Oldsmobile Intrigue 2000 Owner's Manuals

2-33
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control.
Don't use cruise control on slippery roads.
If your vehicle is in cruise control when the optional
traction control system begins to limit wheel spin,
the cruise control will automatically disengage.
(See ªTraction Control Systemº in the Index.)
When road conditions allow you to safely use it again,
you may turn the cruise control back on.Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE
button on the right side
of the instrument panel
to turn it on. A light on
the button will indicate
that the system is on.

2-34
2. Get up to the speed you want.
3. Press the COAST SET
button on your steering
wheel and release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RES ACCEL
button on your steering
wheel. You'll go right back
up to your chosen speed and
stay there.

2-35
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button on the steering wheel,
then release the button and the accelerator pedal.
You'll now cruise at the higher speed.

Press the RES ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the button. (To increase your speed
in very small amounts, press the RES ACCEL button
briefly and then release it. Each time you do this,
your vehicle will go 1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
on the steering wheel.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button on the steering wheel
until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button on the steering wheel briefly
and then release it. Each time you do this, you'll
go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.

2-36
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lamp controls are located on the multifunction lever on
the left of the steering wheel. They control these systems:

Headlamps

Taillamps

Parking Lamps

License Lamps

Sidemarker Lamps

Instrument Panel Lights

2-37
: Turn the end of the lever to this symbol to turn on
the headlamps and other operating lamps.
: Turn the end of the lever to this symbol to
turn on the parking and other operating lamps without
the headlamps.
Turn the end of the lever to OFF to turn off the lamps.
A warning chime will sound if you open the driver's
door when you turn the ignition switch to OFF or ACC
with the lamps on.
Daytime Running Lamps / Automatic
Headlamp Control
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn't covered.
The DRL system will make your front turn signal lamps
come on when:

The ignition is on,
the headlamp switch is off and

the parking brake is released.
When the DRL are on, only your front turn signal lamps
will be on. The headlamps, taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When it's dark enough outside, your front turn signal
lamps will turn off and your headlamps and parking
lamps will turn on.
When it's bright enough outside, your headlamps will go
off and your front turn signal lamps will come on.
To idle your vehicle with the DRL or automatic
headlamps off, set the parking brake while the ignition is
in OFF. Then start your vehicle. The DRL, headlamps
and parking lamps will stay off until you release the
parking brake.
To turn off the automatic headlamp feature when it's
dark outside, move the exterior lamp control to the
parking lamp position. Your parking lamps will remain
illuminated and your headlamps will turn off. The fog
lamps (if equipped) will also be lit if they were on when
you switched to the parking lamp position.
As with any vehicle, you should turn on the regular
headlamp system when you need it.

2-38 Fog Lamps
To turn the fog lamps on,
press the top of the fog
lamp switch located on
the left side of the
instrument panel.
A light will glow on the switch to let you know that they
are on. Please note that your parking lamps must be on
or your fog lamps will not illuminate. Press the bottom
of the switch to turn the fog lamps off.
The fog lamps will go off whenever you change to
high
-beam headlamps. When you return to low beams,
the fog lamps will come on again.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim the
instrument panel lights
by turning the interior
lamps thumbwheel.
Turn the thumbwheel upward to increase the brightness
of the instrument panel lights. Turn the thumbwheel
downward to decrease the brightness.

2-39
Parade Mode
The instrument panel brightness control has an added
feature called parade mode to assist you in seeing
certain instrument panel controls if your headlamps are
on in the daylight. Without turning the courtesy lamps
on, turn the instrument panel brightness thumbwheel all
the way to the top. The radio, season/trip odometer,
gearshift selection indicator on the instrument panel
cluster and the heating and air conditioning controls will
come on at their maximum brightness. This will occur
only with the parking lamps or headlamps on.
Courtesy Lamps
When any door is opened, several lamps come on. These
lamps are courtesy lamps. They make it easy for you to
enter and leave your vehicle. You can also turn these
lamps on by turning the interior lamps dial all the way
up or by turning on each individual lamp.
Illuminated Entry
Your courtesy lamps will come on and stay on for a set
time whenever you press UNLOCK on the remote
keyless entry transmitter (if equipped).If you open a door, the lamps will stay on while it's open
then turn off automatically about 25 seconds after you
close it. If you press UNLOCK and don't open a door,
the lamps will turn off after about 40 seconds.
Illuminated entry includes a feature called theater
dimming. With theater dimming, the lamps don't just
turn off at the end of the delay time. Instead, they slowly
dim after the delay time until they go out. The delay
time is cancelled if you turn the ignition key to ON, so
the lamps will dim out right away. When the ignition is
on, illuminated entry is inactive, which means the
courtesy lamps won't come on unless a door is opened.
Illumination on Door Handle Activation
Illumination on door handle activation is a standard
feature intended to provide enhanced security and
convenience by allowing the driver to activate the
vehicle interior illumination without unlocking or
opening any vehicle door.
The ignition must be off and the doors locked for the
illumination on door handle activation to work. The
illumination on door handle activation feature can
function in two ways.

