56
Audio M42 2 1
CD auto changer M82 34 35
Heater control panel M55 2 6
A/T device M58 3 4
Cigarette lighter M56 3 2
Heated seat switch LH (LHD models) B131 5 6
Heated seat switch RH (LHD models) B132 5 6
Heated seat switch LH (RHD models) B35 5 6
Heated seat switch RH (RHD models) B34 5 6

ILLUMINATION
LT-67
C
D
E
F
G
H
I
J
L
MA
B
LT

SchematicEKS003BL
TKWA1538E

LT-68
ILLUMINATION

Wiring Diagram -ILL-EKS003BM
LHD MODELS
TKWA1539E

ILLUMINATION
LT-69
C
D
E
F
G
H
I
J
L
MA
B
LT

TKWA1540E

LT-70
ILLUMINATION

TKWA1541E

ILLUMINATION
LT-71
C
D
E
F
G
H
I
J
L
MA
B
LT

TKWA1542E

LT-72
ILLUMINATION

RHD MODELS
TKWA1543E