2-40
If the driver pulls and releases any front door handle
within one second, the interior lamps will illuminate until:

The ignition is turned to ON,

the power door locks are activated or

an illumination period of 25 seconds has elapsed.
Or, if the driver pulls and holds any front door handle
for more than one second, the interior lamps will
illuminate until:

The ignition is turned to ON,

the door handle is released or

an illumination period of 50 seconds has elapsed.
If during the illumination period a door is opened, the timed
illumination period will be cancelled, though the interior
lamps will remain on because a vehicle door is open.
Delayed Illumination
The delayed illumination feature will continue to
illuminate the interior for 25 seconds after all doors have
been closed so that you can find the ignition and buckle
your seat belt at night. Delayed illumination will not occur
while the ignition is in ON. After 25 seconds have elapsed,
the interior lamps will slowly fade out. The lamps will
fade out before 25 seconds have elapsed if you:
Turn the ignition to ON.

Lock all doors using your remote keyless entry
transmitter (if equipped).

Lock the doors using the power door lock switch.
If during the delayed illumination period a door is opened,
the timed illumination period will be cancelled, though the
interior lamps will remain on because a door is open.
Exit Illumination
To see better when exiting your vehicle at night, your
vehicle is equipped with an exit illumination feature.
The interior lamps will illuminate for up to 25 seconds
when you remove your key from the ignition. After 25
seconds have elapsed, the interior lamps will slowly
fade out. The lamps will fade out before the 25 seconds
have elapsed if you:

Turn the ignition to ON.

Lock all doors using your remote keyless entry
transmitter (if equipped).

Lock the doors using the power door lock switch.
When any door is opened, exit illumination is cancelled.
The interior lamps will stay on when any door is open.
The interior lamps may stay on for up to 25 seconds
after all the doors have been closed if they have not been
locked. See ªDelayed Illuminationº in the Index.

2-41 Battery Saver
Your vehicle has a feature to help prevent you from
draining the battery in case you accidentally leave an
interior or trunk lamp on. If you leave any of these
lamps on while the ignition is in ACC or OFF, they will
automatically turn off after 20 minutes. The lamps won't
come back on until you do one of the following:

Turn the ignition to ON,

turn the interior lamp dial all the way up or

open (or close and reopen) a door that is closed.
Please note that if your vehicle has less than 15 miles
(25 km) on the odometer, the battery saver will turn off
the lamps after only three minutes.
Mirrors
Adjust all mirrors so you can see clearly when you are
sitting in a comfortable position.
Inside Day/Night Rearview Mirror
To reduce glare from lamps behind you, push the lever
located on the bottom center of the mirror away from
you to the night position. To return the mirror back to
the day position, pull the lever toward you.
Electrochromic Day/Night Rearview Mirror
with Compass and Map Lamps (If Equipped)
Your vehicle may have an automatic electrochromic
day/night rearview mirror with a compass and map lamps.
This mirror automatically changes to reduce glare from
headlamps behind you. A time delay feature prevents
rapid changing from the day to night positions while
driving under lights and through traffic.

2-42
The mirror includes two map lamps, an automatic
dimming function and an eight
-point compass display in
the upper corner of the mirror face. When the compass
display is turned on, the compass automatically
calibrates as the vehicle is driven.The automatic dimming feature is turned on or off by
pressing the IO button located on the lower part of the
mirror. Press and hold the IO button for up to three
seconds to turn this feature on or off.
The compass display feature is turned on or off by
pressing the IO button for three seconds or more.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror housing.
Compass Calibration
To place the compass into calibration mode, press both
map lamp buttons and hold for over eight seconds until the
letter ªCº is displayed in the mirror compass window.
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display indicates a direction, or

drive the vehicle on your everyday routine.